3Com 3C2000 Manuel utilisateur

3Com Gigabit Network Interface Card

3C2000

User Guide

http://www.3com.com/

http://support.3com.com/registration/frontpg.pl

Published April 2003

User guide version 1.0

3Com Corporation •5500 Great American Parkway •Santa Clara, California •95052-8145 •U.S.A.

to make any derivative work (such as translation, transformation, or adaptation) without written permission from 3Com Corporation.

3Com is a registered trademark and the 3Com logo is a trademark of 3Com Corporation. Unless otherwise indicated, 3Com registered

trademarks are registered in the United States and may or may not be registered in other countries.

Intel and Pentium are registered trademarks of Intel Corporation. Marvell, Virtual Cable Tester (VCT) and the Marvell logo are registered

trademarks of Marvell. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Novell and NetWare are

registered trademarks of Novell, Inc. All other company and product names may be trademarks of the respective companies with which they

are associated.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time without obligation on the

part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or expressed, including, but not

limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. 3Com may

make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license agreement included with the product

as a separate document, in the hard copy documentation, or on the removable media in a directory file named LICENSE.TXT or !LICENSE.TXT.

If you are unable to locate a copy, please contact 3Com and a copy will be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are provided to you subject to the

following:

All technical data and computer software are commercial in nature and developed solely at private expense. Software is delivered as

“Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item” as defined in FAR 2.101(a) and as

such is provided with only such rights as are provided in 3Com’s standard commercial license for the software. Technical data is provided with

limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or FAR 52.227-14 (June 1987), whichever is applicable. You agree not to

remove or deface any portion of any legend provided on any licensed program or documentation contained in, or delivered to you in conjunction

with, this user guide.

Contents

1 Introduction 1

2 Installing and Connecting the NIC 3

3 Windows XP Driver Installation 9

4 Windows 2000 Driver Installation 13

5 Windows Me Driver Installation 17

6 Windows 98 SE Driver Installation 21

7 Windows NT 4.0 Driver Installation 25

8 Linux Driver Installation 29

9 Novell NetWare Driver Installation 31

10 Installing and Using the 3Com Connection Assistant 37

11 Using the Virtual Cable Tester 39

12 Troubleshooting 41

A Specifications 45

B Technical Support 47

C Warranty Information 51

D Regulatory Information 53

Contents

Introduction

This guide describes how to install and configure the 3Com®3C2000 Gigabit Network

Interface Card (NIC) in the following operating system (OS) environments:

•Windows XP

•Windows 2000

•Windows Millennium Edition (Me)

•Windows 98 SE

•Windows NT 4.0

•Linux 2.4

•Novell NetWare 5.1 and 6.0

Package Contents

•3Com 3C2000 Gigabit NIC

Keep the NIC in its package until ready for installation.

•3Com Installation CD with driver software and user guide

If the Windows autorun feature is enabled on your system, the

3Com Master Navigator launches automatically when you insert the

3Com Installation CD. See “Using the Master Navigator” on page 6 for more

information.

NOTE: Inform your network supplier of any missing or damaged items. If you

need to return the NIC, you must use the original (or equivalent) packaging.

1 Introduction

Installing and Connecting the NIC

Before installing the NIC, make sure your PC meets the requirements listed below.

Hardware Requirements

•Pentium-based PC that meets software requirements for the following operating

systems:

•Windows XP with latest service pack

•Windows 2000 with latest service pack

•Windows Me with latest service pack

•Windows 98 SE with latest service pack

•Windows NT 4.0 with latest service pack

•Linux 2.4

•Novell NetWare 5.1 or 6.0

•One open PCI slot

•PCI v2.2 33/66 MHz

•128 MB RAM (minimum)

Safety Precautions

Observe the following safety precautions.

WARNING: The NIC is being installed in a system that operates with voltages

that can be lethal. Before you remove the cover of your system, you must

observe the following precautions to protect yourself and to prevent damage to

the system components:

•Remove any metallic objects or jewelry from your hands and wrists.

•Use only insulated or nonconducting tools.

•Verify that the system is powered off and unplugged before removing the

cover.

•Install or remove the NIC in a static-free environment only. The use of a

properly grounded wrist strap (or other personal anti-static device) and an

anti-static mat are strongly recommended.

2 Installing and Connecting the NIC

Pre-Installation Checklist

1Check that your system meets the hardware and software requirements listed

under “Hardware Requirements” in the previous section.

2Verify that your system is using the latest BIOS.

3Review the information in the readme.txt file on the 3Com Installation CD for

important information not available at the time this user guide was created.

4If your system is active, shut it down.

5When shut down is complete, turn the power off and unplug the system.

6Holding the NIC card by the edges, remove it from its shipping package and place

it on an anti-static surface.

7Check the NIC for visible signs of damage, particularly on the edge connector.

Never attempt to install any damaged NIC. If the NIC is damaged, report it to your

supplier.

Installing the NIC

1Review the safety precautions and pre-installation checklist.

2Before installing the NIC, ensure the system power is off, the system is unplugged

from the power outlet, and that proper electrical grounding procedures have been

followed.

3Remove the system cover, and select any empty PCI slot. If you do not know how

to identify a PCI slot, refer to your system documentation.

4Remove the blank cover plate from the slot that you selected.

5Holding the NIC by the edges, align the connector edge of the NIC with the PCI

connector dock.

6Applying even pressure at both corners of the NIC, push the NIC until it is firmly

seated in the PCI slot.

When properly seated, the port connector on the NIC will be aligned with the slot

opening, and its faceplate will be flush against the system chassis.

7Secure the NIC in the PCI slot.

8Replace the system cover, disconnect any personal anti-static devices, and plug

the system back in.

9Turn the system power on.

After the system returns to normal operation, the NIC hardware is fully installed.

The next step is to connect the network cable.

CAUTION: Do not use excessive force when seating the NIC, as this may

damage the system or the NIC. If the NIC resists seating, remove it from the

system, realign it, and try again.

Connecting the Network Cable

The NIC has one RJ-45 connector for attaching it to an Ethernet copper-wire segment.

When automatic link negotiation is disabled, the port can be configured for 10 Mbps or

100 Mbps signaling at either half-duplex or full-duplex operation, as well as 1000 Mbps

signaling at full-duplex operation.

To connect a network cable to the NIC:

1Prepare an appropriate cable.

The following table lists the cable characteristics for connecting to

10/100/1000BASE-T ports:

2Connect one end of the cable to the NIC.

3Connect the other end of the cable to an RJ-45 Ethernet network port.

The next step is to install the NIC driver and software.

Installing NIC Software

This section describes how to install the NIC driver and software in Windows using

the 3Com Master Navigator.

1Insert the 3Com Installation CD.

The Master Navigator launches automatically. If it does not launch, run

LAUNCH.EXE from the 3Com Installation CD.

2Select NIC Software, and then follow the prompts on the screen.

Port Type Connector Media Maximum Distance

10BASE-T RJ-45 CAT 3, 4, or 5 UTP 100 meters (325 feet)

100BASE-T RJ-45 CAT 5 UTP (two pair) 100 meters (325 feet)

1000BASE-T RJ-45 CAT 5/CAT 5e (four pair) 100 meters (325 feet)

NOTE: 1000BASE-T signaling requires four twisted pairs of Category 5

balanced cabling, as specified in ISO/IEC 11801:1995 and EIA/TIA-568-A

(1995) and tested using procedures defined in TIA/EIA TSB95.

NOTE: For driver installation and configuration instructions on non-Windows

operating systems, or if you do not want to use the 3Com Master Navigator,

refer to the software configuration chapter for that specific driver.

2 Installing and Connecting the NIC

Using the Master Navigator

When you allow the Windows autorun feature to launch the Welcome Screen of

the 3Com Master Navigator, you can select from the options listed below.

•User Guide

View, print, or copy the user guide.

The user guide is in Adobe Acrobat PDF format. You can also place a copy of the

user guide on your hard drive and place a link to it in the Windows Start, Programs

listing.

•NIC Software

Install your NIC or improve the performance, control, and management of your

current network.

NOTE: If the Windows autorun feature is not enabled, run LAUNCH.EXE

from the 3Com Installation CD.

NOTE: You must have Adobe Acrobat installed to view the user guide.

Table des matières

Autres manuels 3Com Carte réseau

3Com

3Com EISA 10/100BASE-T Manuel utilisateur

3Com

3Com EtherLink 3C985B-SX Manuel utilisateur

3Com

3Com HiPer DSP Manuel utilisateur

3Com

3Com Dual E3 Asynchronous Manuel utilisateur

3Com

3Com EtherLink 3C905C-TX Manuel utilisateur

3Com

3Com 3C905CX Manuel utilisateur

3Com

3Com EtherLink III ISA Manuel utilisateur

3Com

3Com TokenLink 3C359 Manuel utilisateur

3Com

3Com 3CSOHO100- Manuel utilisateur

3Com

3Com III ISA Manuel utilisateur

3Com

3Com EtherLink 10 Manuel utilisateur

3Com

3Com Remote Network Adapter Manuel utilisateur

3Com

3Com Etherlink 100 PCI Manuel utilisateur

3Com

3Com TokenLink 3C339 Manuel utilisateur

3Com

3Com TokenLink 3C359B Manuel utilisateur

3Com

3Com OfficeConnect 3CSOHO100-TX Manuel utilisateur

3Com

3Com TokenLink 3C359 Mode d’emploi

3Com

3Com 09-0572-000 Manuel utilisateur

3Com

3Com Fast EtherLink 3C515-TX Manuel utilisateur

3Com

3Com 3C905C-TX-M Manuel utilisateur

3Com

3Com Server Manuel utilisateur

3Com

3Com EtherLink XL 10 Manuel utilisateur

3Com

3Com 7600 Manuel utilisateur

3Com

3Com TokenLink Velocity TokenLink VelocityTM XL PCI Network Interface... Manuel utilisateur

Manuels Carte réseau populaires d'autres marques

FirstComm

FirstComm OBiWiFi5G Manuel utilisateur

Sun Microsystems

Sun Microsystems Interface Adapter Manuel utilisateur

TRENDnet

TRENDnet TU2-ETG Manuel utilisateur

YASKAWA

YASKAWA SI-EN3 Manuel utilisateur

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuel utilisateur

Belkin

Belkin F5D7050 Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITX Manuel utilisateur

Cisco

Cisco MC16E Manuel utilisateur

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuel utilisateur

TwinMOS

TwinMOS Booming Manuel utilisateur

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur

National Instruments

National Instruments NI 9234 Manuel utilisateur

Hama

Hama 49276 Manuel utilisateur

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation

Compaq

Compaq Wireless LAN 100 Manuel utilisateur

Bose

Bose PowerMatch Dante Manuel utilisateur

TRENDnet

TRENDnet TEG-PCITXR Manuel utilisateur