3rd Eye MobileVision AWT07MLED Manuel utilisateur
Thank you for purchasing our product.
Please read this User’s Manual before
using the product.
Change without Notice
AWT07MLED
7” Q TFT LCD MONITOR (LED Backlighted)
USER MANUAL
e
-4
2
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio / TV technician for help.
zYou are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
SAFETY PRECAUTIONS
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference and,
(2) This device must accept any interference received, including interference
that may cause undesired operation
3
Safety Precaution.………………………....…………………………………………..........2
Table of Content.….………………………………………………………………………3
Features….………………………………………………………………………………...4
1. Package Contents…….………………………………………………………………..5
2. TFT Installation……………………………………………….…………………………6
3. Signal Cable Description……..………………………………….…………………..7
4. Control Cable Description……..…………………………………….……………….9
5. Front Panel Control.……………………………………………………..………… 10
Main OSD Menu…….........……………………………………………….………11
Screen Menu……………………………………………………………………...12
Display ……….…………………………………………………………….…13
Camera ...……………………………….…………..................................15
Information...……………………………….…………..................................19
6. Vehicle Installation ……………………………………….……………………..20
7. Specification…..………………………………………..……………………….21
8. Attachment…..……………………………………………….……………………22
TABLE OF CONTENT
4
zAdvanced OSD Menu for easy use
zSupport up to 4 CCD Camera inputs (Mini din connector)
zExtra RCA input for multimedia while parking (VCD, DVD, Game device)
zProvide 2 Video / 1 Audio Signal Output (Live Out)
zSupport Single / Dual / Triple / Quad Screen (Cam Out)
zSignal Trigger for Side / Rear View
zAuto Day & Night Control via Photo Diode Sensor
zAuto Detection for NTSC / PAL System
zOSD Control for Individual Normal / Mirror Camera Image for every camera
zAuto power on when users are making left turn or right turn even reverse
zAble to select CAM A / B/C / R’s monitoring screen
zSupported 9.6V~32V Car power system working
zProfessional Metal Case with Anti Shocking Design
FEATURE
5
Item Qty.
1. 7” LCD Monitor 1
2. Sun-Hood 1
3. Mounting Bracket 1
4. Accessories 1
5. Control Cable 1
6. User Manual 1
1. Package Contents
6
Step 1
Check the package and make sure all parts are included.
Step 2
Clip the sun-hood on to the monitor.
Step 3
Make sure it is installed properly.
Step 4
Install the monitor on to the bracket.
Step 5
Adjust the monitor to an appropriate / comfortable viewing
angle before tightening the screws.
Step 6
Connect the control cable included to the power socket
which located at rear side of monitor.
Step 7
Monitor installation is now completed. Each control cable
wire is attached with a sticker to indicate its signal function.
Referred to the identification sticker for further installation.
2. TFT Installation
7
1. CAM R (Mini din) (NTSC/PAL system presume by this car rear CCD)
For 1st camera connection
2. CAM A (Mini din)
For 2nd camera connection
3. CAM B (Mini din)
For 3rd camera connection
4. CAM C (Mini din)
For 4th camera connection
5. LIVE VIDEO OUT (White Color RCA Jack)
On screen video loop out (for recording, second monitor or other device)
6. LIVE AUDIO OUT (Black Color RCA Jack)
On screen audio loop out (for recording, second monitor or other device)
7. AV VIDEO IN (Yellow Color RCA Jack)
Connection for any Video signal (DVD, VCD, Game)
8. AV AUDIO IN (Red Color RCA Jack)
Connection for any Audio signal (such as DVD, VCD, Game)
9. CAM OUT (Green Color RCA Jack)
Video loop out (for recording, second monitor or other device)
3. Signal Cable Description
8
Function of the Audio
※ Cam Out: Composite video loop out signal to recorder, monitor or other device.
※ Live Video/Audio Out: On screen video/audio signal loop out to recorder, monitor
or other device.
Cam A Audio from Cam A
Cam B Audio from Cam B
Cam C Audio from Cam C
Cam R Audio from Cam R
Cam A + Cam B Audio from Cam A
Cam C+ Cam R Audio from Cam R
Cam A+ Cam R Audio from Cam R
Cam R+ Cam B Audio from Cam R
Cam A + Cam C Audio from Cam A
Cam C+ Cam B Audio from Cam C
Cam R / Cam AB Audio from Cam R
Quad Audio from Cam R
AV Audio from AV
Mini Din Pin Assignment * Type 1 (Standard):
1. Video 4. +12V
2. ------- 5. GND
3. Audio 6. -------
4
32
1
65
9
1. The control cable sequence: Reverse > Right / Left / CAM C when Priority is ON. Right
/ Left / CAM C > Reverse when Priority is OFF.
2. With car power is on, the monitor power is off, when making a reverse / right / left turn,
the monitor will display default screen.
3. You may push the “JUMP” button under event trigger when Priority is OFF.
WIRE COLOR FUNCTION REMARK ON SCREEN VIEW
RED ACC POWER
BLACK GND
WHITE SW Control Active Power
Level Connect to
CAM C
BLUE Reverse Control Active Power
Level Connect to
Reverse Light
ORANGE Right Turn Control Active Power
Level Connect to
Direction Light
(R)
YELLOW Left Turn Control Active Power
Level Connect to
Direction Light
(L)
4. Control cable Description
Don’t connect the red wire (power wire) of this produc
t
directly to the battery. Connect the red wire of this produc
t
to the ACC of the ignition key switch. Failure to do so ma
y
result in permanent damage of the product.
Jum p Source P o wer
M enu
CAMR
CAM R CAM B
CAMA CAM R
10
POWER Press the power button to activate the monitor or to keep the monitor
under stand by mode (In Red Led).
SELECT With power on, press this button to select image sequence as below~
AVÆCAM A+BÆCAM C+RÆCAM A+RÆCAM R+BÆCAM A+CÆ
CAM C+BÆCAM R/ABÆCAM R+ABÆCAM AÆCAM BÆCAM CÆ
CAM R ÆAV……..
Prerequisite：Display menu ÆPriority option is “ON”
JUMP Press this button to display defined camera input, user can select
QUADÆSEQÆCAM A+BÆCAM C+RÆCAM A+RÆCAM R+BÆ
CAM A+CÆCAM C+BÆCAM R/AB ÆCAM R+AB ÆCAM A ÆCAM B
CAM CÆCAM R via OSD as default value.
Prerequisite：Display menu ÆPriority option is “ON”
MENU This encoder switch provides the following function:
1. Activate OSD menu: Press the Menu switch to activate the OSD menu.
After the OSD menu is activated, in case users does not proceed for
further set up, the OSD menu will then automatically turn off within
20 seconds.
2. Enter Function: Press the encoder switch to act as “Enter” function
under the OSD menu.
3. Volume Value: Exit the OSD menu, user can turn this switch
left or right to adjust the volume value.
5. Front Panel Control
Table des matières
Autres manuels 3rd Eye Moniteur
