Zcom AS220V2 Manuel utilisateur

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Package Contents

One indoor

access point

One mounting bracket

+ one screw

Two mounting bracket screws

+ screw anchors

One

allen wrench

One quick start guide

Installation Requirements

Pair (STP) cabling. In addition, please cut the cable into a proper length, strip the cables on both

ends, and crimp the wires into RJ45 connectors. It is the professional installer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

Mounting the Access Point

In-wall mount

Determine where you want to mount the device, position the socket into the slot.



Insert the mounting bracket into the socket using

the two screws (included in the packaging).



Slide the device onto the mounting

bracket to finish the installation.

Note: Before lock two screws into the socket, please reserve space up to 15 cm in length

above bracket for installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Wall mount

Determine where you want to mount the device, position the mounting bracket onto the wall,

and use a marker to mark the two screw holes on the wall.

Note: Before drill two holes into the wall, please reserve space up to 15 cm in length

above bracket for installation.

Drill the two holes into the wall and insert the two screw anchors (included in the packaging)

into the holes.



Install the mounting bracket onto the wall

using the two screws (included in the

packaging) into the screw plugs in the wall.



Slide the device onto the mounting bracket

to finish the installation.

Ceiling Mount (Optional accessory_AS-CLM4)

Determine where you want to mount the device, position the mounting bracket onto the ceiling

board.

Use a marker to locate the two screw holes on the ceiling, and drill the two holes into the ceiling.

Note: The thickness of ceiling board should be less than 15mm.



Insert the ceiling screw through the mounting

bracket, ceiling board, and ceiling mount as the

following picture.



Slide the device onto the mounting bracket

to finish the installation.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Installing the Anti-tamper Lock (Optional accessory_AS-LK18)

Slide all the cables through their respective holes on the anti-tamper lock.

Install the mounting bracket; plug all the

cables into their respective ports on the

device before installing the anti-tamper lock.

Position the anti-tamper lock onto the

device and fasten the lock screw clock-wise

with special anti-tamper lock key.

Safety Notice

1. Do not install the device close to any electrical grounding device or lightning protection system.

Place the device’s own grounding and lightning protection system apart from any electrical

grounding device and lightning protection system as far as possible.

2. Protect components from electrostatic discharge: Please wear an ESD wrist strap or handle the

power adapter by its edge and do not touch any component or printed circuit boards,

especially for module device.

3. Make sure to keep the temperature and humidity of the installation location at an optimal

level.

4. An excellent grounding system guarantees the stable operation of device, as well as to protect

device from lightning, interference and electrostatic discharges.

5. If installed outdoors, the device may be damaged by lightning. We recommend that you install

additional lightning protection devices if necessary, considering the conditions in your area.

6. Supply stable power to the device. Unstable power may cause the device to malfunction. The

device supports PoE power supply and is recommended if the device is installed near grid lines

within less than 100 meters radius.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Powering the Access Point

By WAN/PoE

Connect the PoE cable into the WAN/PoE IN

port of the device.

By a power adapter

(Optional accessory_ AC-48052)

Connect the power adaptor into the DC port

of the device.

LED Indicator

Color

Behavior

Description

Red

Steady

Initializing

Flashing

Factory defaults, waiting to be integrated

Blue

Flashing

Device is busy updating its firmware; do not touch or unplug it

Green

Steady

Ethernet connection detected

Flashing

No Ethernet connection detected

In a default access point configuration, the access point default AP mode is TAP mode, and obtains

IP addresses from DHCP Option 43 protocol.

Note: In TAP mode, the AP must be able to go with Wireless LAN Controllers (WLCs) for

bulk configuration and performing other commands of access points. Please refer to WLC

QSG for settings first, then go back to finish the AP configuration.

https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=49

Step 1. Power on the access point. As the status of LED indicator from flashing change to steady

green, the connection is successful.

Note: Please make sure DHCP is enabled on the network once accomplished WLC

settings. The access point must receive its IP address through DHCP.

Note:

It's available to turn on the access point by either





Note: Please wait for 5-10 seconds while powering on.

Note: For PoE Out applications, the LAN port provides DC 48V, Max. 208mA, and up to

10W power supply. The positive side of the 48V is connected to pin 4 and 5, the negative

side is connected to pin 7 and 8.

Warning:Do NOT attempt to connect any non-PoE devices to LAN port and make sure

the input power should comply with PoE Out standard.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Note: Switching from DHCP to assign a static IP address or DNS and L2 discovery mode

to the access point, please refer to the user manual for more information.

https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25

If the access point cannot connect to the WLC by DHCP broadcast, please refer to the following

optional settings.

Optional: Set up a static IP address

Note: The following procedure assumes that Windows 10 is the operating system.

Procedures for other operating systems are similar.

Step 1. On your computer, configure your network adapter from the “Local Area Connection

“settings as follows:

˙StartControl PanelNetwork & InternetChange Adapter OptionsEthernet

Step 2. Edit the TCP/IPv4 address setting as follows:

˙PropertiesInternet Protocol Version 4 (TCP/IPv4)

Step 3. Select “Use the following IP address”and make the following entries:

˙IP address: 192.168.1.168 (or any available address in the 192.168.1.x network, except

192.168.1.1)

˙Subnet mask: 255.255.255.0

Leave the “Default gateway” and “DNS server” fields empty.

Step 4. Click “OK” to save your changes.

Step 5. Launch a Web browser; type default URL 192.168.1.1 to connect to the access point.

When a security alert dialog box appears, click OK/Yes to proceed.

Step 6. When login page appears, enter the following: Username: root/Password: password

Step 7. Click login.

Customizing the Wireless Settings

On the Web interface menu, Select StatusGeneral in the menu bar. Check your switchmod item

to select “Connect with via IP”, and setup your WLC IP address on “Wireless Switch Address 1”.

Note: IP address of WLC needs to be assigned (ex. 192.168.1.228) while on operation.

Note: If you need a standalone access point, please change to FAP mode.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

FAP Mode

The default AP mode is TAP mode, before FAP configurations please change AP mode.

Step 1. Currently in TAP Mode: On the Web interface menu, click SystemAP mode.

Step 2. Select Fat AP from the drop-down list.

Step 3. Click save & apply to take effect.

Note: For FAP mode, please refer to the user manual for more information.

https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=25

Mobile APP

Z-COM offers the App for bridge mode settings. Please research and download it to provision.

If necessary: reset button

If the access point needs to be reset, please press and

hold the reset button for more than ten seconds to

restore to factory default settings.

Technical Specifications

Physical

Dimensions

(L x W x H)

96 x 29.9 x 192 mm

(3.78 x 1.18 x 7.56 in) WAN/PoE In Port One 10/100/1000 Mbps port

Weight

500 grams (1.1 lbs.)

LAN/PoE Out Port

One 10/100/1000 Mbps port

Antenna 2.4GHz: Embedded 2dBi omni antennas

5GHz: Embedded 2.5dBi omni antennas

Power Supply

DC 48V, 0.5A PoE, or DC Jack (optional accessory)

LAN/PoE Out 48V/10 Watts (Max.), Passive PoE (Pairs 4, 5+; 7, 8 Return)

Power Consumption

Max. 12 Watts

Environmental

Temperature

Humidity

Operating

-10°C to 60°C (14°F to 140°F)

10% to 90% (Non-condensing)

Storage

-20°C to 70°C (-4°F to 158°F)

10% to 90% (Non-condensing)

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Compliance

RF Exposure Warning

The antennas used for this transmitter must be installed to provide a separation distance of at least

20 cm from all persons and must not be located or operating in conjunction with any other

antenna or transmitter.

CE Marking

CE marking on this product represents the product is in compliance with all directives that are

applicable to it.

Note: This device meets Max. TX power limit per ETSI regulations.

Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz

frequency range within all member states.

WEEE Compliance Statement

European Directive 2012/19/EU requires that the equipment bearing this symbol on the product

and/ or its packaging must not be disposed of with unsorted municipal waste. The symbol

indicates that this product should be disposed of separately from regular household waste streams.

It is your responsibility to dispose of this and other electric and electronic equipment via

designated collection facilities appointed by the government or local authorities. Correct disposal

and recycling will help prevent potential negative consequences to the environment and human

health. For more detailed information about the disposal of your old equipment, please contact

your local authorities, waste disposal service, or the shop where you purchased the product.

AS220V2 2x2 Dual Band 802.11ac Wave 2 Indoor Access Point QSG

Declaration of Conformity

Hereby, Z-COM, Inc. declares that the radio devices are in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

https://www.zcom.com.tw/index/downloads?keyword=&meterial_type=56

Optional Accessories

PN Item Picture

AS-CLM4 Ceiling mount + two screws

AS-LK18 Anti-tamper Lock

AC-48052 48 V 0.52A power adapter

Contact Information

All information may be changed by Z-COM at any time without prior notice or explanation to the

user. For further information please refer to our website: www.zcom.com.tw

Autres manuels pour AS220V2

Table des matières

Autres manuels Zcom Point d'accès sans fil

Zcom

Zcom AS220V2 Manuel utilisateur

Zcom

Zcom ZAC Series Manuel utilisateur

Zcom

Zcom ZAC-1023-2 Manuel utilisateur

Zcom

Zcom XG-3120 Manuel utilisateur

Zcom

Zcom ZAC-1023-5 Manuel utilisateur

Zcom

Zcom SP250 Manuel utilisateur

Zcom

Zcom AC-1025D Manuel utilisateur

Zcom

Zcom AS220V2 Manuel utilisateur

Zcom

Zcom XG-580 PLUS Manuel utilisateur

Zcom

Zcom ZN-7100-DE500-G V4 Manuel utilisateur

Zcom

Zcom AC-1031 Manuel utilisateur

Zcom

Zcom SP230 Series Manuel utilisateur

Zcom

Zcom SP220V2 Series Manuel utilisateur

Zcom

Zcom SP230 Series Manuel utilisateur

Zcom

Zcom AS420 Manuel utilisateur

Zcom

Zcom XG-1020 Manuel utilisateur

Zcom

Zcom XV-5850 Manuel utilisateur

Zcom

Zcom ZAC-1023-2-9 Manuel utilisateur

Zcom

Zcom SP230 Series Manuel utilisateur

Zcom

Zcom SP420 Series Manuel utilisateur

Zcom

Zcom AC-1028 Manuel utilisateur

Zcom

Zcom ZCN-1523H-2-8 Manuel utilisateur

Zcom

Zcom ZAC Series Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur