YPHOS 01 Manuel utilisateur
01
INSTALLATION UIDE
3
Congratulations on your new lights!
Evenings at the boat are going to be so much better.
This guide will assist you to install your new YPHOS lights. The following instructions refer
to GRP (fiberglass) and wooden hulls – for other types of hulls please contact us for correct
guidance. Always make sure that you are familiar with the operations to be done and consult a
specialist to install the lights.
Always follow safety procedures and pay attention to all steps to ensure the longevity of your
new lights. Always wear protective gear and take safety first.
Intended Use
Model 01 is designed to operate as an LED Illumination unit for mounting on GRP or wooden
boat hulls. It can be installed above water level, partially or completely submerged in both
fresh and sea water and can be used anytime – while the boat is still or underway. This
installation manual does not supersede any National or Local Electrical Code.
4
In the Box
Make sure that all the elements shown below are in the box. If you are missing elements or
parts show signs of wear or damage, do not start the installation.
Model 01 LED Fixture
with 2m (6ft) cable
Fuse
2 Amp
2 x Tapping Screws
DIN7981 C PHIL 4.2x32 A4
5
You will also need:
Clean Cloths Sealant
3M™ Marine Adhesive Sealant
Fast Cure 4200FC
or similar
Drill Bit
Ø14mm (9/16”)
Drill Bit
Ø3mm (1/8”)
Crosshead
Screwdriver
Power Drill
6
Important Warnings
• Installation must be performed by a qualified installer.
• Installation must be done outside of water.
• Choose a flat area, easily accessible from the inside to mount the fixture.
• Install this fixture only on transom or sides of the hull.
• Do not use power tools to secure the fixture.
• Do not use solvents to clean the fixture.
• Do not modify whole or any part of this product.
• Wear personal protection gear during installation.
• Complete an electrical mock-up before you modify the boat.
• This is a 12V DC light fixture. Do not connect to mains or higher voltage than 15V DC.
• Do not look directly at the LEDs when in operation.
• Isolate power source prior to electrical installation.
• Each light should be individually fused.
• Do not allow exposed cable ends to come in contact with water. Capillary action will allow the ingress of water
through the cable, damaging the fixture or corroding the cable. This is not covered under warranty.
7
Switch off power
Inspect & Test the Light
Apply voltage to the light and confirm that it works as
intended before installation. Complete a connection
mock-up with all the necessary equipment before you
make any modification to the hull.
This protects you and avoids damaging your equipment.
Isolate the battery or power supply to make sure that
your system is off.
8
150 - 250mm
6” - 10”
Find the right spot
Select a flat surface to install the light fixture and make
sure that you have full access to the inner side of the
hull.
Make sure that no obstacles are restricting in any way
the mounting screws or the cable.
Recommended installation depth is 150-250mm
(6” - 10”) below the water line.
9
Prepare the Area
Drill
Use the provided template to mark the drilling locations.
Thoroughly clean the surface and remove any debris,
coatings, fluids or solid particles to ensure proper
adhesion.
Use a Ø3mm (1/8”) drill bit for the screw pilot holes and
a Ø14mm (9/16”) drill bit for the cable hole.
Clean again the surface before you continue.
10
Dry Fit
After the surface is completely clean and dry on both
sides, gently guide the cable through the cable bore
and dry fit the fixture onto the hull.
Make sure that the light fixture fits properly, the holes
are aligned and that the fixture sits flat on the hull
before proceeding to the next steps.
Table des matières
Autres manuels YPHOS Équipement d'éclairage
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
