Zennio ZDID64V3 Manuel utilisateur

DALI BOX Interface 64 v3

Interface for one DALI bus with up to 64 devices and 64 lighting groups

ZDID64V3 TECHNICAL DOCUMENTATION

FEATURES

•Possibility of controlling up to 64 DALI ballasts and up to 64 lighting

groups (groups from number 17 to number 64 are only for one DALI

ballast)

•Single Master DALI-2 Controller

•Compatibility with emergency lighting and color ballasts (DT8).

•Scene sending and saving

•Error detection and monitoring

•Burn-in, Stand-by and Auto-off functions

•Manual control through buttons and status indication through display

•1.54” display (128 x 64 pixels) for settings and notifications

•External power supply of 110-240 VAC 50/60 Hz

•Total data saving on KNX bus failure

•Integrated KNX BCU (TP1-256)

•Size 67 x 90 x 79 mm (4.5 DIN units)

•DIN rail mounting according to IEC 60715 TH35, with fixing clamp

•DALI Standard certified

•Conformity with the CE, UKCA, RCM directives (marks on the right

side)

1. DALI bus channel

2. Control buttons

3. Display

4. Programming button

5. Programming LED

6. Power supply indicator LED

7. External power supply

8. KNX connector

Figure 1: DALI BOX Interface 64 v3

Programming button: short press to set programming mode. If this button is held while plugging the device into the KNX bus, it enters the safe mode.

Programming LED: programming mode indicator (red). When the device enters the safe mode, it blinks (red) every half second. During the start-up

(reset or after KNX bus failure) and if the device is not in safe mode, it emits a red flash.

GENERAL SPECIFICATIONS

CONCEPT

DESCRIPTION

Type of device

Electric operation control device

KNX supply

Voltage (typical)

29 VDC SELV

Voltage range

21-31 VDC

Connection type

Typical TP1 bus connector for 0.8 mm Ø rigid cable

Maximum

consumption

Voltage

29 VDC (typical)

6,2

179.8

24 VDC¹

240

External power

supply

Voltage

110-240 VAC 50/60 Hz PF=0.5

Maximum consumption

82 mA @ 110 VAC / 52 mA @ 230 VAC

Operation temperature

-5 .. +45 °C

Storage temperature

-20 .. +55 °C

Operation humidity

5 .. 95%

Storage humidity

5 .. 95%

Complementary characteristics

Class B

Protection class / Overvoltage category

II / III (4200 V)

Operation type

Continuous operation

Device action type

Type 1

Electrical stress period

Long

Degree of protection

IP20, clean environment

Installation

Independentdevice to be mounted inside electrical panelswith DIN rail (IEC

60715)

Minimum clearances

Not required

Response on KNX bus failure

Data saving according to parameterization

Response on KNX bus restart

Data recovery according to parameterization

Operation indicator

The programming LED indicates programming mode (red). The power

supply LED indicates external power (green). Display allows both

configuring the DALI system and supervising the current status.

Weight

195 g

PCB CTI index

175 V

Housing material

PC FR V0 halogen free

¹ Maximum consumption in the worst-case scenario (KNX Fan-In model).

SAFETYINSTRUCTIONSAND ADDITIONAL NOTES

•Installation should only be performed by qualified professionals according to the laws and regulations applicable in each country.

•Do not connect the mains voltage nor any other external voltage to any point of the KNX bus; it would represent a risk for the entire

KNX system. The facility must have enough insulation between the mains (or auxiliary) voltage and the KNX bus or the wires of other

accessories, in case of being installed.

•The facility must be equipped with a device that ensures the omnipolar sectioning. Installation of a 10 A mini-circuit-breaker is

recommended. To prevent accidents, it must remain open in case of manipulation of the device.

•The device has a short-circuit protection fuse that, in case of activation, should only be rearmed or replaced by the Zennio technical

service.

•This device contains a security short-circuit proof transformer.

•Once the device is installed (in the panel or box), it must not be accessible from outside.

•For indoor use only.

•Keep the device away from water (condensation over the device included) and do not cover it with clothes, paper or any other material

while in use.

•The WEEE logo means that this device contains electronic parts and it must be properly disposed of by following the instructions at

https://www.zennio.com/en/legal/weee-regulation.

•This device contains software subject to specific licences. For details, please refer to https://zennio.com/licenses.

DALI OUTPUT SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Number of channels

Output type / Voltage

DALI bus / 18 VDC SELV

Guaranteed current per channel

200 mA

Maximum current per channel

250 mA

Maximum DALI ballasts per channel

Maximum length of cable

300 m (@ 1.5 mm²)

Short-circuit protection

YES

Overload protection

YES

Over-voltage protection

YES

Connection method

Screw terminal block (0.5 Nm max.)

Cable cross-section

1.5-4 mm² (IEC) / 26-10 AWG (UL)

EXTERNAL POWER SUPPLY SPECIFICATIONS AND CONNECTIONS

CONCEPT

DESCRIPTION

Power supply protection

fuse

Voltage

250 V

Current

4 A

Response type

F (Fast acting)

Connection method

Screw terminal block (0.5 Nm max.)

Cable cross-section

1.5-4 mm² (IEC) / 26-10 AWG (UL)

WIRING DIAGRAMS

Figure 2: Mounting DALI BOX Interface 64 v3

on DIN rail

110-240 VAC

50/60 Hz

Ballast n

(n≤64)

Ballast 1

⚠In case of ballast replacement,

please follow the steps defined in

the user manual.

⚠In case of a DALI channel short

circuit, the device will monitor the

DALI channel in order to switch on

the output at full current just as the

short circuit is removed.

Attaching DALI BOX Interface 64 v3 to DIN rail:

Removing DALI BOX Interface 64 v3 from DIN rail:

Autres manuels Zennio Équipement d'enregistrement

Zennio

Zennio KNX ZRX-KCI4S0 Mode d’emploi

Zennio

Zennio ZRX-KCI4SO Manuel utilisateur

Zennio

Zennio DALIBOX ZDI-DLB4 Mode d’emploi

Zennio

Zennio DALIBOX Interface 64/32 Manuel utilisateur

Zennio

Zennio KIPI Manuel utilisateur

Zennio

Zennio ZDI-DLI Manuel utilisateur

Zennio

Zennio KNX ZRX-KCI4S0 Mode d’emploi

Zennio

Zennio KLIC-DI Guide de démarrage rapide

Zennio

Zennio DALIBOX ZDI-DLB4 Mode d’emploi

Zennio

Zennio KLIC-DI SKY Manuel utilisateur

Zennio

Zennio KLIC-DD Manuel utilisateur

Zennio

Zennio DALIBOX ZDI-DLB6 Mode d’emploi

Zennio

Zennio KNX KCI 4 S0 Manuel utilisateur

Zennio

Zennio DALIBOX ZDI-DLB4 Mode d’emploi

Zennio

Zennio ZRX-KCI4SO Mode d’emploi

Zennio

Zennio KNX USB SC Manuel utilisateur

Zennio

Zennio BIN 44 Manuel utilisateur

Zennio

Zennio KLIC-DI Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien