Zzipp ZZONE2120PA Manuel utilisateur
USER MANUAL
MANUALE D’USO
MANUAL DE USUSARIO
ZZONE2120PA
MIXER - AMPLIFICATORE - LETTORE MP3 / FM / BLUETOOTH A 2 ZONE
2 ZONE MIXER AMPLIFIERS WITH MP3 / FM / BLUETOOTH
AMPLIFICADORES MEZCLADOR 2 ZONAS CON MP3 / FM / BLUETOOTH
ENGLISH ITALIANO ESPANOL
2
Transport the product only using the handles. Don’t shake it.
To avoid the risk of fire or shock do not expose the product to rain or direct and excessive
humidity. If the environment is much colder than the temperature of this product, wait for
it to adjust to room temperature before turning it on. Do not use the product for permanent
installations. Only connect the product to circuits grounded and protected.
Always disconnect it from the power supply before cleaning it or replacing the fuse.
Replace the fuse with another of the same type and the same rated voltage.
Do not clean the product with solvents or aggressive detergents. Use a soft, clean cloth.
Before connecting the product to a power supply, make sure the cable of power supply is
not damaged.
Make sure that the voltage of the electrical outlet is within the range indicated on the
product (on the housing or on a sticker).
Never disconnect the product from the socket by pulling the cord.
Always make sure that the product is used in a location with adequate ventilation with
at least 50 cm of space from adjacent surfaces. Make sure that none of the ventilation
openings are obstructed.
Do not use the product at temperatures above 104 ° F / 40 ° C.
Keep flammable materials away from the product during use.
Do not touch the product when it is switched on or immediately after switching off. The
product and its housing can reach high temperatures.
If you experience serious problems while using the product, stop using it immediately.
Do not open the product housing. Contains parts that cannot be repaired by the user and
such opening would void the warranty.
Thanks for purchasing this ZZIPP product, please read this instruction carefully to
understand how to operate the product correctly. Please store this instruction in a safe
place after reading as a reference in the future.
To reduce the risk of electric shock, do not remove the cover or the side.
Always contact qualified personnel for repairs.
To reduce the risk of fire and electric shock, do not expose the appliance to moisture and
direct contact with liquids.
SAFETY INSTRUCTIONS
ENGLISHITALIANOESPANOL
3
The ZZONE2120PA is 2 zone mixer amplifier is designed for 19” rack mount installation
or tabletop use both application, it is ideal for both professional sound system and
commercial audio solutions, since it is designed with 2 zone speaker outputs support 100V
& 8-16Ω. The ZZONE2120PA series mixer amplifier integrates two 100V & 8 Ω amplifier
into one unit, so it could be used as stereo mixer amplifier or 2 zone commercial mixer
amplifier. The mixer amplifier is built-in media player of USB/SD/FM/ & Bluetooth, with 3
mic inputs, line input, EMC input, 6 units 2 zone remote paging mic ZZONE2120PA and 6
units remote panel and one mute input. 3 Mic/line switchable inputs, 1 aux input and an
integral USB/SD/FM audio player with Bluetooth receiver can be matrix switched to any of
the 2 zones independently. Mic1 channel with VOX highest priority and each microphone
1-3 inputs have switchable +48V phantom power. A master chime with volume can be
used for paging calls and Alerts. The 2 zone mixer amplifier is designed for multi-
room commercial audio systems requiring different audio sources & multiple paging
microphones, additionally, up to 8 units of remote microphones and 2 units 2 zone remote
control panes could be connected to this 2 zone mixer amplifier through CAT6 cable ,
which could be installed in two separate rooms to select different audio sources locally
and adjust the local loudspeaker loudness and input Bluetooth to its own room. The mute
input could integrate with fire alarm system or other third party system. The amplifier is
designed with complete protection includes short-circuit, clip, overload and high temp.
FEATURES
DESCRIPTION
• Desktop or 19” rack mount 2 zone public address 2 zone mixer amplifier
• 2 Zone Mixer Amplifier built-in medial player with USB/SD/FM/ & Bluetooth
• Rate power output at 2×120W, 2×240W, 2×350W to 2×500W
• 2 zone separated speaker output of 100V & 8-16Ω
• Each input with zone 1 or zone 2 output selector on front panel
• Each zone output with volume +, volume- and mono control on front panel
• 3 x Mic/line inputs, 1 x RCA line input, 1 x RCA EMC input and 1 x mute input
• Mic/line inputs1-3 of Combo type with switchable +48V phantom power
• With emergency remote mute input
• Input priority level from high to low: Mute, EMC, Mic1 and remote paging mic to
others inputs.
• Each amplifier support 8 units 2 zone remote microphones PA-2500RM through
CAT6 cable
• Each amplifier support 2 units 2 zone remote control panels PA-2500SV through
CAT6 cable
• With short-circuit, clip, overload and high temp protection
ENGLISH ITALIANO ESPANOL
4
FRONT PANEL
REAR PANEL
1. Mp3/FM/Bluetooth media player.
2. MP3 output zone 1-2 selector
3. Mic2-4 & Aux output attenuator
4. Zone 1 output volume attenuator and
Mono selector
5. Zone 2 output volume attenuator and
Mono selector
6. Chime button and chime volume
attenuator
7. Power supply on/off indicator
8. Mic2-4 & Aux output selector to
Zone1-2
9. Power switch
1. AC Power Socket with removable fuse
2. Zone1-2 output-100V (- & + terminals)
3. Zone1-2 output-8-16 Ohm (COM & 8-16
4. Line output
5. Monitor output
6. EMC input from fire alarm system with
priority except MUTE input (11)
7. Stereo line or Aux input
8. Mic/line input of COMBO input for both
XLR and 6.3mm jack
9. Dipswitch of 2 PIN. Mic/line selector and
+48V phantom power on/off selector.
10. RJ45 ports for remote microphone and
remote control panel.
11. Mute input, open circuit to activate mute
of highest priority and closed circuit
back to amplifier normal working status.
12. FM antenna
13. Mic2-4 & Aux input bass & treble gain
control.
ENGLISHITALIANOESPANOL
5
CONNECTION AND SETUP
DIP SWITCHES
PRIORITY AND EMERGENCY ACTIVATION
SINGNAL INPUTS AND OUTPUTS
With the ZZONE2120PA power switched off (20), connect the rear IEC inlet (21) to the mains
using the supplied mains lead (or an equivalent approved type). Ensure that the voltage
is correct and the speaker connect is correct then power on The ZZONE2120PA has 5
input channels and an integral multi-source audio player. Microphone input 1, 2 and 3 are
designed for either microphones or line level sources (such as a CD/mp3 player or output
from a mixer) via combo connectors on the rear panel, it is switch able by DIP switch. These
can accept either XLR or 6.3mm plugs for balanced or unbalanced signals.
Mic/Line inputs 1, 2 and 3 each have 2 DIP switches on the rear panel to set the input level
and/or activate +48V phantom power for use with condenser microphones.
Set the level correctly for the type of input source connected (Mic or Line) If the source
connected is a condenser microphone which requires phantom power, make sure that the
phantom is switched on for that channel.
Be sure to make these DIP switch settings when the amplifier is switched off. Making any
changes when the amplifier is powered up may cause loud bangs through the system which
can damage the speakers.
Connect microphones or line signals to Mic/Line 1, 2 and 3 inputs using good quality signal
leads. A stereo or mono line level source can be connected to the Auxiliary channel 4 input
on 2 RCA connectors. For checking the output of any zone, an assignable Monitor output
can be connected to headphones from the front panel 6.3mm jack or as a line output (e.g.
to active speakers) from RCA connectors at the rear. Each zone output has a dedicated RCA
signal output on the rear panel, which can be connected to the line inputs of active speakers
or amplifiers. These are in addition to the speaker outputs detailed below. An antenna input
is provided on the rear panel for connection to an external aerial for FM tuning. There are
Bass and Treble volume control on rear panel to adjust the sound of MIC and Line input
signal
1. Mute input, open circuit to activate mute of highest priority and closed circuit back to
amplifier normal working status.
2. EMC input- this one is EMC audio input of secondary priority
3. Mic1 input
4. Remote microphone ZZONE6000MC
SPEAKER OUTPUTS
The ZZONE6000PC has a separate speaker output for each zone, connected via 3 large
modular terminal plugs. Each plug can be removed from the rear panel for convenient
connection of speaker outputs to 2 zones. Each zone output can be used to power either
100V line speakers or standard low impedance speakers. These 2 configurations cannot be
used together, so it is important to decide which will be used at the start.
ENGLISH ITALIANO ESPANOL
6
100V LINE SYSTEMS
LOW IMPEDANCE SYSTEMS
For 100V speakers, connect the selected zone output to the first speaker in the zone using
double-insulated speaker wire which has adequate current rating to handle the total output
of the amplifier. Connect the “100V” output terminal for the selected zone to the positive (+)
connection of the speaker and “COM” output to the negative (-) connection of the speaker.
Connect further speakers in parallel to the first speaker with all positive terminals and
connected together and all negative terminals connected together as shown below.
Alternatively, each zone output of the amplifier is capable of powering one or more low
impedance speakers. There is an option on each zone for either a 8-16Ω speaker output
to determine the minimum impedance. It is essential to select the correct output terminal
when opting for low impedance speakers.
For a single 8Ω speaker, connect the positive (“+” 8-16Ω) wire to the (+) of speaker terminal
and the speaker negative (-) wire to “COM” of the amplifier terminals.
In either case, the connected load should have a combined impedance no lower than stated
on the terminal.
Lower impedance may cause irreparable damage to the amplifier.
The connected speaker(s) must also have a power handling to accept up to RMS loading
from the zone output. Lower power handling may risk damage to the speakers.
A 100V line speaker system can comprise of many speakers connected together. The
determining factor for how many speakers can be used on a single amplifier is the power
rating. For most purposes, it is advised to connect as many speakers as needed with a
combined wattage of no more than 80% of the amplifier’s output power rating (in the case of
the ZZONE2120PA, this is 120W per zone output)
The terminals of a 100V speaker are connected via a transformer and if necessary, this
transformer may be “tapped” for different power ratings. These tappings can be used to
adjust the wattage (and output volume) of each speaker in a zone to help achieve the ideal
total power of the system for the relevant zone output.
ENGLISHITALIANOESPANOL
7
OPERATION
ONBOARD MULTI SOURCE AUDIO PLAYER
LED DISPLAY MEANING
When all connections to the amplifier are made, turn all rotary controls down and switch on
the power and the power LED will illuminate.
To check for correct operation of the system, select an input source and output zone for
testing. In the following example, Mic/Line 1 input and Zone 1 output have been selected.
• Press Z1 button on the line of MIC/Line1, if zone1 display C2, that means MIC/Line1
output to zone 1
• If you playing MP3, press zone1 on the line of MP3, then zone 1 will have MP3 music and
display on Zone1 will show C1
If Zone 1 cannot be heard from the location of the ZZONE2120PA, use the monitoring feature
as follows
• Press the button of Monitor and connect headphones to the Monitor output
• Make sure that the Monitor button for Mic/Line 1 is pressed in and listen through the
headphones
• Gradually turn up the Monitor level control and check for the output to Zone 1
• C0-ZZONE6000MC
• C1-MP3 Module
• C2-MIC1/Line1
• C3-MIC2/Line2
• C4-MIC3/Line3
• C5-AUX
• C6-EMC
• C7-Local input
• C8-Mute
The ZZONE2120PA is fitted with a built-in audio player, operated via a backlit LCD display
and transport buttons. This section provides access to a Bluetooth™ receiver, FM radio tuner
and USB/SD audio player In order to play audio to one of the zones, it is necessary to press
in one of the “Play” buttons (4).
1. LCD Display
2. TF Slot
3. Mode: Select between Bluetooth, FM tuning,
USB or SD playback
4. Play: play music
5. Folder: hold on the music
6. RPT: repeat the music
7. Prev: Back to last music - Vol-: Reduce Volume
8. Next: go to next Music - Vol+: Increase volume
9. USB Slot
10. IR Receiver
Short press: Prev& Next
Long Press: Vol+&Vol-
ENGLISH ITALIANO ESPANOL
8
BLUETOOTH
FM TUNER
USB / SD PLAYER
2 ZONE REMOTE PAGING MICROPHONE ZZONE6000MC (OPTION)
In order to play back audio from a smartphone, tablet or other Bluetooth device, the built-in
Bluetooth receiver will need to be paired with a device which is within range.”
To pair a device with the ZZONE2120PA Bluetooth receiver, it is necessary to scan for devices
in the Bluetooth menu of the sending device and select to pair with “BT66078”. Once paired,
the ZZONE2120PA display will show it is connect, Password: 1234
Select to connect as an audio device and play audio tracks on the smartphone or tablet (or
other) and the audio should be heard on the selected zone. The buttons labelled “Prev” and
“Next” can adjust the audio player output volume. Press and hold “Prev” to increase volume
or press and hold “Next” to decrease volume. If the sending device goes out of range or the
Mode of the audio player is changed, the connection will stop. Returning to within range or
to Bluetooth mode will restore the pairing. It may be necessary to re-select connection as
an audio device on the sending device.
Press the Mode button to switch to the FM tuner function. For good FM reception, it will be
necessary to connect an external aerial to the Antenna connector on the rear panel using
good quality coaxial RF cable terminated. If no channels are tuned in, press the Play button
to begin auto tuning, which scans available stations and stores them as channels within
the ZZONE2120PA FM tuner. To step through pre-set stations, press the Previous or Next
buttons.
The ZZONE2120PA audio player has inputs for a USB pen drive or SD card with standard
compressed digital audio files on them. Inserting either or both of these will switch the
player to read from these sources and the display will show “MP3 Mode”. After you Insert
the USB it will play automatically, you can use “Prev” or “NEXT” to choose last or next song,
“REPT” is for one song or all song repeat.
• Communication through CAT6 cable up to 200M
• Direct power supply from matrix controller
• 2speaker zone individual group or all zone paging
• Up to 8 Mics working simultaneously loop connection
ENGLISHITALIANOESPANOL
9
REMOTE CONTROL PANEL (OPTION)
• Communication through CAT6 cable up to 200 ms
• Direct power supply from amplifier
• Audio sources selection and volume control
• 6 units capacity for each matrix controller
• Bluetooth Name: LOCAL, Password: 2018
1. The bottom box dial switch indicator
2. DIP switch
3. Terminal block
4. Terminal block (connected to host output network
cable 485-A)
5. Terminal block (connected to host output network
cable 485-B)
6. Terminal block (connected to host output network
cable AUDIO+)
7. Terminal block (connected to host output network
cable AUDIO-)
8. Terminal block (connected to host output network
cable +24V)
9. Terminal block (connected to host output network
cable GND)
ENGLISH ITALIANO ESPANOL
10
10. On the channel (output audio selection)
11. Bluetooth switch
12. Under the channel (output audio selection)
13. Display window
14. Volume plus
15. Volume reduction
CONNECTION DIAGRAMS
Table des matières
Langues :
Autres manuels Zzipp Amplificateur
