3SIXT 3S-0959 Manuel utilisateur
3
MIC
AVRESETUSB
THE BASICS
Buttons & Ports
1- Microphone
2- Mini HDMI Out
3- MicroSD Slot
4- Mode Button
5- OK Button
6- Menu Button
7- Up Button
8- On/Off Button
9- Down Button
10- Mini USB Port
11- Reset Button
12- Audio Out
13- Mount Slot
14- Lens
15- Infra Red LED
16- Speaker
17- Operating LED
18- Charging LED
19- Dust Cover
4
Package Contents
3SIXT Car DVR
Car Charger
USB Cable
User Guide
Window Mount
Installation of the Camera
1. Clean the interior of your windscreen ensuring that the desired point of
installation is free of dust and is not obstructing the drivers’ view.
2. Attach the camera to the included mount by inserting the mount’s
lock peg into the mounting socket (13) on the camera firmly sliding the
mount from right to left along the mount connection locking the
camera in place.
3. Remove the protective stickers on the suction cup of the mount, the
2.7” LCD Screen and the lens.
4. With the suction mount lock switch in the up position, press the
suction cup onto the desired position on your windscreen.
5. Lock the mount in place by pressing the lock switch in the down
position.
6. Use the nut to adjust the angle and position of the camera and tighten
to lock your positioning.
7. Connect the camera to power using the included miniUSB power
supply.
54
1. First, make sure that the camera is
OFF before inserting or removing
the miniUSB charging connector
2. Check the miniUSB port (10) for any
obstructions or foreign matter
3. Insert the miniUSB connector from
your connected car charger or
charge cable into the miniUSB port
(10) on the camera.
4. The charging indicator light (18) will
illuminate red whilst charging and
turn off when the battery capacity
is at 100%
5. The MiniUSB connector can only
be inserted into the port one way.
Please do not force the connector
into the port.
6. Keep the miniUSB port clear of any
obstructions
AVRESETUSB
AVRESETUSB
CHARGING THE BATTERY
The camera is designed to be used with a car charger
(included). The internal battery is an emergency back
up and is not designed to power the camera for the
intended usage.
WARNING: Using a car charger other than a 5V 1A Charger
can damage the camera battery and could result in fire or
leakage. Only use chargers marked: Output 5V 1A.
6
1. Make sure the camera is OFF when
inserting or removing the microSD
card.
2. Using your fingernail gently remove
the dust cover (20) to expose the
microSD slot (17).
3. Make sure the memory card is
inserted in the correct direction
(the gold contacts of the microSD
card should face the front of the
camera) into the microSD card slot
(17). Failure to do so may lead to
damaged or lost data.
4. To remove the microSD card,
press down on the card with your
fingernail until it clicks and pops up.
5. If a microSD card is removed
or power supply is interrupted
when the camera or computer is
connected to the card (i.e. during
reading, writing and formatting),
your captured images and video may
be lost or damaged.
AVRESETUSB
MicroSD
Mini HDMI
MIC
INSTALLING THE MICROSD CARD
It is recommended to use 32GB Class 10 microSD cards
for maximum performance.
76
TURNING THE CAMERA ON/OFF
Fully Charge the battery and insert the microSD card as
described on page 5 & 6.
AUTOMATICALLY TURN ON THE CAMERA
When the camera is connected to the car charger and the car is started
the camera is automatically activated and video recording will
automatically commence. The LCD screen displays the 3SIXT welcome logo
and a start up tone is emitted. The Green LED (18) will be flashing.
AUTOMATICALLY TURN OFF THE CAMERA
When the camera is connected to the car charger and the car is turned
off, the camera will automatically be de-activated and the current video
recording will be automatically saved. The LCD Screen display turns OFF
and a shutdown tone is emitted.
MANUALLY TURN ON THE CAMERA
Press and hold the Power Button (8) for 2 seconds until the LCD screen
displays the 3SIXT welcome logo and a start up tone is emitted. The
camera will start recording automatically. The Green LED (18) will be
flashing.
MANUALLY TURN OFF THE CAMERA
Press and hold the Power Button for 2 seconds until the LCD Screen
displays OFF. A shutdown tone is emitted. The last file is saved
immediately. If the camera is in a “low power” state (<10%) the camera will
auto power off and save the last file.
8
IMPORTANT DASH CAMERA SETTINGS
Please take the time to review these settings. They will
ensure your camera is operating at it’s full potential.
Set Time & Date
It’s important to have your time and date set correctly as it will
record directly onto your video stream and is critical information to
prove your case to insurance companies etc.
To set the time on your camera follow the directions below,
1. Ensure you are not currently recording. If the red record
indicator is flashing at the top left of the camera’s screen,
push the OK (5) button to stop recording.
2. Push the MENU(6) button twice, taking you to the SETUP
menu
3. Using the DOWN (9) button highlight the setting named
“Date/Time” and push OK (5).
4. Use the Up (7) and Down (9) buttons to cycle through the
numbers and use the OK (5) button to confirm and move
between fields.
5. Time is set and displayed in a 24 hour format.
6. After setting the date and time the bottom DD/MM/YY
fields are used to change format that the date will be
displayed.
7. Once the date and time have been set, the MENU (6) button
can be used to save and exit back to the SETUP menu.
Set Loop Recording
Your camera has the ability to record in a Loop mode, which means
older blocks of video files will be overwritten once the memory card
becomes full. You can set the amount of video block time the
camera will record before a new video file is started. To change the
98
length of the videos that the camera records follow the directions
below.
To set the time on your camera follow the directions below:
1. Use the MODE (4) button to make sure you are in VIDEO
mode (Video camera icon will be displayed in the top left
corner of the screen).
2. Ensure you are not currently recording. If the red circle
record indicator is flashing at the top left of the camera’s
screen, push the OK (5) button to stop recording.
3. Push the MENU (6) button taking you to the VIDEO menu.
4. Use the DOWN (9) button to highlight the setting named
“Loop Recording” and push OK (5).
5. Use the UP (7) and DOWN (9) buttons to highlight the
required video length (The OFF setting will record the
longest possible loops keeping the file size under 2GB, which
is around 7 minutes at 1080P resolution).
6. To confirm selection push the OK (5) button, the camera will
take you back to the VIDEO menu.
Set G-Sensor
The G-Sensor monitors any unnatural movements of the vehicle
and logs the associated footage as “Locked” ensuring any footage
of potential incidents are not recorded over with the regular loop
footage.
To set the G-Sensor follow the directions below:
1. Use the MODE (4) button to make sure you are in VIDEO
mode (Video camera icon will be displayed in the top left
corner of the screen).
2. Ensure you are not currently recording. If the red circle
record indicator is flashing at the top left of the camera’s
screen, push the OK button to stop recording.
3. Push the MENU (6) button taking you to the VIDEO menu.
10
4. Use the DOWN (9) button to highlight the setting named
“G-Sensor” and push OK (5).
5. Using the UP(7) and DOWN (9) button, highlight the
required sensitivity of the G-Sensor (2G is the most sensitive
setting only requiring small bumps to log footage as Locked,
and 8G is the least sensitive requiring a larger amount of
activity to log footage as Locked).
6. To confirm selection push the OK (5) button, the camera will
take you back to the VIDEO menu.
Set Park Mode
Park Mode will monitor for activity using the G-Sensor after the car
is parked, even if your ignition is turned off. If activity is detected, the
camera will record 10 seconds of footage.
To set park mode on your camera follow the directions below:
1. Ensure you are not currently recording. If the red record
indicator is flashing at the top left of the camera’s screen,
push the OK (5) button to stop recording.
2. Push the Menu (7) Button twice, taking you to the SETUP
menu.
3. Using the DOWN (9) button highlight the setting named
“Park Mode” and push OK (5).
4. Using the UP (7) and DOWN (9) button, highlight the
required sensitivity of the GSensor (2G is the most sensitive
setting only requiring small bumps to trigger recording, and
8G is the least sensitive requiring a larger amount of activity
to trigger recording).
5. To confirm selection push the OK (5) button, the camera will
take you back to the SETUP menu.
Table des matières
