3Com 7250 Manuel utilisateur

Quick Start Guide

Wireless LAN Access Point 7250

3CRWE725075

The 3Com Wireless LAN Access Point 7250 offers enterprise network standard based security and complete

centralized management, with flexible and expansive connectivity and scalability. It extends networks and

boosts productivity for centrally managed enterprises requiring scalable security solutions.

NOTE: This product must be installed by a professional technician/installer.

CAUTION: Do not connect a telephone cable into the Ethernet port; doing so can cause serious

damage to the access point.

Radio

Ethernet

Power

Access Point 7250 - Front

Console port

Ethernet port

Power supply

Access Point 7250 - Back

1 Before You Start

■Make sure that you have the following items ready for the installation:

■3Com Access Point 7250

■Standard detachable antennas

■Power supply

■Power cord

■3Com installation CD

■Ethernet category 5 straight cables (8-wire)

■For wall-mount installations you will need the following items:

Mounting plate

Mounting screws

Plastic anchors for drywall mounting

■To use the Web configuration management system, you need a computer running one of the

following operating systems and one of the following browsers:

■Operating Systems: Windows 98, Windows ME, Windows NT 4.0 (with the latest

service pack), Windows 2000, or Windows XP.

■Browsers: Internet Explorer 5.0 or later. (Internet Explorer 5.5 is available on the

installation CD.)

2 Prepare for Installation

It is advisable to connect the power and check the Ethernet cables and LEDs before installing the unit in a hard-

to-reach location.

1Observe the following power requirements:

The access point complies with the IEEE 802.3af power-over-Ethernet standard. It receives

power over category 5 straight cable. Installation requires the use of either the 3Com power

supply provided or IEEE 802.3af compliant power supply equipment (output power rated

48 V DC @ 350 mA maximum). Such equipment must be safety certified according to UL,

CSA, IEC or other applicable national or international safety requirements for the country of

use. All references to the power supply refer to equipment that meets these requirements.

Because the power supply plug is the only means of disconnecting the access point from

power, make sure the power outlet is accessible.

The power supply can be located indoors at any point between the access point and the LAN

access port where an accessible power outlet exists.

2Decide where to place the access point.

■Mounted on a wall on a stud (or other hard surface)

■Mounted on to drywall

■Placed on a flat surface

The location should be elevated and centrally located relative to users on your network. Ceiling mounting is not

recommended.

3Record the access point MAC address and serial number in a safe place before the access

point is installed in a hard-to-reach location. The MAC address is printed on the back of the

access point housing.

4Carefully unpack the standard detachable antennas. Screw the antennas on to the SMA

connectors and hand-tighten them. After network startup, you may need to adjust the antennas

to fine-tune coverage in your area.

NOTE: Regulatory restrictions dictate that when the access point is operational a minimum body-

to-antenna distance of 1 meter (3 feet) must be maintained.

The installation CD includes the User Guide, which contains more detailed information on planning, installing

and configuring the device. Additional tools and utilities are provided to assist with the management of your

network. See “Documentation and Software Utilities” on page 7 for instructions.

3 Connect the Power

The access point complies with the IEEE 802.3af power-over-Ethernet standard. It receives power over a

standard category 5 straight (8-wire) Ethernet cable. There are three ways to supply power to the access point:

■Use the AC adapter included with the Access Point 7250.

■Use an optional 3Com Integrated Power-over-Ethernet power supply. In this case, you need to

supply a second Ethernet cable to connect to the wired LAN.

■Connect the access point directly to your own Power-over-Ethernet hub or switch, which

must also comply with the IEEE 802.3af standard.

Using the Included AC Adapter

The power supply included with the Access Point 7250 is an AC adapter. Follow these steps to connect the AC

adapter:

1Connect the power cord to the power supply and plug the cord into a power outlet.

2Connect the DC power into the Access Point 7250.

CAUTION: Do not handle the antenna tips, especially after they are connected to the access

point, as this could lead to electrostatic discharge (ESD), which could damage the equipment.

Radio

Ethernet

Power

Using the included AC Adapter

Using An Optional Power-Over-Ethernet Injector

The Power-Over-Ethernet Injector can be located at any point between the access point and the LAN access

port, wherever a convenient power outlet exists. If you supply your own Ethernet cable for connecting power,

be sure that it is standard category 5 straight-through (8-wire) cable that has not been altered in any way. Use of

nonstandard cable could damage the access point.

Refer to the illustration below, and follow these steps:

1Connect one end of the Ethernet cable to the Ethernet port on the access point.

2Connect the other end of the Ethernet cable to the port labeled To Access Point on the power

supply.

3Connect the power cord to the power supply and plug the cord into a power outlet.

4To link the access point to your Ethernet network, plug one end of another Ethernet cable into

the port labeled To Hub/Switch on the power supply, and plug the other end into a LAN port

(on a hub or in a wall).

CAUTION: To avoid damaging network equipment, make sure that the cables are connected

from access point to power supply to LAN as shown and described above.

Radio

Ethernet

Power

Radio

Ethernet

Power

Using an Optional Power-over-Ethernet Injector Using an Optional Power-over-Ethernet

LAN port

4 Check the LEDs

When power is connected, the access point LEDs light up. The illustration and the following table describe the

LEDs and their functions.

5 Wall Mount Installation

1Install the mounting plate as shown in the following illustration, on either a stud (or other

hard wall surface), or onto drywall.

■Allow for a clearance of at least 25 cm (10 inches) between the ceiling and the top of the

mounting plate.

■Orient the bracket with the letter “B” at the top of the bracket.

■For installation on a wall stud, install the top screw into the stud, as shown at left in the

illustration, and then vertically align the mounting plate before installing the

bottom screw.

■For installation on to drywall, mark three screw holes using the mounting plate as a

template for vertical alignment, as shown at right in the illustration above.

■Use a 5-mm (3/16-in.) drill bit if using the plastic anchors provided.

■For drywall mounts, you can route the cable through the center opening for a seamless

appearance using one of the methods illustrated below. Alternatively, you can simply

attach the Ethernet cable to the top of the unit, allowing it to trail along the wall.

Name Description

Radio LED blinks red to indicate radio activity. Faster blinking

indicates more activity.

Ethernet LED lights yellow when 10 Mbps Ethernet link is

established. LED lights green when 100 Mbps Ethernet

link is established. LED blinks to indicate activity on the

Ethernet. Faster blinking indicates more activity.

Power LED lights green when operational code is running. LED

lights yellow when a power-on fault occurs.

RADIO

ETHERNET

POWER

If installing into drywall, use 3 plastic

anchors and 3 screws.

If installing into a stud or other

secure vertical surface, use 2 screws.

■If you have routed the Ethernet cable through the center opening, secure the cable on the

hook located on the mounting plate as shown in the illustration below.

2Connect the Ethernet cable to the Ethernet port on the access point.

3Connect the power cable to the power port on the rear panel of the access point.

4Position the access point at an angle to the mounting plate bayonet connection and turn the

unit clockwise until it snaps into place, as shown below.

6 Flat Surface Installation

1Find a clean and dry surface that is elevated enough to provide good reception and coverage

for the network. Do not place the access point on a metal surface.

2Make sure to choose a location where the access point will not be disturbed.

3Connect the Ethernet cable into the Ethernet port.

4Connect the power cable to the power port on the rear panel of the access point.

5Set the access point down on a flat, level surface.

Radio

Ethernet

Power

Top opening

Center opening

Hook for securing

the cable

Align with mounting plate

and rotate clockwise to lock

7 Antenna Adjustment

Position the antennas so that they turn away from the access point at approximately a 45-degree angle. Your

particular location might require additional antenna adjustment.

8 Documentation and Software Utilities

The installation CD includes documentation and software utilities to help you set up and administer the wireless

components of your network. To view product documentation, select View the Documentation from the CD

Startup Menu and then select the item you wish to view. To install utilities, select Tools and Utilities from the

CD Startup Menu. Select the items you wish to install and follow the onscreen instructions. The software Tools

and Utilities include:

■3Com Wireless Infrastructure Device Manager. Use this tool to discover access points and

select devices for administrative changes. Uninstall any previous versions before installing

this version.

■3Com 3CDaemon Server Tool. This tool can act in four different capacities:

■As a TFTP Server, necessary for firmware upgrades, and backup and restore functions.

Use this option if you do not have a TFTP server set up.

■As a SysLog Server, which is necessary to view SysLog messages.

■As an optional TFTP Client.

■As an optional FTP Server.

■3Com Network Supervisor. The 3Com Network Supervisor (3NS) graphically discovers,

maps, and displays network links and IP devices, including 3Com wireless access points. It is

not required for access point management.

■3Com Site Survey Tool. This utility assists in selecting the best location for your access point

before installing the device permanently. Use the Site Survey Tool to determine if the

intended mounting locations will provide adequate coverage with good signal strength and

quality.

■Internet Explorer 5.5. This browser is included for those who do not have a

suitable browser.

CAUTION: Do not handle the antenna tips, especially after they are connected to the access

point, as this could lead to electrostatic discharge (ESD), which could damage the equipment.

trademarks of 3Com Corporation. All other company and product names may be trademarks of the respective

companies with which they are associated.

09-2340-000 Rev AA

Published December 2003

9 Configuration Notes

■For a new access point installation, the default WLAN Service Area (ESSID) is 3Com and no

security is set. Unless it detects a DHCP server on the network, the access point uses Auto IP

to assign an IP address of the form 169.254.2.1.

■Use the 3Com Wireless Infrastructure Device Manager to locate 3Com Wireless LAN devices

and launch their configurations. When installing the device manager, make sure the computer

is connected to the same network as the device to be configured. The default login is “admin”

and there is no password. After installing and launching the device manager, select the device

to be configured from network tree and click Configure to launch the configuration Web

interface. Refer to the Access Point 7250 User Guide (included on the installation CD) for

detailed information and instructions on locating and configuring the access point.

■The first time you connect to this device, you will need to specify how the device obtains its

IP address; for most installations we recommend that you select “Obtain the setting

automatically from a DHCP server.” For more information, see your network administrator.

■Once you have logged onto the device, we strongly recommend changing the default

password. You can find password settings in the administration menu.

■If you experience difficulty with the installation, see the Troubleshooting section of the

User Guide.

For the latest information, see the 3Com Corporation World Wide Web site: http://www.3com.com/.

Table des matières

Autres manuels 3Com Point d'accès sans fil

3Com

3Com AP9552 Manuel utilisateur

3Com

3Com OfficeConnect Manuel utilisateur

3Com

3Com 3CRWE20096A - Wireless LAN Access Point 2000 Manuel utilisateur

3Com

3Com AirProtect Sensor 5750 Manuel utilisateur

3Com

3Com 8760 - Wireless Dual Radio 11a/b/g PoE Access... Manuel utilisateur

3Com

3Com 3950 Manuel utilisateur

3Com

3Com AP9552 Manuel

3Com

3Com AP3850 Manuel utilisateur

3Com

3Com MAP 2750 Manuel utilisateur

3Com

3Com AP9152 Manuel utilisateur

3Com

3Com 8250 Manuel utilisateur

3Com

3Com OfficeConnect 3CRWE454A72 Manuel utilisateur

3Com

3Com 3CRGPC10075 Manuel utilisateur

3Com

3Com AirConnect 9550 Manuel utilisateur

3Com

3Com 8200 Manuel utilisateur

3Com

3Com 3CRWEASYA73 / WL-575 Manuel utilisateur

3Com

3Com LANplex 6000 Manuel utilisateur

3Com

3Com Wireless 11n USB Adapter Manuel utilisateur

3Com

3Com 3CRWE876075 / WL-546 Manuel utilisateur

3Com

3Com Wireless LAN 11 Mbps Manuel utilisateur

3Com

3Com WL-306 Manuel utilisateur

3Com

3Com 3CRWE920G73 Manuel utilisateur

3Com

3Com OfficeConnect 3CRWE454G75 Manuel utilisateur

3Com

3Com 3CRWX395075A - Wireless LAN Managed Access Point... Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur