Yoshimura RS-12 Manuel utilisateur

RESEARCH&DEVELOPMENT OF AMERICA, INC.

www.yoshimura-rd.com

5420 DANIELS STREET STE A, CHINO CA., 91710 · (800) 634-9166 · (909) 628-4722 · FAX (909) 591-2198

NOTE: IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM, WHICH INCLUDES THE CARBURETORS OF ANY VEHICLE.

You must know how to remove and replace your stock exhaust in order to install this product

otherwise have it installed by a professional mechanic. Keep all stock parts from your existing

system as some components may be necessary to install your new Yoshimura exhaust depending

on the application. Read through all instructions before beginning installation. Exhaust system can

be extremely hot. Let motorcycle cool down before beginning installation. Always wear hand and

eye protection and take precautionary measures to avoid injury.

RS-12 Taper Slip-On

228452S320 (SS/SS)

Honda CRF250R

Qualified Manufacturer Declared “Replacement Part”

2022 ~ 2023

Signature Series systems are:

• CARB/EPA tail-pipe emissions compliant.

• Marked with appropriate EPA noise labels.

• Independent laboratory tested for EPA new

vehicle noise compliance.

Z1024

Rubber Grommet

ALS-043

Aluminum Spacer

347PLUG

Muffler Wash Plug

M8X30H

8mm x 30mm

Flanged Hex Head Bolt

HT FOIL-9

Heat Foil Tape

228452S320-RMA

SS Muffler Assembly

Assembly Diagram

03019135

Exhaust Clamp

1. Remove the right side panel.

2. Loosen and remove muffler exhaust clamp.

3. Remove muffler tailpipe chassis mount bolt.

4. While securely supporting the stock muffler

assembly, remove muffler mount bolt and

carefully remove the stock muffler assembly.

5. Remove muffler gasket and muffler joint plate

off of stock header.

Removal

3. Torque muffler mount bolt and chassis mount

bolt to factory specifications.

4. Torque tailpipe exhaust clamp to 9.5 Nm (0.95

kg-m, 7 ft -lb).

5. Cut included HT FOIL-9, heat tape in half and

apply onto the backside of the right side panel

as shown below.

Note: Clean the backside of the side panel

where the heat tape is to be applied.

Make sure the surface is free of debris

and dry prior to application.

6. Re-install right side panel following the

opposite steps of removal.

7. Before starting motorcycle, check for proper

clearance between new exhaust system and

rear suspension (i.e. tire, swingarm, brakes,

rear shock, and etc.) If any problem is found,

please carefully follow through the installation

steps again. If problem still persists, please call

Yoshimura Tech Department at (800) 634-9166

/ in CA (909) 628-4722.

8. It is recommended that the muffler and tailpipe

be wiped down with rubbing alcohol to remove

oil and fingerprints. This will help prevent

tarnishing of the finish after the exhaust is

heated up.

Note: After starting motorcycle, it is normal for

new exhaust system and muffler to emit

smoke until oil residue burns off.

CAUTION: Exhaust system can be extremely hot.

Let motorcycle cool down before

beginning installation. Always wear

hand and eye protection and take

precautionary measures to avoid

injury.

WARNING: Always properly support vehicle with

a stand and/or lift when servicing or

performing any work. Unstable

vehicles may present dangerous

conditions and may cause property

damage and/or personal injury.

NOTE: Read through all instructions before

beginning installation.

Installation

1. Install Z1024, rubber grommet into muffler

bracket and install ALS-043, spacers as shown.

2. Slide exhaust clamp over muffler tailpipe inlet

and install muffler assembly onto header outlet.

Align chassis mount and secure using stock

chassis mount bolt. Align muffler mount and

secure using supplied M8X30H, 8mm bolt.

Dear Yoshimura Customer,

Congratulations and thank you for purchasing a Yoshimura Exhaust System. Over six decades of experience in research

and development, state of the art machinery, materials and craftsmanship of the highest quality all come together in a

product of exceptional quality and performance—in other words, this is the best thing you can put on your bike.

We strive to provide you with a product perfect in fit and finish. However, if you have any problems, please give us a

call. We have found that most fitment issues can be easily resolved by a conversation with one of our knowledgeable

and friendly staff. If the issue cannot be resolved this way, our warranty evaluation program may be the answer. Please

take a moment to review our recommendations for the care of your exhaust and our warranty information.

PLEASE NOTE: If you have any doubts about your exhaust: DO NOT START THE MOTORCYCLE! ONCE AN EXHAUST HAS

BEEN USED OR MODIFIED, IT CANNOT BE RETURNED FOR CREDIT OR EXCHANGE.

EXHAUST SYSTEM MAINTENANCE

Yoshimura Exhaust Systems require very little care and maintenance; here are a few tips:

1. Use mild car/motorcycle soap to clean the exhaust system—do not use any abrasives or degreasers.

2. Clean your exhaust with metal/stainless polish every 1-2 months to retain the luster and remove dirt and grime.

(DO NOT USE POLISH ON “WORKS FINISH” SYSTEMS)

3. Avoid contaminating exhaust surfaces when hot.

4. 4.Your exhaust system will change color (blue, magenta, purple, and/or gold) due to heat; this is normal.

5. Keep all clamps, bolts and other fasteners tight as exhaust systems are susceptible to vibration damage.

6. If you ride in coastal regions or areas that use salt to control ice and snow, wipe the exhaust down after it cools to

remove any possible salt residue, which can result in rusting.

7. If you are storing your motorcycle for the season, wipe the exhaust system down with rubbing alcohol before

storage.

8. Head pipes glowing (visible in normal light) may indicate an excessively lean condition that must be corrected.

CARBON FIBER:

Carbon fiber equipped exhaust components require special attention. The following addresses wear issues directly

related to carbon fiber:

1. Keep all clamps, bolts and other fasteners tight. Carbon Fiber is very susceptible to vibration damage.

2. Keep all chemicals and solvents away from the carbon fiber, as they will damage the finish.

3. High temperatures will cause the resin in the carbon fiber to break down. Visual signs such as an amber hue in the

resin may be early signs of heat damage to carbon fiber.

4. Upon seeing amber colored resin, discontinue use. The exhaust system needs to be inspected by a representative

from Yoshimura, for repack, and/or repair. Continued use will cause component failure.

STAINLESS STEEL:

Stainless Steel is not rust proof but is less prone to rusting, staining and pitting; but it is prone to oxidation like all

metals.

WORKS FINISH:

1. Works Finish exhaust systems should never be cleaned with abrasives or polishes.

2. Yoshimura recommends using “Bar Keepers Friend” cleaner to remove minor stains.

3. Surface reconditioning services are available to remove scratches and undesirable discoloration due to extreme

heat. Contact Yoshimura Tech Department at (800) 634-9166 / in CA (909) 628-4722 for more information.

RE-PACKING TIPS

To maintain maximum sound and engine performance the muffler packing will need to be replaced at some time during

the muffler’s life. Yoshimura recommends repacking your muffler at least once a year.

Failure to maintain the muffler packing may cause damage to the muffler and/or void the warranty. Regularly inspect

the muffler body for discoloration, cracks, rattling, or other signs of wear caused by depleted muffler packing. If muffler

packing is determined to be depleted or worn, a Yoshimura muffler re-pack kit is highly recommended to restore the

muffler to optimum maximum performance.

Yoshimura offers a 3-5 day turn around (plus transit time) to inspect and refurbish used and damaged mufflers.

For more information on muffler repacking please visit our website at: https://www.yoshimura-rd.com/pages/repack-

and-insert-chart

***PRO TIP*** Before you install your new muffler for the first-time log the weight in your Owner’s or Service manual

along with the current hours or mileage on your vehicle. When you are performing periodic maintenance on your

vehicle (like a tire change, or an oil change) you can remove your Yoshimura muffler from the vehicle and weigh it again.

Over time, the packing material inside your muffler will burn off with use, and the muffler will need to be repacked.

When the weight loses approximately 100 grams of the original weight, you should consider getting your Yoshimura

muffler repacked. You can order repacking kit or the parts to repack the muffler from the Yoshimura website, or

your local dealer. You can also contact the Yoshimura sales office and arrange to send in your muffler for the repacking

service too.

IMPORTANT TECHNICAL NOTE

Yoshimura recommends on all race exhaust systems, that all spring joints be safety wired. Recommended wire type

304/316 stainless steel with a .032” diameter should be used.

YOSHIMURA EXHAUST LIMITED WARRANTY

All Yoshimura R&D of America, Inc., exhaust systems carry a one-year limited warranty against defects in workmanship

and/or materials.

WHO IS COVERED?

This warranty is provided to the original purchaser of the exhaust system.

WHAT VOIDS THE WARRANTY?

1. Abuse, misuse, improper installation and/or modifications

2. Custom applications

3. No proof of purchase at the time of warranty. Claimant must provide proof of purchase (original receipt or invoice)

and a warranty authorization number (RMA) obtained from Yoshimura.

4. Finishes such as plating or painted surfaces with discoloration or rust due to inclement weather conditions, exposure

to salt, exposure to chemicals, or lack of maintenance by the customer are not covered.

5. International grey-market product purchased through a dealer/distributor not authorized for your country will not

be supported by this warranty.

EXTENT OF WARRANTY:

Any defective exhaust system properly returned to Yoshimura will be repaired or replaced by Yoshimura. Yoshimura is

not responsible for any other expense incurred by the customer under the terms of this limited warranty, nor is

Yoshimura responsible for any damages either consequential, incidental, special, contingent or otherwise; or expenses

or injury arising directly or indirectly from the use of the exhaust system. Any exhaust system returned to Yoshimura

must be sent at the customers expense along with the proof of purchase and warranty authorization (RMA). Yoshimura

reserves the right to determine whether the terms of the warranty, set out above, have been properly followed. In the

event that the terms are not followed this warranty is void. Yoshimura is the sole determiner of abuse, misuse,

installation errors and modifications—should any of these be found, this warranty is void. The duration of any and all

implied warranties are limited to the duration of the express warranty. All incidental or consequential damages are

hereby excluded. The warranty gives you specific legal rights and you may have other rights, which vary from state to

state. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how

long an implied warranty lasts, so the above limitations and exclusions may not apply to you.

If you have a fitment or other problem, or are missing a part, please double-check this trouble shooting guide first:

1. Reference your instruction sheet and double-check all drawings and instructions

2. Make sure muffler clamps are installed correctly (refer to instructions diagram). On many models, there is a right

and wrong way to install. Also verify part numbers on headers and tail pipe.

3. Always make sure to install spring-mounted manifolds and flanges on cylinder head prior to installing headers.

4. Always take time to examine problems in detail.

5. When all else fails, call our technical support line at (909) 628-4722. The technical line is open 9:00am – 4:30pm

Monday through Friday, Pacific Time. Please have the following information handy: Year/Make/Model of

motorcycle, date of purchase, place of purchase, batch dates and part numbers (found on header and tail-pipe

components).

6. Also, feel free to ask through online e-mail at sales@yoshimura-rd.com, or fax your question/problems to (909) 591-

2198.

To obtain technical information directly from Yoshimura, call (909) 628-4722.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Yoshimura Accessoires pour motos

Yoshimura

Yoshimura 15002B0520 Manuel utilisateur

Yoshimura

Yoshimura 225851S721 Manuel utilisateur

Yoshimura

Yoshimura Enduro Series Manuel utilisateur

Yoshimura

Yoshimura Street Series Manuel utilisateur

Yoshimura

Yoshimura 225850S321 Manuel utilisateur

Yoshimura

Yoshimura RACE Series Manuel utilisateur

Yoshimura

Yoshimura RACE 13100CP520 Manuel utilisateur

Yoshimura

Yoshimura RACE 131415M220 Manuel utilisateur

Yoshimura

Yoshimura 070BG123502 Manuel utilisateur

Yoshimura

Yoshimura 231032D320 Manuel utilisateur

Yoshimura

Yoshimura X-TREAD 559-592-V000 Manuel utilisateur

Yoshimura

Yoshimura RACE 11621C0520 Manuel utilisateur

Yoshimura

Yoshimura 070BG149500 Manuel utilisateur

Yoshimura

Yoshimura 070BG131001 Manuel utilisateur

Yoshimura

Yoshimura 070BG141503 Manuel utilisateur

Yoshimura

Yoshimura 19701BD520 Manuel utilisateur

Yoshimura

Yoshimura 070BG141200 Manuel utilisateur

Yoshimura

Yoshimura RACE131414M220 Manuel utilisateur

Yoshimura

Yoshimura Street 216600C250 Manuel utilisateur

Yoshimura

Yoshimura 19140NS720 Manuel utilisateur

Yoshimura

Yoshimura 070BG133001 Manuel utilisateur

Yoshimura

Yoshimura 570-400-0300 Manuel utilisateur

Yoshimura

Yoshimura ZX649SO Manuel utilisateur

Yoshimura

Yoshimura 224500D320 Manuel utilisateur

Manuels Accessoires pour motos populaires d'autres marques

SRC

SRC B-TRK502-01-01-SL Manuel utilisateur

3M Speedglas 9100 MP Manuel utilisateur

hepco & becker

hepco & becker 6307520 00 01 Manuel utilisateur

HOMCOM

HOMCOM AA0-077 Manuel utilisateur

hepco & becker

hepco & becker 6307558 00 01 Manuel utilisateur

Wunderkind Custom

Wunderkind Custom 106503-F15 Guide de l'utilisateur

Dräger

Dräger HPS 3500 Manuel utilisateur

M-WAVE

M-WAVE SKI Manuel utilisateur

Kuryakyn

Kuryakyn 6212 Manuel utilisateur

hepco & becker

hepco & becker 6507504 00 01 Manuel utilisateur

Tool it

Tool it PROMAX LCD 9.13G Manuel utilisateur

Custom Dynamics

Custom Dynamics TruWrapz Manuel utilisateur

Roof

Roof RO200 CARBON Manuel utilisateur

Kabuto

Kabuto Japan IBUKI Manuel utilisateur

PUIG

PUIG 5051 Manuel utilisateur

rizoma

rizoma ZTH050 Manuel utilisateur

Joubert

Joubert 10001711 Manuel utilisateur

Sperian

Sperian Optrel p420 Manuel utilisateur