4DRC F3 Manuel utilisateur
AERIUM 4DRC F3
drone
instructions for use
For models:
4DRC F3 4K (without GPS) - the GPS features listed in the
manual are not valid for this model
4DRC F3 GPS 1080P
4DRC F3 GPS 4K
For users over 14 years of age
Registration is compulsory for all drones with a camera, more
at:
https://www.letejtezodpovedne.cz/
It is prohibited to use any model of drone within a 10
km radius on the sides of the airport and within 20 km
of either end of the runway and on civil air routes to
meet the electromagnetic environment requirements
for aeronautical communications.
No model of drone is allowed in the no-fly zones
established by the relevant state authorities.
1.The packaging and instructions for use provide important
information and should be kept for future reference.
2.You are responsible for ensuring that this drone does not
cause any personal injury or property damage.
3.The commissioning and assembly of the drone must be strictly
in accordance with the operating instructions. 4. Make sure that
the drone is 2-3 m away from the operator and other persons
when flying, so that the drone does not hit the head, face and
body of a person during flight and landing and cause injury to
him/her.
4. Neither our company nor the dealer shall be liable for any
loss, damage or personal injury resulting from improper use or
operation.
5. Children over 14 years of age may operate this drone under
adult supervision and children under 14 years of age may not
operate this product.
6.Please install and use this product correctly in accordance with
the instruction manual,some parts must be assembled by adults.
7. This product contains small parts, please keep out of reach of
children to prevent accidental ingestion or suffocation.
8. It is forbidden to operate it on the road or on waterlogged
ground to avoid possible accidents.
9. Please clean up the packaging materials in time to
avoid harm to children.
10.Do not disassemble or reassemble the drone to avoid any
malfunctions.
11.The USB charging cable must be plugged into the
designated 5V = 2A power source as marked on the
product.
12.Only the original USB charging cable may be used.
1. Accessories
Drone 1xcharger 1xreplacement propeller blades 4xbatteries 3x (2x) according to
model screwdriver instructions
2. Drone component names:
3. Propeller blade installation and replacement
3.1 Unscrew the screw and
remove the propeller blades.
Note: The letters A, B, C and
D are printed on the blade,
A=C, B=D, place them
according to the drawing,
otherwise the drone will not be
able to take off.
3.2 Unscrew the screw to
separate the two blades from
the connecting parts and
replace them. (Replace
damaged B/D blades with B/D
blades and replace damaged
A/C blades with A/C blades,
any incorrect replacement will
cause the drone to not take
off.)
Engin
e
Propel
ler
blade
holder
clip
Propeller
blades
Batteri
es
Drone
body
LED lights
Camera
4.3 Charging: insert the USB interface of the charging cable into the USB ports of
the computer (or use the output: 5V = 2A power adapter) and connect the other
side of the USB interface to the battery socket. When charging, the USB drone's
red light will turn on and the green light will flash; when the battery is fully charged,
the red light will turn off and the green light will turn on, indicating that charging is
complete.
5. Names included with the remote control:
Fine tuning ( hold )
/ gear Power
indicator Left
joystick
Switch (long press)
Calibration of
geomagnetism (compass)
( 3 s press)
Immediate take-off/landing
Hold down
both
buttons in
an
emergency
.
Familiarity with the
remote control
indicators:
Photo/video (long
press)
Right joystick
GPS control -
long press
Free mode
Immediate return
Common/GPS button: after adjusting the frequency, long press this button for
3 seconds to select the common mode and GPS mode (default GPS mode,
GPS light is on, if you select common mode, GPS light is off).
Free mode button: Press the button again to exit the free mode, the light goes off.
Return button: press the button once to return and the return light will
illuminate. Press the button again to cancel the return, the light goes off.
4.1 Press the drone battery lock
4.2 Remove the
battery
6. Installing the remote control battery:
Notes:
Battery installation:
4.1 Press the battery cover
button with a screwdriver to
remove the battery cover.
4.2 Follow the polarity
instructions on the battery
holder to remove the battery.
and install 4 "AAA" batteries
(not included).
1. When installing the batteries, pay attention to
the anode and cathode of the batteries and their
markings on the battery packaging.
2. Please do not mix new and old batteries.
3. Please do not mix different types of
lithium batteries.
Safety precautions for charging:
To prevent damage or explosion, do not insert charged batteries
into high temperature areas such as open flames or electric
heating equipment.
●Do not throw batteries, prevent them from falling.
●Do not disassemble the batteries.
●Do not soak batteries in water. Store batteries in a dry place.
●Charge batteries under adult supervision.
7. Instructions for downloading and
installing the app:
Warning:
When the drone is not in
use, disconnect the
battery plug from the
drone's power connector
to avoid damaging the
battery.
7.1
Download and install the app
For Android, scan the QR code, open the website in your browser and download the software.
7.2
Linking instructions
●
Turn on the power of the drone, enter "Settings" (mobile phone or IPAD), open the
WiFi wireless network, find the device "4DRC-4K-GPS *****" in the wireless network
search list and connect the device, exit Settings when connected.
●
Open the "4DRC PRO" icon on your mobile phone and enter the control interface (stay
away from other signal sources when controlling the drone).
Open the 4DRC CLICK on the "GO" buttonClick on "MORE FUNCTION " Enter the "FUNCTION MENU"
8. Introduction to the functions of the application control
interface:
GPS
More
functions
Return /
Back
Take-
off/landing
Immediate
return
Unlocking
Radar,
direction
Informatio
n
about the distance
Connection
status
WiFi signal
Battery status
More settings
Photo/Vide
o Switch
Media Library
Flight records
Zoom
Filters
3D
Inverted camera
Unlock
Gesture
shooting
Adding music
Multi-seat flight
Next Circular
flight
Find a drone
Speed limiter
Switching cameras Touch
joystick
Beginner
mod
e Distance information
Default 30m, (20m-2000m)
Flight height
Default 30m, (10m-120m)
On/off
Retrieved from
Note: Turn off Beginner mode with advanced flight operations,
then adjust the flight distance and altitude to allow the drone to
fly further!
9. Pre-flight environmental requirements:
Operate the drone in an outdoor open area free of rain and snow and with wind strengths
below level 3 and stay away from crowds, trees, power lines, tall buildings, airports and
signal towers.
Do not use it in enclosed areas or in a place with a weak GPS signal.
10. Preparation for flight:
WARNING: Please make sure the drone/remote is fully charged, otherwise it cannot take
off.
10.1
Turn on the power to the drone, place it
on the launch pad - the horizontal spot for
automatic frequency adjustment, the front
white indicator light and the red indicator light
on the rear arm blink (battery light is on).
Note: Adjust the direction of the drone so that the front of the drone is facing forward and
the drone is positioned horizontally.
10.2
Open the WiFi function on your mobile
phone and select "4DRC-4K- GPS*****" in the
WiFi list, connect the device and then open the
app.
10.3
Turn on the remote control (default
mode), long press the "ON/OFF" button on the
remote control (step 1), the power light will
come on. Push the throttle stick up (step 2)
and then down (step 3). When the pairing
frequency is successfully paired, the UAV
indicator light will turn on instead of blinking.
Autres manuels pour F3
1
Table des matières
Autres manuels 4DRC Drone
