ZyXEL Communications QUICK START GUIDE G-3000H Manuel utilisateur

G-3000H

802.11g Wireless Access Point

Quick Start Guide

Version 3.50

11/2005

Table of Contents

ENGLISH 3

DEUTSCH 13

ESPAÑOL 25

FRANÇAIS 37

ITALIANO 47

繁體中文 59

ENGLISH

Overview

The ZyAIR G-3000H offers highly secured wireless connectivity to your wired network with IEEE 802.1x, Wi-Fi

Protected Access, WEP data encryption and MAC address filtering. This Quick Start Guide shows how to set

up and configure the ZyAIR to allow wireless clients to access your wired network. See your User’s Guide for

more information.

The following lists what you need to do:

1 Hardware Connections

Note: You may need your Internet access information.

1. Hardware Connections 4. Hardware Installation

2. Accessing the Web Configurator 5. Power over Ethernet (optional)

3. Internet Access Setup 6. Troubleshooting

ENGLISH

Do the following to make hardware connections for

initial setup.

1Using an Ethernet cable, connect the ETHERNET

port to a computer for initial configuration.

2Connect the POWER 12VDC socket to a power

source using only the included power adaptor for

your region.

Note: Connect the ZyAIR ETHERNET port to an

Ethernet jack with Internet access after you

have completed the initial configuration.

1.1 The LEDs

The PWR and the ZyAIR LEDs turn on when the power

is connected. The ETHN LED turns on, if the

ETHERNET port is properly connected.

See the ZyAIR Front Panel LED Description table in the

User’s Guide for more information.

2 Accessing the Web configurator

Use Internet Explorer 6.0 and later or Netscape

Navigator 7.0 and later versions with JavaScript

enabled.

ENGLISH

2.1 Set Up Your Computer’s IP Address

This section shows you how to assign your computer a static IP address in the 192.168.1.2 to 192.168.1.254

range with a subnet mask of 255.255.255.0. This ensures that your computer can communicate with your

ZyAIR. The following instructions are for the Windows 2000, Windows NT and Windows XP operating

systems.

1In Windows XP, click Start, Control Panel.

In Windows 2000/NT, click Start, Settings, Control Panel.

2In Windows XP, click Network Connections.

In Windows 2000/NT, click Network and Dial-up

Connections.

3Right-click Local Area Connection and then click

Properties.

4Select Internet Protocol (TCP/IP) (under the General

tab in Windows XP) and click Properties.

5The Internet Protocol TCP/IP Properties screen opens

(the General tab in Windows XP).

6Select Use the following IP address and fill in the IP

address (choose one from192.168.1.3 to

192.168.1.254), Subnet mask (255.255.255.0), and

Default gateway (192.168.1.2) fields.

7Click OK to close the Internet Protocol (TCP/IP)

Properties window.

8Click Close (OK in Windows 2000/NT) to close the

Local Area Connection Properties window.

Close the Network Connections screen.

ENGLISH

Note: Even though you can connect to the ZyAIR wirelessly, it is recommended that you connect your

computer to the ETHERNET port for initial configuration.

1Launch your web browser. Enter 192.168.1.2 (the

ZyAIR’s default IP address) as the address.

2Click Login (the default password 1234 is already

entered).

3Change the login password by entering a new

password and clicking Apply.

4Click Apply to create a certificate using your

ZyAIR’s MAC address that will be specific to this

device; alternatively click Ignore to proceed if you

do not want to change the certificate now.

ENGLISH

5Click WIZARD SETUP in the MAIN MENU screen.

3 Internet Access Setup

Use the setup wizard to configure your ZyAIR for wireless stations to access your wired LAN.

Note: Click Next in each screen to continue or click Back to return to the previous screen.

Your settings are not saved when you click Back.

1This screen is optional. You can just click Next.

2Use the second wizard screen to set up the wireless LAN.

System Name is for identifying the

ZyAIR. You can enter your

computer's "Computer Name".

Domain Name: Enter a domain name

if your ISP requires one for

authentication; otherwise you can

leave it blank or set to whatever may

have displayed automatically.

ENGLISH

Note: The wireless stations and ZyAIR must use the same SSID, channel ID and WEP encryption key

(if WEP is enabled) for wireless communication.

3Fill in the fields in the last wizard configuration screen.

Enter a descriptive name to identify the

ZyAIR in the wireless LAN.

Click Scan to have the ZyAIR

automatically select a channel and

display it in the Channel ID field.

Select 64-bit or 128-bit to encrypt data

frames before transmitting them over

the wireless network.

Select Disable to turn off WEP data

encryption.

Select ASCII or HEX WEP key input

method and then follow the on-screen

instructions to set up the WEP keys.

Click Next to continue.

If you have an IP address to use, select

Use fixed IP address and enter it

along with the subnet mask and

gateway IP address.

Click Finish.

Note: If you change the ZyAIR’s IP

address, you must use the

new IP address if you want

to access the web

configurator again.

ENGLISH

4Change the wireless parameter settings in the wireless stations to match those of the ZyAIR. Refer to your

wireless adapter’s documentation.

4 Hardware Installation

4.1 Attaching Antennas

Note: When facing the front of the ZyAIR, the right antenna (main antenna) transmits and receives, the

left antenna only receives.

Follow the steps below to connect the supplied antennas.

4.2 Hardware Mounting Installation

In general, the best location for the access point is at the center of your intended wireless coverage area. For

better performance, mount the ZyAIR high up free of obstructions.

This is the final wizard screen. You may

return to the MAIN MENU and continue

to configure your ZyAIR.

1Locate the antenna connectors on

the sides of your ZyAIR.

2Screw the antennas clockwise onto

the antenna connectors. The

antennas should be perpendicular

to the ground and parallel to each

other.

Note: Make sure the antennas are

securely screwed onto the

antenna connectors.

ENGLISH

Free-standing

Place your ZyAIR on a flat, level surface (on a desk or shelf) that is strong enough to support the weight of the

ZyAIR with connection cables.

Wall-mounted

Follow the steps to attach your ZyAIR to a wall.

1Locate a high position on the wall that is free of obstructions.

2Connect two screws (not included) in the wall 60mm apart. You can use the diagram at the end of this

guide to help you mark the screw holes correctly. Use screws with 6mm ~ 8mm (0.24" ~ 0.31") wide heads.

Do not screw the screws all the way in to the wall. Leave a small gap between the head of the screw and

the wall. The gap must be big enough for the screw heads to slide into the screw slots and the connection

cables to run down the back of the ZyAIR.

Note: Make sure the screws are securely fixed to the wall and strong enough to hold the weight of the

ZyAIR with the connection cables.

3Adjust the cables.

Run the connection cables down the back of the ZyAIR as shown in the following figure.

OR:

Run the connection cables upward and along the edge of the ceiling.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels ZyXEL Communications Point d'accès sans fil

ZyXEL Communications

ZyXEL Communications ZyAIR G-5100 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications nwa series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications P-2612HNU-Fx Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications WAP3205 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA1123 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA 1121-NI - Manuel utilisateur

ZyXEL Communications

ZyXEL Communications 100-NH Manuel utilisateur

ZyXEL Communications

ZyXEL Communications IES-6000 - ANNEXE 749 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA-1100 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA-1100 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-1000 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications WAP3205 v2 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyAIR G-5100 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ARMOR X1 WAP6806 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications WAC6103D-I Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-3000 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications WAP3205 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA-3165 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications VMG3926-B10A Manuel utilisateur

ZyXEL Communications

ZyXEL Communications NWA5120 Series Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyAIR G-3000H Manuel utilisateur

ZyXEL Communications

ZyXEL Communications G-570S Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyAIR G-3000H Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZyXEL ZyAIR B-1000 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur