ZENEC Z-E4626/H Guide de démarrage rapide

P a g e | 1

Z-E4626/H Installation Notes

Z-E4626/H Installation Notes V1.1

Below is a list of standard settings that we recommend be set on the Universal Zenec Z-E4626/H. Some of the below

settings are only the “recommended settings” based off our testing but they may not suit the personal preferences

of the End User so it is important to show them how to change these settings.

Antenna Remote Wire –The Blue P. ANT wire on a Zenec is a switch wire and is not designed to power antenna

boosters in vehicles or antennas that require a 12v supply. We recommend connecting these wires to an

accessory/ignition source.

Steering Controls & Speed_IN –Due to the variety of different Mercedes Benz Vehicles this head unit is compatible

with, either a CTSMC011.2 (W447 Vito) or a CX401-MB01 has been provided for CAN-Bus and Steering Wheel

Controls. Connect the steering control output wire from either interface to the grey wire labelled “IR In” which is on

the same connector as the Microphone and Camera input of the Zenec device. The Pink Speed_IN wire is not used.

Bluetooth Pairing –Please READ

The Z-E4626/H has dual phone pairing functionality which allows for two handsets to be connected and used at the

same time. However, for this feature to work correctly you will need to follow the below instructions.

•Initiate the pairing of the first (most used) device

•Wait until the phone book and call history are completely downloaded to the Zenec device. This may take

some time on the first connection and will depend on the number of contacts on the phone.

•While this process is taking place, avoid using the phone for SMS or phone calls.

•Once it has completed then you can initiate the pairing of the second phone as per the above instructions.

1) After the installation is completed and BEFORE you set up anything on the device please follow the below

instructions to perform a “Load Factory”.

Go To Setup in the Home Screen and Press Device

Setup (bottom right as highlighted) then Press Help

Press OK next to Load Factory and Press Yes to confirm.

The unit will reboot.

PLEASE READ BEFORE INSTALLATION

P a g e | 2

2) Access the Car Setup Menu as Highlighted to setup the reverse camera and vehicle settings.

In Car Setup you can program the Zenec for reverse

camera and other important settings

Park Assist –This is where you program the Zenec

for reverse camera

Reverse Audio Assist –Here you can program what will

happen to the audio when Reverse is engaged

Driver Position –Please make sure that this setting is

changed to Right Hand Drive

3) Access the Bluetooth Setup Menu as Highlighted in the below Screen Shot

1. Microphone –Choose External or Internal*

2. Display Order –Change this setting to First Name

so that the BT Contacts will be display by First

Name

3. Device Name –This allows the End User to change

the BT Broadcast name so they can easily identify

the BT device they are connected too.

*We strongly advise installing an external microphone

for optimum voice quality

4) Access the TFT Settings Menu

TFT Settings –This menu allows you to change the

device brightness settings and controlled how the

device is dimmed for low light or night mode.

TFT Control –We recommend changing this setting to

Car which will adjust the brightness when the cars lights

are turned on. Navi will adjust the brightness by the

current GPS Location.

Table des matières

Autres manuels ZENEC Système vidéo embarqué

ZENEC

ZENEC ZE-NC510 Manuel utilisateur

ZENEC

ZENEC Z-E2026 Manuel utilisateur

ZENEC

ZENEC Z-N326 Feuille d'instructions

ZENEC

ZENEC INFOTAINER Z-N328 Manuel utilisateur

ZENEC

ZENEC ZE-NC2040 Manuel utilisateur

ZENEC

ZENEC ZE-NC3810 Manuel utilisateur

ZENEC

ZENEC ZE-NC2011D Manuel utilisateur

ZENEC

ZENEC Z-N975 Manuel utilisateur

ZENEC

ZENEC ZE-NES14 Manuel utilisateur

ZENEC

ZENEC ZE-NC3810 Manuel utilisateur

ZENEC

ZENEC ZE-NC5011D Manuel utilisateur

ZENEC

ZENEC ZE-MR1020-DVD Manuel utilisateur

ZENEC

ZENEC Z-E2050 Manuel utilisateur

ZENEC

ZENEC ZE-NC4110 - MOUNTING INSTRUCTIONS FOR SANTA... Manuel utilisateur

ZENEC

ZENEC ZE-NC3811D Manuel utilisateur

ZENEC

ZENEC ZE-NC520 Instructions de montage

ZENEC

ZENEC E3776 Manuel

ZENEC

ZENEC E GO ZE-NC3152 Manuel utilisateur

ZENEC

ZENEC Z-E2050 Manuel utilisateur

ZENEC

ZENEC Z-E3726 Feuille d'instructions

ZENEC

ZENEC ZE-NC3131D Manuel utilisateur

ZENEC

ZENEC Z-E3766 Guide de l'utilisateur

ZENEC

ZENEC Z-N326 Manuel utilisateur

ZENEC

ZENEC ZE-NC5010 Manuel utilisateur

Manuels Système vidéo embarqué populaires d'autres marques

Stinger

Stinger HEIGH10 RB10RAM13B Manuel utilisateur

Eonon

Eonon E1057 Manuel utilisateur

Milion

Milion D2223 Manuel utilisateur

Metra Electronics

Metra Electronics 99-8153 Manuel utilisateur

Voxx Electronics

Voxx Electronics HR8MA1 Manuel utilisateur

Axxera

Axxera AV604Bi Manuel utilisateur

Clarion

Clarion NX706E Manuel utilisateur

Pyle view

Pyle view PLDN74BTi Manuel utilisateur

Clarion

Clarion NX602 Manuel utilisateur

PowerAcoustik

PowerAcoustik PTID-5850N Manuel utilisateur

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guide de l'utilisateur

Lanzar

Lanzar SVDVD5 Manuel utilisateur

Kia

Kia MTXM100YPPE Manuel utilisateur

Eonon

Eonon E1060 Manuel utilisateur

Macrom

Macrom M-AN900 Manuel utilisateur

Hyundai

Hyundai BAPE-L3000N Manuel utilisateur

r.LiNK

r.LiNK RL2-UCON8-SM Manuel utilisateur

Blaupunkt

Blaupunkt DVP 01C Manuel utilisateur