Z Microsystems SL Manuel utilisateur
Command
Console
SL
Doc# 27-0032UM Rev A Issued 07/05
2
Command
Console
SL
FCC INFORMATION
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED AS PLUG WITH AN EXTENSION
CORD RECEPTACLE OR OTHER OUTLETS UNLESS ALL THREE PRONGS CAN BE FULLY
INSERTED
CAUTION
RISK OF ELECTRIC SHOCK - DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK OF UNIT). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-
FIED PERSONNEL.
This symbol warns the user that insulated voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore, it is dangerous to make any kind of
contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and
maintenance of this unit has been included. Therefore it should be read carefully in
order to avoid any problems.
REGULATORY
1. Use the power and
video cables supplied
with the product to
help prevent interfer-
ence with radio and
television reception.
The use of cables
and adapters may
cause interference
with electronic equip-
ment in the vicinity of
this unit.
2. Changes or
modifications not
expressly approved by
Z Microsystems could
void user’s warranty.
Doc# 27-0032UM Rev A Issued 07/05
3
SECTION PAGE
Introduction ........................................................................................................................4
About This Manual ....................................................................................................4
Safety Precautions ....................................................................................................4
Product Description ..................................................................................................5
Installation Instructions .......................................................................................................6
Shipment Contents ...................................................................................................6
Required Tool ............................................................................................................6
Preparations ..............................................................................................................6
Hardware Installation ................................................................................................7
Install Rails ................................................................................................................8
Install Console ........................................................................................................10
ZLocks Description .................................................................................................12
Setup Console ........................................................................................................13
Close Console .........................................................................................................15
Cable Connections .................................................................................................16
Operations .......................................................................................................................16
Power Up ................................................................................................................16
Display Panel Controls ...........................................................................................17
Display Panel Setup ................................................................................................18
Onscreen Menus .....................................................................................................19
SoftMenus ...............................................................................................................23
Maintenance ...................................................................................................................28
Troubleshooting ..............................................................................................................29
No Main Display Image ...........................................................................................29
Display Image Has Vertical Bars ............................................................................30
Display Image Appears Fuzzy ................................................................................30
Power Light Does Not Illuminate ............................................................................30
Schematics .....................................................................................................................31
Replacements .................................................................................................................36
Appendix .........................................................................................................................37
Specifications for Command Console ...................................................................37
Warranties ..............................................................................................................39
Customer Support ...................................................................................................45
Customer Feedback ................................................................................................46
Command Console Serial Control ICD ..................................................................47
TABLE OF CONTENTS
Doc# 27-0032UM Rev A Issued 07/05
4
ABOUT MANUAL
Safety Precautions
DANGER:
To avoid shock hazard:
Do not remove the covers around the
Command Console
Do not connect or disconnect the
Command Console during an
electrical storm.
e power cord plug must be connected
to a properly wired and grounded
power outlet.
Any equipment to which the
Command Console will be attached
must also be connected to properly
wired and grounded power outlets.
•
•
•
•
This Manual is also available on the Z Microsystems website (www.zmicro.com). We
recommend you read this manual carefully and follow the instructions in the Installation
chapter for verification of system functions and control settings.
INTRODUCTION
Doc# 27-0032UM Rev A Issued 07/05
5
PRODUCT DESCRIPTION
INTRODUCTION
The ultra-slim Command Console SL model is designed for rapid deployable applications
and fits any 19” RETMA rack or transit case. The Command Console SL model brings
together a 19” (1280 x 1024) flat panel display, a full size water tight keyboard and track
ball all in only 1.75” (1U) height.
The Command Console SL model also solved cable retracting problems. An integral
custom engineered articulating arm provides smooth cable management which eliminates
cables from getting tangled and caught on other equipment as the Console is pulled in
and out of the rack.
To further assure rapid deployment, dual quick-lock/release mechanisms hold the Com-
mand Console SL model firmly in the storage position and allow it to be quickly set up
and operational. A custom torque adjustable hinge can be adjusted to hold the display
securely at any viewing angle, in the most turbulent situations.
The Command Console SL model is manufactured entirely from lightweight, aircraft
grade, CNC machined aluminum and finished with a tough, baked powder coating to
provide the utmost strength, durability and light weight.
All configurations have the following “key features”:
• USB Connections or PS/2 Connections (connector clamp-down) for keyboard and TB.
• 88-key water tight keyboard.
• Three button sealed trackball
• 12-function keys and arrow keys.
• Fits 24in and 25in deep racks.
Doc# 27-0032UM Rev A Issued 07/05
6
Required Tools
• Phillips screwdriver, 2 pt.
• 5/16 wrench
NOTE: For the fastest and easiest
installation of the Command
Console, follow these steps
in the sequence they are
presented.
Preparations
In preparation to install the Command
Console, take the following precautionary
steps:
Verify the Command Console power
switch is OFF.
Do not connect or disconnect the unit dur-
ing an electrical storm.
The power cord plug must be connected to
a properly grounded power outlet.
Any equipment to which the unit will be at-
tached must also be connected to properly
wired and grounded power outlets.
Ensure all of the following parts are in-
cluded in the package received from Z Mi-
crosystems. Verify all parts have not been
damaged during shipment. If any of the
parts are missing or damaged, immediately
contact Z Microsystems Customer Service
at 858-657-1000.
• Command Console unit
attached to the mounting
plate
• Power Cable
• User Manual
• Video Cable
• Serial Cable
• Rack-mounting hardware
Remember to save the unit’s original
shipping materials. It may be necessary to
move the unit at a later date.
SHIPMENT CONTENTS
INSTALLATION
Doc# 27-0032UM Rev A Issued 07/05
7
HARDWARE INSTALLATION
INSTALLATION
Remove the outer rack mounting slide
channels from the Console.
On the rear unscrew the left and right
rear rack mounting brackets to free up
the outer rack mounting slide channels
from the Console.
Press the spring loaded Z Locks towards
the middle to release the outer rack
mount slide channels and at the same
time slide the rack mounting block back.
Slide the channels back until they stop
about half way back. This is a safety stop
to prevent the Console from sliding out
too far while mounted to the rack.
Simultaneously press in the first set of
safety catches on each slide rail and
slide the channel until the second safety
catches stop the sliding action.
Simultaneously press in the second set
of safety catches on each slide rail and
slide the channel all the way off the back
of the Console.
Doc# 27-0032UM Rev A Issued 07/05
8
INSTALLATION
Both outer rack mount slide channels
should be separated at this time.
The slide channels come pre-assembled
to fit a 24” deep rack. To fit a 25” rack, the
Install Rails
rear mounting bracket can be repositioned
as shown here.
Doc# 27-0032UM Rev A Issued 07/05
9
INSTALLATION
To mount the channels on the front of the
RETMA rails (in most cases), use two 10-
32 Phillips screws...
on each side to secure the Z-Lock mounts.
Be sure to press the slide rail flat against
the RETMA rail as you tighten the screws.
On the rear of the cabinet frame, also use
two Phillips screws on each rail to secure.
On the slide rails, using a screwdriver and
wrench, tighten the slide extension rail
screw. Repeat on each side.
Doc# 27-0032UM Rev A Issued 07/05
10
Pull the two Console inner members of the
slides out until they lock in the second lock
position.
Guide the Console’s inner slide member
into the middle slide member, and gently
slide the Console into the slide assembly
until it stops. This may require a second
person to support the power supply.
Press in the first set of catches on each
slide and slide the channel until the second
safety catches stop the sliding action.
Simultaneously press in the second set of
safety catches on each slide rail and slide
the channel all the way off the back of the
Console.
Install Console
INSTALLATION
Hold the Console with the front toward you
and as horizontal as possible. NOTE: In
the next step, be sure to carefully support
and guide the power supply at the rear of
the Console.
From the back of the rack, gently guide the
power supply toward you.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Z Microsystems Mixeur musical
