360 Yield 360 Y-DROP APACHE Manuel utilisateur

INSTRUCTIONS

360 YDROP®

APACHE

360 Y-DROP®REGISTRATION

Please visit productregistration.360yieldcenter.com

to complete the product registration for your

360 Y-DROP so we can better support our products

from day one and ensure you have the latest

upgrades, warranty parts and technical support.

Thank you!

360YIELDCENTER.COM

V1  11.30.2016

INSTRUCTIONS

360 YDROP

APACHE

INTRODUCTION

Before beginning, it’s important to know where each mounting bracket ﬁts relative

to the row spacing involved. The 360 Y-DROP unit should be precisely centered

on the machine, as this is critical to the assembly of the system to the sprayer and

for mounting the system to your sprayer boom. There are, however, many boom

variations among all sprayer models. Your sprayer may not be identical to the model

in the following steps of the guide, and the pictures may not exactly reﬂect your

model. While these steps will help you install most of your 360 Y-DROP system,

you may need to custom-ﬁt some components with your particular boom.

RECOMMENDED TOOLS

Ratchet wrench with 1/2" and 9/16" deep well sockets

3/8" 12-point socket

1/2" and 9/16" combination wrenches

#2 Phillips screwdriver (for the shield installation)

TORQUE VALUES

Refer to these torque values when tightening all fasteners

5/16" stainless U-bolt 15 ft/lbs

5/16" stainless Set screw 15 ft/lbs

3/8" carbon U-bolt 35 ft/lbs

5/16" carbon U-bolt 30 ft/lbs

5/16" carbon Stop bolt 30 ft/lbs

QUESTIONS

Call our Product Support team at 888-512-4890

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

ESTABLISH

DROP LOCATIONS

Figure 1

Step 1 Locate the center of the machine and

identify the location of all the drops. On

the sprayer boom, mark where each riser

mount will be located. This will ensure

that the extension tubes will not interfere

with the riser mounts.

Figure 2

Step 2 For the primary boom; starting at the

wing fold pivot pin, measure out and

make marks at 28", 89", 152", 212"

and 257" (all measurements are ±5").

Repeat for the other primary boom.

Figure 1

Figure 2

28"

89"

152"

212"

257"

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL MOUNT ASSEMBLIES

ON THE OEM PRIMARY BOOM

Figure 3

Step 1 With the threads pointing down, install

U-bolt (1) on the top of the OEM

primary boom.

Bag AF

Step 2 Install bracket assembly (2) and ﬂange

lock nut (3).

Hardware Kit D

Step 3 Install extension tube (4).

Figure 4

Step 4 Install boom bracket (1) onto the

extension tube.

Step 5 Install stop bolts (2) at both the front

and the rear of the extension tube.

Hardware Kit B

Figure 5

Step 6 Install stainless steel set screw and

jam nut assembly (1) onto the bracket

assembly.

Hardware Kit D

Repeat Steps 1-6 for the remaining mount assemblies

on the OEM primary boom.

II.

Figure 3

Figure 4

Figure 5

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL MOUNT ASSEMBLIES

ON THE OEM PRIMARY BOOM CONTINUED

Figure 6

Step 7 With the U-bolt pointing to the rear,

install the yoke mount (1) and ﬂange

nuts to upper boom section.

Step 8 With the square U-bolt threads pointing

up and using the extra thick washer and

Nylock nut, install yoke mount (2) to the

360 Y-DROP boom section.

Step 9 Using pins, install the yoke straps (3)

between the upper boom and 360

Y-DROP boom. Using the ﬂange nuts,

tighten the 1-1/4" carriage bolts.

Repeat Steps 7-9 for the remaining yokes on

the OEM primary booms. Yokes should be spaced

approximately 60" (±5”) apart.

II.

Figure 6

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL CENTER SECTION

SQUARE TUBE

Figure 7

Step 1 Install u-bolt (1) and 14" top

plate (2) using the supplied hardware.

Step 2 Install bracket assemblies (3).

Figure 8

Step 3 Install extension tube (1).

Step 4 Install 360 Y-DROP boom bracket (2)

on extension tube (1).

Bag BB

Step 5 Install stop bolt assemblies (3).

Hardware Kit B within Bag BB

Step 6 Install set screws (4) on bracket

assemblies.

Hardware Kit D within the Center Section Kit

Figure 9

Step 7 Install set screw (1) on Y-DROP boom

bracket.

Hardware Kit D within the Center Section Kit

NOTE: There are three mounting locations for the

Apache Sprayer Mount Package.

Repeat steps 1-7 for the remainder of the

center section square tube.

III.

Figure 7

Figure 8

Figure 9

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL 360 YDROP

BOOM

Figure 10

Step 1 Assemble 5' boom sections (1) using the

8" boom connectors (2) and the supplied

hardware.

Hardware Bag CC

Step 2 Repeat Step 1 as needed in order to

assemble the entire 360 Y-DROP boom.

Step 3 Set the 360 Y-DROP boom assembly

onto boom bracket (3).

Repeat Steps 1 -3 for the remaining boom assemblies.

CAUTION: The 360 Y-DROP boom assembly may

weigh up to 150 lbs. (68 kg). Exercise caution and

enlist help for this process.

Figure 11

Step 4 In order to span the full length of the

center section 360 Y-DROP boom, you

will need to cut and drill one of the 5'

boom sections to 1'. Mount this 1' section

between two full 5' boom sections. Drill a

7/16" through hole centered 2" from the

outside edge.

Figures 12 and 13

Step 5 Install square U-bolt (1), the 5/16" extra

thick washers, and the 5/16" nuts over

the 360 Y-DROP boom (2).

Hardware Kit A

Step 6 Install stop bolt (3) at both the front and

the rear of the extension tube. Repeat for

remaining stop bolts.

Hardware Kit B

Step 7 Install stainless steel set screw and

jam nut assembly (4). See Figure 13 for

detail. Repeat for the remaining mount

assemblies on the primary boom.

IV.

Figure 10

Figure 11

Figure 12

Figure 13

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL BREAKAWAY ASSEMBLY 

ONE PIECE

Figure 14

Step 1 Install breakaway assembly - one piece (1)

using the square U-bolts (2) and the extra

thick washer and Nylock nut. Repeat for

the remaining breakaway assemblies -

one piece.

Hardware Kit C

NOTE: The alignment and quantity of the mounts

will depend on your row spacing.

Figure 15

Step 2 Install riser tube assembly (1) into the

breakaway assembly - one piece (2).

Step 3 Install pin (3).

Repeat Steps 2 and 3 for the remaining riser tube

assemblies.

NOTE: Included in most sprayer mount packages

are standard riser mounts to be used when primary

booms are folded and in transport mode. These

standard riser mounts should be mounted in

locations that allow you to relocate the drops away

from potential tire interference. See “Install Riser

Mounts Without Breakaway Assemblies” section on

next page for more instructions.

Figure 14

Figure 15

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

INSTALL RISER MOUNTS WITHOUT

BREAKAWAY ASSEMBLIES (OPTIONAL)

Figure 16

Step 1 Install riser mount (1) using the square

U-bolts (2) and the extra thick washer

and Nylock nut. Repeat for the remaining

riser mounts.

Hardware Kit C

NOTE: The alignment and quantity of the riser

mounts will depend on your row spacing.

Figure 17

Step 2 Install riser tube assembly (1) into the

riser mount (2).

Step 3 Install pin (3).

Repeat Steps 2 and 3 for the remaining riser tube

assemblies.

Figure 17

Figure 16

INSTRUCTIONS 360 YDROP

APACHE

360YIELDCENTER.COM

Figure 18

Figure 19

Figure 20

INSTALL SHIELDS AND

RISER HOSES

Figure 18

Step 1 Install shield (1) onto riser tube (2).

Figure 19

Step 2 Install base unit (1) onto riser tube (2).

Figure 20

Step 3 Assemble drag hoses (1) to 360 Y-DROP

base and secure with hose clamps (2).

Figure 21

Step 4 Note the orientation of the drag hose

clamps. The tails should point inward.

VI.

Figure 21

Table des matières

Autres manuels 360 Yield Matériel agricole

360 Yield

360 Yield 360 Y-DROP JOHN DEERE 4930 Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP MILLER Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP HAGIE DELTA BOOM Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP JOHN DEERE 4720 Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP HAGIE DTS 2016 + Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP HAGIE ALUMINUM BOOM Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP ROGATOR Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP CASE 120 BOOM Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP HAGIE STS 80 Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP JOHN DEERE 4730 Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP JOHN DEERE 4630 Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP JOHN DEERE R SERIES Manuel utilisateur

360 Yield

360 Yield 360 Y-DROP JOHN DEERE 4710 Manuel utilisateur

Manuels Matériel agricole populaires d'autres marques

GSi

GSi PNEG-2314 Manuel utilisateur

Checchi & Magli

Checchi & Magli TEXDRIVE Manuel utilisateur

Amazone

Amazone Cenius 4003-2TX Manuel utilisateur

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manuel utilisateur

Cima

Cima BLITZ Instructions d'utilisation et d'entretien

Amazone

Amazone CombiDisc 3000 Instructions d'installation

HE-VA

HE-VA Disc-Roller XL Contour Manuel utilisateur

AGT

AGT AGT-SSFM Manuel utilisateur

Milestone

Milestone 72-84 Manuel utilisateur

KUHN

KUHN Hector 3000 Manuel utilisateur

Krone

Krone X-Disc 6200 Manuel utilisateur

Eliet

Eliet DZC450 Manuel utilisateur

Taarup

Taarup BIO+ B4000 Manuel utilisateur

Garland

Garland SHAKER 310 DPG Manuel utilisateur

stable comfort

stable comfort StableWall System Manuel utilisateur

Raven

Raven AccuBoom Manuel utilisateur

International

International 710 Manuel utilisateur

Ashland

Ashland HDW-3217-14 Manuel utilisateur