ABB ATS Annunciator Manuel utilisateur

—

QUICK START GUIDE

ATS Annunciator - MODBUS

ATS Annunciator monitors and controls up to 8 Automatic Transfer Switches equipped

with the MX150/250 Controller.

Before getting started, have the following tools and information available:

• PC or Laptop with USB

• USB to RS-485 adapter - FTDI Chip USB-RS485-WE-1800-BT or similar.

• ATS Annunciator Tool - PC graphic user interface for ATS Annunciator configuration

• Screw Driver - Phillips #2

Review Information sections before beginning installation. Information sections follow installation steps

—

Step 1 - Mount Annunciator

1. Attach both mounting brackets to unit - 2 screws each bracket

Brackets may be attached to top and bottom or left and right sides.

Orient brackets for wall or flush mount.

2. Mount unit to desired NEMA-1 location.

—

Step 2 - Run Conduits

Run conduits

Between the Annunciator and all ATSs.

Between the Annunciator and the power source.

Knockouts are located on all 4 sides of the Annunciator.

—

Step 3 - Ground Annunciator

Ground to 6-32 stud inside box.

Knockouts (typical)

Ground Lug Landing

Inside box

—

Step 4 - Connect MODBUS Networks

MODBUS networks - See Information: MODBUS Networks

• Networks may be either Singly Terminated or Doubly

Terminated.

• The Annunciator has two separate MODBUSs.

ATS MODBUS connects to ATSs - 8 max.

PC MODBUS connects a PC to Annunciators - max 32.

MODBUS connections are to a detachable terminal block.

1. Open Annunciator - remove front cover screws.

2. Connect MODBUS cables :

a. ATS MODBUS to ATSs

b.PC MODBUS to PC and additional Annunciators, if present.

3. Terminate ATS MODBUS - typically in the ATS at one or both

ends of the bus.

4. Terminate the PC MODBUS at its non-PC end (typical):

a. The Annunciator at the non-PC end of the bus: Place jumper

across HDR5 positions 2&3.

b.All other Annunciators: Place jumper across HDR5 positions

1&2.

Pin Signal

1ATS MODBUS A

2ATS MODBUS B

3MODBUS RETURN

4PC MODBUS A

5PC MODBUS B

MODBUS Detachable Terminal Block (HDR4)

16AWG max.

HDR5

PC MODBUS Termination

Jumper 2&3: terminated

Jumper 1&2: Not terminated (shown)

Power Detachable

Terminal Block

(provided

attached to HDR3)

(Step 5)

MODBUS Detachable Terminal Block

(provided attached to HDR4)

Status LED

Factory Reset and

Firmware Update

switch

Annunciator Card - on inside of front cover

—

Step 6 - Configure Annunciator - ATS Annunciator Tool

The ATS Annunciator Tool is graphic user interface that runs on a PC and communicates with the Annunciator via the PC

MODBUS connection through an external USB to RS-485 adapter (not furnished).

—

Step 5 - Connect Power

Power connections are to a detachable terminal block (provided

attached to HDR3, see Step 4 figure).

Input voltage range: 16 - 30VAC or VDC

Customer supplied

24V AC or DC

Class2, 40VA

Ground

16AWG max.

Plug into HDR3

1. PC Serial Port Settings > Serial Port - set per the USB to RS-485 adapter instructions; Connect .

2. Annunciator Information > Annunciator ID - Select Annunciator to communicate with from list of connected IDs.

3. From PC (Host) MODBUS Port Settings > Annunciator ID - Configure as specified in site installation instructions, if

provided.

Set/change Annunciator ID from list IDs (1 -32); SUBMIT.

Each Annunciator on the network must have a unique ID. Factory default ID is 1.

Procedure for setting IDs for multiple Annunciators

a. Verify no connected Annunciator has ID = 1 - View list of connected IDs above.

b. Connect a factory fresh Annunciator (ID=1).

c. Select Annunciator ID 1 per step 2 ( ) above.

d. Change Annunciator ID to a unique number other than 1 per step 3 ( ).

e. Repeat from step a for additional Annunciators.

Remove Annunciators from the PC MODBUS network by removing their power connector or the PC MODBUS detachable

block from their circuit card (see Step 4). Then Disconnect and Connect the Annunciator Tool to re-scan the PC

MODBUS.

4. To ATS MODBUS Port Settings; click SUBMIT.

ATS-1: through ATS-8: -

For each desired Annunciator ATS position select the desired ATS ID from list IDs (1 -247) or “None” as specified in the site

installation instructions.

“None” must be selected for each Annunciator ATS position not connected to an ATS.

Click SUBMIT.

Multiple ATSs with the same ID will be indicated by continuously increasing error count . See Troubleshooting (page 9).

5. Other Settings and Controls - as specified in site installation instructions.

6. Repeat from step 2 for additional Annunciators.

Note: Re-scan may be necessary to discover newly connected or disconnected Annunciators. Disconnect and Connect the

Annunciator Tool to re-scan the PC MODBUS.

—

LEDs and Operation

KEY SWITCH

The MONITOR position allows operation of LEDs only.

The CONTROL position allows operation of LEDs and the pushbuttons.

Power LED

Indicates Annunciator is powered.

SOURCE — S1 (Normal) LED (Green)

Indicates that the corresponding Transfer Switch has an acceptable Normal source.

SOURCE — S2 (Emergency) LED (Red)

Indicates that the corresponding Transfer Switch has an acceptable Emergency source.

POSITION — S1 (Normal) LED (Green)

Indicates that the corresponding Transfer Switch load is connected to the Normal source.

POSITION — S2 (Emergency) LED (Red)

Indicates that the corresponding Transfer Switch load is connected to the Emergency source.

TIME DELAY — ACTIVE LED (Yellow)

Indicates that the corresponding Transfer Switch has a timer functioning. Timers monitored include all timers

associated with delaying

transfer in either direction.

TIME DELAY — SKIP Push Button

Immediately skip (lapse / terminate) T or W timer whichever is timing concurrent with pushbutton activation.

ATS timers will be bypassed during a test sequence if pressed before the TEST — Initiate Push Button

TEST — IN PROGRESS LED (Yellow)

Indicates the corresponding Transfer Switch is in a test mode. Indication will occur whether the test is initiated at the

annunciator or

locally at the ATS.

TEST — INITIATE/CANCEL Push Button

Begins/Cancels a load transfer test sequence (power loss simulation). Press and release to Begin/Cancel Test.

T E S T transfers to the emergency source.

Transfer is complete when both S2 Position and Source LEDs illuminate.

Transfer is complete when both S1 Position and Source LEDs illuminate.

CANCEL ends the test and transfers back to the normal source.

(Key Switch must be in the Control position)

LAMP TEST — Initiate Push Button

Turns all LEDs on for approximately 10 seconds.

Power LED

—

Information

MODBUS Networks

Networks may be either Singly Terminated or Doubly Terminated.

The Annunciator has two separate MODBUSs.

• ATS MODBUS connects to ATSs. - 8 max.

• PC MODBUS connects a PC to Annunciators - max 32.

PC MODBUS Network - 1 per network

ATSs - max 8 per Annunciator

ATS MODBUS Network - 1 per Annunciator

ATSs - max 8 per Annunciator

ATS MODBUS Network - 1 per Annunciator

Annunciators - max 32 per network

—

Network Termination

Cables:

• 300V rated insulation - Belden 9463

• 600V rated insulation - Belden 3072F

Resistors: 105Ω

PC AA AAAA

ATS ATS ATS ATS

ATSATSATSATS

Singly Terminated Network (Daisy Chain)

Maximum Total Network Cable Length: 500 M (1,640 ft)

Doubly Terminated Network (Daisy Chain)

Maximum Total Network Cable Length: 2,700 M (8,850 ft)

—

Information

—

MODBUS Device IDs

Each device on a MODBUS Network must have a unique ID.

Non-unique IDs cause communications conflicts and must be resolved. See Troubleshooting.

ATS IDs are set in the ATS MODBUS interface.

Annunciator IDs are set via the ATS Annunciator Tool (Step 6).

—

Factory reset

Factory default settings are Annunciator ID=1 ( in Step 6) in and no configured ATS ( in Step 6 all “None”).

Press and hold Factory Reset and Firmware Update switch until the Status LED turns red (5 seconds) - in figure in Step 4.

The Status LED will be green when Reset is complete.

—

Firmware Update

1.Download the Remote Upgrade Program to the PC - See Reference Documents.

2.Press and release Factory Reset and Firmware Update switch until the Status LED turns red (5 seconds) - in figure in

Step 4. The Status LED will blink red.

3.Run the Remote Upgrade Program on the PC.

a. Establish communications with the Annunciator.

b. Follow instructions as presented by the Remote Upgrade Program.

The Status LED will be green when upgrade is complete.

It may be necessary to press and release S2 to exit the programming mode.

2. 4.

—

Troubleshooting

—

MODBUS Device Address Conflict

Each MODBUS device must be configured with a unique address. Duplicate MODBUS IDs will cause indeterminate

errors

1.Check power supply for proper connection to annunciator unit. (Power LED inside unit will be ON if power supply is

connected properly). See Step 5.

All LEDs Are OFF

1.Check power supply for proper connection to annunciator unit. (Power LED inside unit will be ON if power supply is

connected properly). See Step 5.

LEDs for One or More ATSs Are All OFF

1.LEDs for ATS configured as “None” will all be OFF. See Configure Annunciator.

2.Are network terminations on ATS units connected?

3.Are all ATS units powered?Are all ATS units equipped with network interface cards?

4.Are all ATS units equipped with network interface cards?

Position and Source Availability LEDs Flash ON and OFF

This indicates that network connections are open between annunciator and corresponding ATS.

1.Is one of more ATS configured as present (not “None”), but not present on the network? See Configure Annunciator?

2.Are network terminations on remote ATS units connected?

3.Are all ATS units powered?

4.Are all ATS units equipped with optional MODBUS Interface Card (71R-2200 Modbus Card) and network cable connected?

—

Specifications and Application

• Specifications and ordering information are in the brochures listed in Reference Documents.

• Installation Environment - Install in Network Telecommunication Facilities, OSP, or where NEC applies.

—

Notes

Table des matières

Autres manuels ABB Contrôleurs

ABB

ABB LP Manuel utilisateur

ABB

ABB PSTX 30***105 Manuel utilisateur

ABB

ABB ACS150 series Manuel utilisateur

ABB

ABB ACH550-PCR Manuel utilisateur

ABB

ABB i-bus KNX Room Master Premium RM/S 2.1 Manuel utilisateur

ABB

ABB ACS 600 Series Manuel utilisateur

ABB

ABB UMC22-FBP Manuel de la liste des pièces

ABB

ABB ACS880 Series Manuel du propriétaire

ABB

ABB PST Manuel

ABB

ABB ACH400 Series Manuel utilisateur

ABB

ABB ACS880-04 drive modules Manuel utilisateur

ABB

ABB Relion 630 Series Manuel utilisateur

ABB

ABB DSQC 667 Instructions d'utilisation

ABB

ABB ACS310 Manuel d'installation et d'exploitation

ABB

ABB ACS150 series Manuel utilisateur

ABB

ABB MotiFlex e180 Guide de l'utilisateur

ABB

ABB UMC100-FBP Manuel de la liste des pièces

ABB

ABB Contrac PME120AI Manuel utilisateur

ABB

ABB AC 010 Manuel utilisateur

ABB

ABB i-bus KNX Manuel utilisateur

ABB

ABB AC 800M Manuel utilisateur

ABB

ABB ControlMaster Series Manuel utilisateur

ABB

ABB AC500 Series Manuel

ABB

ABB RHD8000 Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur