ZooZ ZSE19 Manuel utilisateur
PAGE 1
ŸThis product should be installed indoors upon completion of any
building renovations.
SPECIFICATIONS
S2 MULTISIREN
ZSE19
www.getzooz.com
ask@getzooz.com
USER MANUAL
FEATURES
ŸAudio and visual alarm triggered by other Z-Wave devices
ŸConfigurable siren alarm duration
ŸBuilt-in temperature and humidity sensor (if Multilevel Sensor is supported)
ŸAudio Speaker for custom sound playback (if Sound Switch is supported)
ŸS2 security protocol and the latest 500 Z-Wave chip for faster and safer
wireless communication
ŸTamper protection, low-battery alerts
ŸModel Number: ZSE19
ŸZ-Wave Signal Frequency: 908.42 MHz
ŸPower: 4 x LR14 (C Cell) battery
ŸRange: Up to 100 feet line of sight
ŸOperating Temperature: 14-104° F (-10-40° C)
ŸOperating Humidity: 0-80%
ŸInstallation and Use: Indoor only
INSTALLATION
1. INSTALL THE BATTERIES
Locate the opening slot on the bottom of the back cover. Gently li the
cover and remove it to access the battery compartment. Follow the
orientation marks and insert the 4 batteries included in the box.
NOTE: The Multisiren can ONLY be
powered by batteries, it can’t be powered
from the USB port. This is only to upload
audio files to the device.
The LED indicator will start blinking and the Multisiren will enter auto-
inclusion mode for 30 seconds. It’s now ready to be added to your hub.
S2
WARNING
ŸPrior to installation, the device should be stored in a dry, dust-and-
mold-proof place.
ŸDo not install the device in a place with direct sun exposure, high
temperature, or humidity.
ŸKeep away from chemicals, water, and dust.
ŸEnsure the device is never close to any heat source or open flame to
prevent fire.
ŸEnsure the device is connected to an electric power source that does
not exceed the maximum load power.
ŸNo part of the device may be replaced or repaired by the user, except for
the batteries.
PAGE 2
MANUAL INCLUSION
2. POWER the siren
Z-WAVE CONTROL
TROUBLESHOOTING
1. ADD DEVICE to your hub (AUTO INCLUSION)
Initiate inclusion (pairing) in the app (or web
interface). Not sure how? ask@getzooz.com
If you’re using an S2 hub, it may ask you to enter
the DSK key printed on the back cover sticker to
complete secure inclusion.
Insert the batteries as instructed above (if you already
did, take them out for at least 15 seconds before
starting the inclusion process). The LED indicator will
start blinking and the Multisiren will join the network
automatically.
Put your Z-Wave hub into inclusion mode and click
the Z-Wave button 3 times quickly.
Get step-by-step instructions for adding
the siren to SmartThings, Vera, and
other hubs at ww.support.getzooz.com
The Multisiren won’t add to your system? Try this:
1. Initiate EXCLUSION and click the Z-Wave button 3 times quickly.
2. Click the Z-Wave button 4-5 times quickly when adding it or try
adding it in a non-secure mode.
3. Bring the Multisiren closer to your hub, it may be out of range.
4. Double-check if the device is powered.
1. Bring the Multisiren within direct range of your Z-Wave gateway (hub).
2. Put the Z-Wave hub into exclusion mode (not sure how to do that?
ask@getzooz.com).
3. Click the Z-Wave button on the Multisiren 3 times quickly to finalize
the process.
4. Your hub will confirm exclusion and the device will disappear from
your controller's device list.
EXCLUSION (REMOVING / UNPAIRING DEVICE)
FACTORY RESET
If your primary controller is missing or inoperable, you may need to reset
the device to factory settings. To complete the reset process manually,
make sure the Multisiren is powered, then CLICK-CLICK-CLICK-
CLICK’N’HOLD the Z-Wave button for AT LEAST 5 SECONDS. The LED
indicator will to confirm successful reset flash .
NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.
ADVANCED SETTINGS
Please refer to your controller's user guide for advanced programming
instructions as they are a little different for every soware.
Not sure where to start? Go to www.support.getzooz.com for detailed
instructions how to change the settings on SmartThings, Vera, and
more. Or just email us: ask@getzooz.com
All brand names displayed are trademarks of their
respective holders. © Zooz 2018
Z-WAVE
BUTTON
PAGE 3 PAGE 4
ASSOCIATION
This Multisiren supports Group 1 with up to 5 devices for lifeline communi-
cation. This device will send the following information to Group 1:
ŸNotification Report when it’s powered or when the tamper is triggered
ŸBattery Report when battery drops or is getting low
ŸDevice Reset Locally Notification aer factory reset
ŸSwitch Binary Report when siren is triggered or when it stops
ŸMultilevel Sensor Report for temperature and humidity data
CUSTOMIZE YOUR MULTISIREN
Siren Alarm Duration
Parameter 1: Choose how long you want the siren alarm to last for once it’s
triggered. The number entered as value corresponds to the number of
seconds.
Values: 10-600; 180 (seconds) – default value.
Size: 2 byte dec.
Temperature and Humidity Reporting Interval
Parameter 2: Choose how oen you want the Multisiren to report tempera-
ture and humidity readings to the hub. The number entered as value
corresponds to the number of minutes. Frequent reports will decrease
battery life.
Values: 1 – 1440; 30 (minutes) – default value.
Size: 2 byte dec.
Custom Sound Selection for Audio Speaker*
Parameter 3: Enable one of the custom sounds in the audio file library. The
number entered as value corresponds to the file number in the library (see
below for more details).
Values: 0 – 99; 0 – pause (default value).
Size: 1 byte dec.
*Audio Speaker is an optional feature enabled by the brand new Sound Switch command class. This
feature is separate from the siren alarm (the sound or volume of the siren can’t be adjusted) and
once fully enabled, it allows you to play different sounds from the library based on different Z-Wave
triggers and events. There’s a good chance your gateway controller (hub) doesn’t support this
command class yet and you won’t be able to use the Audio Speaker for now. But we’ve included it in
the documentation so you know it’s there once we finalize full integration with the major systems.
If you have any questions just email us: [email protected]om
How to manage the audio file library (for Audio Speaker only)
1. Plug the Multisiren to your computer/laptop using the mini USB port.
2. Follow the prompts on the screen to run the manager.
3. Use the file navigation menu on the le to locate your file source.
4. Select the files you want to upload to the Multisiren. Accepted formats:
Ÿ.wav files in Mono only (you need to convert any Mp3’s)
ŸSample rate: 8KHz – 32KHz
ŸMax length per file: 30 seconds (total max length of all files: 85 sec.)
5. Click on the upload icon in the bottom le corner on the window.
6. Your library is now updated. You can use the up/down arrow icons to
change the file order in the library. Note that the no. 2 file in the library
is reserved for tamper switch notification playback.
7. Close the Library Manager soware, remove the USB cable, and power
cycle your Multisiren by taking one of the batteries out and reinserting it.
Get detailed instructions, including screenshots, on how to manage
the library and to check if your hub supports the Audio Speaker
functionality at support.getzooz.com
This product can be included and operated in any Z-Wave network with
other Z-Wave certified devices from other manufacturers and/or other
applications. All non-battery operated nodes within the network will act as
repeaters regardless of vendor to increase reliability of the network.
This product features the latest Security 2 (S2) framework to remove smart
home network hacking risks. This device is equipped with a unique
authentication code for trusted wireless communication.
S2
WARRANTY
This product is covered under a 12-month limited warranty. To read the
full warranty policy or file a warranty claim, please go to
www.getzooz.com/warranty
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF
PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHE-THER IN AN
ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES.
ZOOZ'S LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN
CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED
ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE
PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF
THE PURCHASE PRICE FOR THAT POR-TION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE
CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE
OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30)
DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE
FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED
TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used according to instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may try to
correct the interference by taking one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from receiver
- Consult the dealer or an experienced radio/TV technician for additional assistance.
COMMAND CLASSES
AUDIO SPEAKER
(works with selected hubs)
SIREN ALARM
(works with most hubs)
This device requires the following command classes to be supported and
recognized by your Z-Wave controller:
COMMAND_CLASS_ZWAVEPLUS_INFO_V2
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_VERSION_V3
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2
COMMAND_CLASS_BATTERY
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_CONFIGURATION
COMMAND_CLASS_SENSOR_MULTILEVEL
COMMAND_CLASS_SOUND_SWITCH
MOUNTING
Mount the Multisiren in a vertical position around 6 feet from the ground
on a flat surface, possibly away from large metal objects which could
affect Z-Wave signal.
1. MARK HOLES
Use the back cover to mark 2 mounting
holes on a dry clean surface.
2. INSTALL BACK COVER
Drill holes and use the supplied anchors
and screws to fix the back cover to the wall.
3. MOUNT MULTISIREN
Slide the Multisiren down the back
cover and push it in to secure in place.
Ce manuel convient aux modèles suivants
1
Autres manuels ZooZ Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur