4Ddoors 4DR1 v4 Guide de démarrage rapide

4DOMU01A-2

Installation instructions and Owner's manual

Roller door operator

4DR1 v4

READ THIS MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION

Installer: Permanently attach manual to the wall.

Inventory

Operator Unit

Anti-Coning Clip x2 sets

Weight Bar & mounting screw set x1

Wireless Wall Button x1 *

U-bolt + Saddle x1 set

Manual + Safety Label

Remote Handset x2 *

* Optional Accessories

* Items and quantity may differ to images shown

Electrical Rating

Input AC 220V 50/60Hz

Max. Current 2A

Power 100W

Standby Power <2W

Motor

Type DC 24V

Max. Capacity 1000N

Recommended Lifting Forces

Max. Lifting Force 60kg

Rated Lifting Force 40kg

Door Type

Max. Door Size 20.5m2

Max. Door Height 4.6m

Door Travel Limits 4.5 turns of door drum approx.

Courtesy Light

Light Source 6 x Ultra Bright LEDs

Lighting Time 2.5 minutes

Transmitter

Frequency 433MHz

Operation Range 50m (open field)

Coding Type Fixed-code

Battery 12V (A23 Alkaline) x 1

Features

Soft opening and closing

Safety reverse on closing and stop on opening

Digital interface for RH/LH setting, force adjustment, etc.

Miscellaneous

Operating Temperature -20oC ~ +50oC

Dimension (mm) 434 L x 248 W x 190H

Weight 5.4kg approx.

SPECIFICATION

PRE-INSTALLATION NOTES

Ensure there is a properly earthed mains supply socket adjacent to where the operator is to be fit-

ted.

If the operator is being fitted at the same time as the new door installation, read these instructions in

conjunction with the door installation instructions.

If the operator is being retro-fitted, make sure the door operates smoothly and is properly balanced.

N.B.: SPECIAL CARE SHOULD BE TAKEN IF RE-TENSIONING OF THE DOOR IS REQUIRED.

Door Type Minimum side clearance

“A” Series ( 25mm deep tracks ) 90mm

“AA” Series (50mm deep tracks ) 115mm

All doors with Windlok Tracks subject to Drum Position 140mm

Pre-Installation Notes 4

Important Notices 5

Installation Instructions 6

Connectors 7

Setting Direction of Operation 8

Setting UP-Limit 9

Setting DOWN-Limit 10

Sensitivity Auto-Learning 11

Manual Sensitivity Adjustment (For Installers Only) 12

Programming Transmitter 13

Setting Auto-Closing Timer 14

Trouble-Shooting 15

Parts Breakdown 16

Parts List 17

Warranty 18

The operator may be fitted to either the RIGHT or LEFT hand side of the roller door.

Check that there is sufficient side clearance to fit the operator unit as below listed:

TABLE OF CONTENTS

IMPORTANT : PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO

COMMENCING THE INSTALLATION OF THE OPERATOR UNIT.

This Automatic Operator has been designed to provide years of trouble-free

use.

READ THESE IMPORTANT SAFETY RULES FIRST

Keep the garage door balanced. Sticking or binding doors must be repaired.

Garage door, door springs, brackets and their hardware are under extreme

tension and can cause serious personal injury. Do not attempt adjustment. Call

for professional garage door service .

Do not wear rings, watches or loose clothing while installing or servicing a garage

door operator.

Installation and wiring must be in compliance with your local building and

electrical codes. Connect the power cord only to properly earthed mains.

The safety reverse system test is very important. Your garage door must

reverse when obstructed on closing. Failure to properly adjust the operator may

result in serious personal injury from a closing garage door. Repeat the test once

a month and make any needed adjustments. (See Sensitivity adjustment).

This unit should not be installed in a damp or wet space.

Pull down on the Emergency Release handle to disengage the motor drive ONLY

when the drive is switched OFF and, if possible, when the door is fully closed.

Do not use the sensitivity adjustments to compensate for a binding or sticking

garage door. Excessive sensitivity will interfere with the proper operation of the

Safety Reverse System or damage the garage door.

Disengage all existing garage door locks to avoid damage to garage door.

Install any additional Push Buttons in a location where the garage door is visible,

but out of the reach of children. Do not allow children to operate push button/s or

remote control/s. Serious personal injury from a closing garage door may result

from misuse of the operator.

CAUTION: Activate operator only when the door is in full view, free of

obstructions and the operator is properly adjusted. No one should enter or leave

the garage while the door is in motion. Do not allow children to play near the door.

Disconnect electric power to the garage door operator before making repairs or

removing covers.

IMPORTANT: Fix the caution label supplied to the rear of the garage door as

a reminder of safe operating procedures.

NOTE: 1. When you disengage the unit, please move the door gently.

2. Direction of operation (L/R) must be set correctly before operation.

CAUTION

DANGER

IF THERE IS ANY PROBLEM PLEASE CONTACT YOUR LOCAL

SUPPLIER OF THIS OPERATOR

IMPORTANT NOTICES

1. Fit anti-coning collar TIGHT TO SHAFT against drum at

opposite end of curtain to the motor using anti-coning clip

supplied in kit as shown in Fig.1.

2. Left off about pinning the curtain to the drum wheel.

Ensure the curtain is pinned to the drum wheel.

3. Roll up door with at least 100mm of curtain hanging down

in the tracks.

4. Ensure that the U-bolt on the end of the door opposite the

end to which the operator is to be fitted is tightened

securely. This U-bolt holds all the spring tension on the

door once the other U-bolt is released.

5. Slide drive unit onto shaft as shown in Fig.2. Ensure the

drive forks engage fully with the narrowest spoke on drum

wheel.

6. For ease of installation, the sun gear can be disengaged

for free rotation by pulling the Emergency Release handle

downwards. To re-engage and lock the sun gear, pull down

on the handle once again until a "click" is heard.

Caution : Operator must be ENGAGED before

proceeding further installation.

Fig.1

Engage - Pull down the release cord firmly with 'click'

(handle is on same level as bottom of the operator)

Disengage - Pull down the release cord firmly with 'click'

(handle is below the bottom of the operator)

Emergency Release

Fig.2

INSTALLATION INSTRUCTIONS

CONNECTORS

OFF 2.5 min

Backup Bat-

LED Light

Auto-Close Timer

II. Miscellaneous Control and Terminals

* Auto Close Timer function will only work when Photo Eye System is properly installed.

!WARNING : This operator system is equipped with an unattended operation feature

when Photo Eye System is applied. The door could move unexpectedly.

NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR!

To activate Auto-Close Operation Turn the knob towards “ + ” for maximum delay time of

2.5 minutes.

To deactivate Auto-Close Operation Turn the knob fully towards “－ ”.

Photo Eye Selection

Jumper off — Selected

Jumper on — Unselected Push Button

DC 24V

Ext. Aerial

GND

Photo Eye

UP RADIO SET FORCE

Manual Operate

Button

I. Main Control Panel

LED Indicators

UP RADIO SET FORCE

For using the operator the first time, it is necessary to set the direction of

operation.

1. Connect power supply, both “UP” and “DOWN” LEDs are on.

3. Press “RADIO SET” button to confirm setting. The “OK” LED is on with 2 beeps.

2. Initialize the operational direction by pressing “UP” or “DOWN” button for the

correct direction setting according to the illustrations below. The correspond-

ing LED is on upon key input.

Caution : Make sure the drive unit is set for the correct side of installation!

To reset installation direction, press the “LIMIT” button constantly until both “UP”

and “DOWN” LEDs are ON, repeat steps 2 and 3 to set the appropriate direction.

Indoor view Indoor view

SETTING DIRECTION OF OPERATION

UP RADIO SET FORCE

1. Press “LIMIT” button once to enter limit-setting mode. “UP” LED is on.

2. Press & hold the “UP” button, release the “UP” button when the door reaches

the desired up limit position.

3. During limit-setting mode, press “UP” or “DOWN” to fine-tune to desired UP

limit position.

4. When the door is at the desired UP limit position, press “LIMIT” button once,

“OK” LED flashes and goes out. UP limit is set.

SETTING UP LIMIT

UP RADIO SET FORCE

1. Press “LIMIT” button twice to enter DOWN-limit setting. “DOWN” LED is on.

2. Press & hold the “DOWN” button, release the “DOWN” button when the door

reaches the desired down limit position.

3. During limit-setting mode, press “UP” or “DOWN” to fine-tune to desired down

limit position.

4. When the door is at the desired DOWN limit position, press “LIMIT” button

once, “OK” LED flashes twice and both “UP” and “DOWN” LEDs are on.

DOWN limit is set and the operator is ready for Sensitivity Auto-Learning.

SETTING DOWN LIMIT

Table des matières

Autres manuels 4Ddoors Système d'ouverture de porte

4Ddoors

4Ddoors 4DR2 Instructions de montage

4Ddoors

4Ddoors CX1024 Manuel

Manuels Système d'ouverture de porte populaires d'autres marques

Pamex

Pamex KT-INP35 Manuel utilisateur

Label

Label NEPTIS/LE Manuel utilisateur

Cal-Royal

Cal-Royal N-F77CVR Manuel utilisateur

Scrigno

Scrigno OPEN1000 Manuel utilisateur

TriMark

TriMark UM 34 Manuel utilisateur

BFT

BFT WIND RMB 130B 200 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Besam

Besam Swingmaster MP Mode d’emploi

CRL

CRL SENIOR PRIMA Manuel utilisateur

Assa Abloy

Assa Abloy SARGENT 1431 Series Manuel utilisateur

GAL

GAL MOVFR Fiche technique

Olide

Olide 120B Manuel utilisateur

Normstahl

Normstahl IDO7 Manuel utilisateur

Häfele

Häfele Finetta T 70 VF Manuel utilisateur

AGS

AGS D-PL Manuel

Stanley

Stanley MA900ñ Instructions d'installation

WITTUR

WITTUR Hydra Plus UD300 Manuel

Alutech

Alutech TR-3019-230E-ICU Instructions d'installation et d'utilisation