Yard Craft Pluto Manuel utilisateur
Pluto Assembly Manual
Parts List
• #2 Square Drive Bit
• 4mm Hex Drive Bit
• Hammer or Rubber Mallet
• Wrench & Socket Set
• Drill and Drill Bits
• Impact Driver
• Tape Measure
• Step Ladder
•Level
Tools Required Tools Included
Use your imagination to explore the outer regions of space on YardCraft’s Pluto Vinyl
Playset!
Like its namesake, this set is our most compact vinyl play-sets so your kids can have fun
without taking up all the real estate!
The vinyl construction keeps this playset low in mainte-nance but keeps the fun factor high!
The Pluto Vinyl Playset will enhance the appearance of your backyard, while also making it a
one-stop-shop for having fun and making memories!
Patiova © 2022 v1.2
Type Quantity 91" 2x6 Swing Beam 1
42" 4x4 Post 44x4 End Post 1
67" 2x6 293" 2x4 Ground Runner 1
80" 2x6 Railing 287" 2x4 Braces 2
32" 2x6 4Beam Strap Bracket 1
44" 2x4 Joists 2Corner Bracket 1
84" 2x6 Legs 2End Bracket 1
Ladder Section 1Swing Bearings
Bottom Leg Section 2
Floor Boards 9
Slats 12 37 1/2" 2x4 Top 1
34 1/2" 2x4 Sides 2
Tarp Roof 1
10ft Wonder Wave Slide 1Roof Brackets 2
Belt Swings 2
Tower
Tarp Roof
Swing Frame
Accessories
Hardware
7
6
5
4
3
2
1
Threaded Rod
Threaded Rod
Threaded Rod
Threaded Rod
Step 2.
Step 3.
These are pre-drilled for the threaded rods, notice how the holes
Step 4.
holes.
Step 1.
hangers attached.
Step 6.
center and two shorter boards for each end.
Step 7.
joist.
Step 8.
threaded rods.
Step 5.
and acorn nuts.
Step 10.
head screws.
Use the included spacer to properly position them.
Step 11.
sections and a ladder section.
Step 12.
Place the bottom leg pieces on the legs and
Use two lags into each leg and one lag through the side brace.
Step 9.
fasten them with the same threaded rods.
holes are facing up.
Step 14.
Lift one end of the tower up and place one of the legs under it.
Step 15.
Step 16.
Step 13.
Lay the legs in position at each end of the tower.
Step 18.
Keep the side tabs even with the end of the 2x4 and attach it with
Step 19.
Center them and fasten them with the same washer head screws.
Step 20.
Step 17.
Locate these pieces to assemble the roof.
Finished Tarp Roof.
Swing Frame Assembly
Locate all the pieces for the swing frame.
Step 1.
One side is pre-drilled for the swing brackets, place the beam with
the holes facing up.
Step 21.
Unroll the tarp roof and place it in position over the center 2x4.
then stretch the tarp out with the second 2x4 and fasten it.
Step 3.
Locate the swing beam bracket and place it on the end of the
swing beam.
Step 4.
Locate the beam strap bracket and place it on the other end of
the beam.
Step 5.
Place the 4x4 end post in the bracket and fasten it with the same
threaded rods as the last step.
Step 2.
Fasten the swing bearings to the swing beam using the included
lags.
Table des matières
Autres manuels Yard Craft Équipements de jeux et d'aires de jeux
Yard Craft
Yard Craft Titan Manuel utilisateur
Yard Craft
Yard Craft Pluto Vinyl Playset Manuel utilisateur
Yard Craft
Yard Craft Backyard Cliff Climb Manuel utilisateur
Yard Craft
Yard Craft Cydonia Vinyl Playset Manuel utilisateur
Yard Craft
Yard Craft Orion Manuel utilisateur
Yard Craft
Yard Craft Hyperion Manuel utilisateur
Yard Craft
Yard Craft Lunar Vinyl Playset Manuel utilisateur
Yard Craft
Yard Craft Titan Playset Manuel utilisateur
Yard Craft
Yard Craft Polaris Vinyl Playset Manuel utilisateur
Yard Craft
Yard Craft Phobos Vinyl Playset Manuel utilisateur
Manuels Équipements de jeux et d'aires de jeux populaires d'autres marques
Ledon
Ledon 302040 Manuel utilisateur
FUNormous
FUNormous Disney Junior MICKEY MOUSE Manuel utilisateur
b4Adventure
b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Manuel utilisateur
PoolMaster
PoolMaster 72775 Manuel utilisateur
Palmako
Palmako 4743142009857 Manuel de l'installateur
BOERPLAY
BOERPLAY PSTE000.019 Manuel utilisateur
