YT TUES Manuel utilisateur
rtfm.
read first - Then unpack
ZUERST LESEN - DANN AUSPACKEN
D’ABORD LIRE - ENSUITE DEBALLER
BIKE MANUAL
YT-INDUSTRIES.COM
Welcome to good times.
A
B
C
1
2
3
4
5
7
C
B
A
1
2
3
4
5
6
7
8
8
Oberrohr / Toptube / Tube Supérieur
Unterrohr / Downtube / Tube Oblique
Sitzrohr / Seattube / Tube de selle
Kettenstrebe / Chainstay / Base
Sitzstrebe / Seatstay / Hauban
Steuerrohr / Headtube / Tube de direction
Stoßdämpfer / Rear-shock / Amortisseur
Ausfallende / Drop out / Pattes
FEDERGABEL /
SUSPENSION FORK /
FOURCHE
Vorbau / Stem / Potence
Bremshebel / Brake Lever / Levier de frein
Lenker / Handlebar / Cintre
Schalthebel / Shifter / Commande de Vitesses
Steuersatz / Headset / Jeu de direction
Bremse vorne / Front brake / Frein avant
Bremsscheibe / Disc / Disque
LAUFRAD /
WHEEL / ROUE
Schnellspanner-Steckachse /
Quickrelease / Blocage de Roue
Nabe / Hub / Moyeu
Speiche / Spoke / Rayon
Felge / Rim / Jante
Reifen / Tire / Pneu
Ventil / Valve / Valve
Bremse hinten / Rear brake / Frein arrière
Bremsscheibe / Disc / Disque
Zahnkranz / Cassette / Cassette
Kettenführung / Chain Guide / Guide-Chaîne
Kettenblatt / Chainring / Plateau
Schaltwerk / Rear Derailleur / Dérailleur arrière
Kette / Chain / Chaîne
Tretkurbel / Crankset / Pédalier
Pedal / Pedal / Pédale
Sattelstütze / Seatpost / Tige de selle
Sattelstützenklemme / Seatpost Clamp /
Collier de serrage de tige de selle
Gabelkrone / Crown / Té
Standrohr / Stanchions / Plongeur
Tauchrohr / Casting / Fourreaux
Sattel / Saddle / Selle
6
RAHMEN / FRAME / CADRE
MONTAGE WERKZEUG ASSEMBLY TOOLS OUTILS DE MONTAGE
Inbusaufsatz Größe 4, 5 und 6mm
Inbusschlüssel Größe 4, 5 und 6mm
Drehmomentschlüssel mit 17er Nussaufsatz
Seitenschneider
Dämpferpumpe (Modelle mit Luftfeder)
Reifenpumpe
Montagefett
Carbon-Montagepaste
Torque wrench with Allen key adapter size 4, 5 and 6
Allen key size 4, 5 and 6
Torque wrench with socket key 17 mm
Wire cutter
Shock pump (models with air suspension)
Tire pump
Assembly grease
Carbon Paste
Clé dynamométrique avec insert Clé Allen, taille 4, 5 et 6
Clé Allen, taille 4, 5 et 6
Clé dynamométrique avec douille 17 mm
Pince coupante
Pompe amortisseur (modèles avec amortisseur à air)
Pompe de gonfl age des pneus
Graisse de montage
Graisse spéciale carbone
FEDERGABEL /
SUSPENSION FORK /
FOURCHE
INTRODUCTION
Congratulations on your new bike and
thanks for choosing YT INDUSTRIES.
PLEASE NOTE:
A mountain bike is a piece of technical sports equipment that in order to
function properly and sustainably satisfy the user demands a certain level of
technical know-how as well as assembly and maintenance skills.
Furthermore we assume that the users of our bikes possess suitable tools in
order to execute the necessary assembly steps without damaging the parts.
These assembly instructions cannot replace professional instruction or training
as bike mechanic.This manual is not intended to provide the knowledge
nor the skills required for professionally assembling a piece of
high tech sports equipment, like a mountain bike,
from single parts or for repairing such equipment.
Please understand that in case of self-executed repairs and/or
on-professional maintenance warranty on components shall be void
and we shall not accept liability for consequential accidents or damages.
TIP:
Please save the YTIndustries BikeBox including the
packaging material.This way, you can repack your
bike if you need to have it transported.
ATTENTION:
If you don’t feel confi dent in your abilities to perform the necessary
maintenance and repairs appropriately, seek out a bike shop!
Of course, you can always contact us if you have any queries.
But exclusion from warranty and limitations of our liability apply in
this case, too. When dealing with inquires by phone or mail,
we cannot ensure that the extent and the nature of the problems and
the applicable remedies have been described correctly and completely
and therefore we cannot control whether our work instructions have
been implemented correctly and to the full extent.
ASSEMBLY INSTRUCTIONS
eng
ASSEMBLY INSTRUCTIONS
UNPACKING THE FRAMEUNPACKING THE WHEELSOPENING THE BOX STEP
STEP
03
STEP
STEP
02
STEP
STEP
01
a
a
Cut the straps using wire cutters or a box cutter.
Just make sure that you do not damage the BikeBox.
b
b
Now you can pull out the fl aps and open the BikeBox.
a
a
Lift the wheels upwards out of the box.
b
b
b
Place the wheels in a safe place on their side.
a
a
Now you can pull your bike upwards out of the BikeBox.
b
b
b
Place the frame on the front/rear axle stand.
Make sure the bike is standing properly!
a a a
b b b
STEP
STEP
04 A INSTALLING THE HANDLEBAR - RACE FACE ATLAS DIRECT MOUNT
a
a
Remove the screws of the stem from the upper fork crown (5 mm Allen wrench).
b
b
b
Place the handlebar and stem on the fork crown.
c
c
c
Install the stem on the fork crown (5 mm Allen wrench).
d
d
Tighten the screws gradually with only one turn per screw in an X pattern.
This is the only way to achieve even clamping of the handlebar in the stem.
e
e
Adhere to the guidelines of the manufacturer of the stem and/or handlebar when
torqueing the screws. Make sure that the clamp gap is even and that the handlebar is
centered and inserted correctly. The adjustment lines will help you with this.
Adjust the handlebar to your preferred position by using a 5 mm Allen wrench.
a c e
b d
eng
During assembly, please adhere to the torque specifi cations of the manufacturers:
RaceFace Atlas Direct Mount
RaceFace Atlas Direct Mount
9Nm
Renthal Integra II: Fork crown screws (large)
Renthal Integra II: Fork crown screws (large)
10Nm;
Handlebar clamp screws (small)
Handlebar clamp screws (small)
6Nm
YT Industries Direct Mount
YT Industries Direct Mount
5Nm
(Last updated 2015)
CAUTION!
!
STEP
STEP
04 B INSTALLING THE HANDLEBAR - RENTHAL INTEGRA II
a c e
fb d
During assembly, please adhere to the torque specifi cations of the manufacturers:
RaceFace Atlas Direct Mount
RaceFace Atlas Direct Mount
9Nm
Renthal Integra II: Fork crown screws (large)
Renthal Integra II: Fork crown screws (large)
10Nm;
Handlebar clamp screws (small)
Handlebar clamp screws (small)
6Nm
YT Industries Direct Mount
YT Industries Direct Mount
5Nm
(Last updated 2015)
CAUTION!
!
a
a
Remove the screws of the stem from the upper fork bridge (5 mm Allen wrench).
b
Remove the screws of the stem from the upper fork bridge (5 mm Allen wrench).
Remove the screws of the stem from the upper fork bridge (5 mm Allen wrench).
b
b
Install the 2 lower bolts of the stem, but do not tighten them at this point.
Remove the bolts holding the top clamps in place.
c
Remove the bolts holding the top clamps in place.
c
Slide the clamps sideways over the handlebar into the mounting position.
Attach the handlebar and the top clamps to the base of the stem
(on the top crown of the fork).
d
d
Start to tighten the four crown screws fi rst.
Make sure there is no gap between the baseplate and the clamp.
e
Make sure there is no gap between the baseplate and the clamp.
e
Tighten the two front screws and make sure the handlebar is centered
and inserted correctly.The adjustment lines will help you with this.
f
and inserted correctly.The adjustment lines will help you with this.
f
Respect the torque recommendations of the manufacturer of the handlebar and stem.
ASSEMBLY INSTRUCTIONS
STEP
STEP
04 C INSTALLING THE HANDLEBAR - YT INDUSTRIES DIRECT MOUNT
a c e
fb d
a
a
Remove the screws of the stem from the upper fork crown (6 mm Allen wrench).
Install the stem on the fork bridge (6 mm Allen wrench).
b
b
Tighten the screws gradually with only one turn per screw in an X pattern.
This is the only way to achieve even clamping of the handlebar in the stem.
c
c
Remove the screws from the clamp of the stem.
d
d
Install the handlebar in the stem.
e
e
e
Tighten the screws gradually with only one turn per screw in an X pattern.
This is the only way to achieve even clamping of the handlebar in the stem.
f
f
Adhere to the guidelines of the manufacturer of the stem and/or handlebar when
torqueing the screws. Make sure that the clamp gap is even and that the handlebar is
centered and inserted correctly. The adjustment lines will help you with this.
During assembly, please adhere to the torque specifi cations of the manufacturers:
RaceFace Atlas Direct Mount
RaceFace Atlas Direct Mount
9Nm
Renthal Integra II: Fork crown screws (large)
Renthal Integra II: Fork crown screws (large)
10Nm;
Handlebar clamp screws (small)
Handlebar clamp screws (small)
6Nm
YT Industries Direct Mount
YT Industries Direct Mount
5Nm
(Last updated 2015)
CAUTION!
!
eng
REMOVE WHEELS
FROM PACKAGING INSTALLING THE REAR DERAILLEUR
a
a
b
b
Cut the cable ties using wire cutters and
remove the cardboard packaging.
a a c
b b
a
a
Open the rear derailleur cage by holding the derailleur body with one hand,
and turning the cage forward with your other hand.
b
b
The rear derailleur cage is locked by pressing and holding the small button
with the lock symbol.The rear derailleur will then stay open.
c
c
Mount the derailleur using the Torx T25 (7-speed) or
5 mm Allen wrench (10-speed) on the derailleur hanger.
Please make sure the bolt is perpendicular to the hanger to avoid
damaging the thread.
ASSEMBLY INSTRUCTIONS
STEP
STEP
06
STEP
STEP
05
During assembly, please adhere to the torque specifi cations of the manufacturers: 8 - 10 Nm
CAUTION:
!
Table des matières
Autres manuels YT Vélo
