Zlin Aircraft Z-526 Akrobat Manuel utilisateur
SPECIFICATIONS
Wingspan:......................................1610mm
Length:...........................................1190mm
Electric Motor:.....................See next pager
Glow Engine:.................... .46 2-T / .70 4-T
Radio:....................7 Channel / 7 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps-Optional Retractable Landing Gear.
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio Control Model / Flugmodell
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
Instruction manual / Montageanleitung
TECHNISCHE DATEN
Spannweite:...................................1610mm
Lange:............................................1190mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:...............7.45cc - 11.5cc
Fluggewicht:.......................................3.2Kg
Fernsteuerung..........7 Kanal / 7 Servos
RTF Weight: 3.2Kg (will vary with equipment
use)
ZLIN
Z-526 Akrobat
1.5mm
AB
!
CA L/R Assemble left and right
sides the same way. X
Drill holes using the stated
size of drill
(in this case 1.5 mm )
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
CA
GLUE
Silicon sealer Cyanoacrylate Glue (thin type)
Minimum 7 channel radio
Extension cord for aileron servos: 50cm(x2)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately) Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the
model in a cool place will let the wrinkles disappear. Otherwise, remove
wrinkles in covering film with a hair dryer, starting with
low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten
entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie
zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden
Optional accessories. Please visit www.shop.pichler.de for more information
Low seting
BOOST 50 Brushless Combo Set
# C3173
LiPo Akku RED POWER 3500-14,8V # C9418
Extension cord for flap servos: 50cm(x4)
Extension cord for retract servos: 30cm(x2)
Extension cord for Rx battery pack: 20cm(x1)
EPOXY A
EPOXY B
Epoxy Glue
(30 minute type)
Standard Mini
Elevator : 1 standard servo
Rudder: 1 standard servo
Aileron: 2 mini servo
Flaps: 2 mini servo
Throttle: 1 mini servo (for glow engine only)
Empfohlenes Sonderzubehör.
Mehr Infos unter www.shop.pichler.de
1-Depending on the position of the linkage, determine the location of aileron control horn.
The horn holes must be perfectly aligned with the axis of articulation.
2-Mark the position of the “foot” of the horn on the aileron. Then, with the drill, make the 2
holes.
3-Install the aileron control horn as shown.
..........4
WING - BOTTOM VIEW
1-Cut away the covering of the wing bottom
where the aileron servo goes.
3-Install the aileron and flap servo on the servo mount.
-Switch on the radio (trims centered)
Then mount the ailerons servo horn
In neutral position.
-The servo horn should be
Perpendicular to the servo
YES NO
Do the same way with second wing half
....2
2x20mm....4
X
2 mm
Aileron pushrod
Adhesive
tape
2-Connect the aileron and flap servo cord to the
extension cords.
WING - BOTTOM VIEW
The rectangular hole on the bottom
of the flap is pre-cut at factory
Control horn Alignment
CA Thin CA
2x30mm
3mm
....2
EZ link
...4
ZLIN Z-526 1- Aileron and Flap servo
2- Aileron and Flap control horn
3- Aileron and Flap - Linkages
1
Aileron extension cord
exit hole
cut away only
the covering
WING - TOP VIEW
Keep the aileron extension cord
in place using sticker.
2
X
ZLIN Z-526 4- Extension cord secured
5- E-retract - Strut installation 3x15mm screw
...4 / not include
Ply gear mount
plate x 2
Gear mount x 2
Main landing gear
Gear mount
3x20mm
Nylon gear
strap
2mm
Ply gear
mount flat
Square
plastic
2mm
3x20mm screw
..........8
3x12mm screw
......16
Nylon gear strap
.......4
Square plastic
x 2
ZLIN Z-526 6- Decor 2x6mm screw
...........5
7- Fixed gear
AB
AB
Use epoxy glue to bury the
opening
1- Using a pencil, mark the center of the brace.
2- Trial fit the wing joiner into one of the wing panels. It should insert smoothly up to the center line marked above.
3- Slide the other wing half onto the dihedral brace until the wing panel meet. If the fit is over tight, it may be necessary to
lightly sand the dihedral brace.
4- Check for the correct dihedral angle.
5- Mix up some 30 minute epoxy and apply a generous amount of epoxy into the wing joiner cavity of one wing half.
6- Coat one half of the dihedral brace with epoxy up to the center line. Install the epoxy-coated side of the dihedral brace
into the wing joiner cavity up to the center line, marking sure that the “V” of the dihedral brace is positioned correctly
7- Do the same way with the other wing half.
8- Carefully slide the wing halves together, ensuring that they are accurately aligned. Firmly press the two halves
together, allowing the excess epoxy to run out. Clean off the excess epoxy with paper towel and kerosene.
Center line
Binder clip
Nylon wing bolt
Rubber band
(both the top
and bottom)
IMPORTANT: Please do not clean off the excess epoxy on the wing with strong solvent or pure alcohol, only use
kerosene to keep the colour of your model not fade.
75mm whell ...x2
4mm collar...4
ZLIN Z-526 8- Fixed gear
Top view
9- Joinning the wing halves
! Engine thrust on fire-wall
is already adjust at factory
FRONT-VIEW
- Remove the engine mount and drill a 13/64”
(5mm) hole through the fire-wall at each of the
four marks marked.
- Using a pencil or felt tipped pen, mark the
fire wall where the four holes are to be drilled
- Reposition the engine mounts on to the
fire-wall.
Secure them with four 4x25mm bolts
and blind-nuts.
! Align the mark on both mounts
with the mark on the fuselage
Pull the magnetic top hatch
out of the fuselage.
BB’
B=B’
5mm
13/64”
...4
.................4
4x25mm bolt
Blind-nut
5/32x1”
ZLIN Z-526 10- Engine
- Reposition the engine on to the engine mounts so
the distance from the prop hub to the fire wall is
132 to133mm.
- Remove the engine and drill a 1/8”(3mm) holes
through the beam at each of the four marks made
above.
- Reposition the engine on the engine mount beams,
aligning it with the holes. Secure the engine to the
engine mount using four 1/8x51/64”(3x25mm)
screws.
132 - 133mm
- Mark the engine mounting plate where the four
holes are to be drilled.
Note: Mark the mounting plate through the engine
mounting flanges.
3mm
3x20mm bolt
1/8”(3mm) nut
.................4
...4
1/8x5-1/64”
ZLIN Z-526 11- Engine
X
To muffler
Filler tube
To engine
3x25mm
screw
Rubber stopper
1
After confirming the direction . Insert this assembly, clunk end first, into the fuel
tank and tighten and screw the fuel tank cap on firmly.
3x35 mm screw 4mm
23
Ensure that the fuel tank clunk does not touch the rear of the fuel tank.
Checking for leaks - block the vents and blow
into the feed - if in doubt submersing the tank
in a blow of water will show up any problems.
Blow
Water
Carefully install the fuel tank to ensure that they will not
shift during flight (secure the fuel tank in place using
zip tie).
Cut of shaded portion
1.5mm
3mm
Prop. hub
2,5x10mm screw
...........5
ZLIN Z-526 12- Fuel tank
13- Cowling
-Using a aluminum motor mounting plate as a
template, mark the plywood motor mounting plate
where the four holes are to be drilled.
-Remove the aluminum motor mounting plate and
drill a 1/8”(3mm) hole through the plywood at each
of the four marks marked .
Note: The aluminum motor mounting included with
electric motor set.
3mm
- Remove the plywood motor mounting and drill a
6mm holes through the beam at each of the
four marks made above.
6x100mm..........4
6mm nut.........12
6mm washer...16
6mm
! Align the mark on plywood motor mounting
with the mark on the fire-wall.
! Align the mark on plywood motor mounting
with the mark on the fire-wall.
ZLIN Z-526 14- Electric motor
Table des matières
