Xvive Audio U3 Manuel utilisateur
SHENZHEN FZONE TECHNOLOGY CO., LTD.
2nd floor, Building 12, Xicheng Industrial Area, Xixiang Town,
Baoan District, Shenzhen Guangdong China. 518101
E-mail: [email protected]
MANUAL
MICROPHONE
WIRELESS SYSTEM
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK: DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTSINSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CERTIFICATION
This Class B digital apparatus complies with Canadian
ICES-003.
Radio Approvals: FCC Part 15.249, FCC Part 15 B, RSS-210
(Canada), EN 300 440 (Europe), EN 301.489 (Europe), MIC
Notice No.88 Appendix No.43(Japan)
01
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
WARNING:
Changes or modifications not expressly approved in writing
by Xvive may void the users authority to operate this equipment.
RF EXPOSURE STATEMENT:
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
NOTE:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC CERTIFICATION
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. There is no guarantee
that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following
MEASURES:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
02
1. Observe all instructions carefully in the U3 manual.
2. Do not to perform service operations beyond those
described in the U3 manual. Services required when the
apparatus has been damaged in any way, such as:
• Liquid has been spilled or objects have fallen into the
apparatus
• The unit has been exposed to rain or moisture
• The unit does not operate normally or changes in
performance in a significant way
• The unit is dropped or the enclosure is damaged
WARNING: BEFORE USING YOUR XVIVE U3 MICROPHONE WIRELESS SYSTEM,
CAREFULLY READ THE OPERATING INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS
IN A SAFE PLACE
3. Do not place near heat sources, such as radiators, heat
registers, or appliances which produce heat.
4. Guard against objects or liquids entering the device.
Do not use or place unit near water.
5. Clean only with a dry cloth.
6. Only use attachments/accessories specified by the
manufacturer.
7. Prolonged listening at high volume levels may cause
irreparable hearing loss and/or damage. Always be sure to
practice “safe listening.”
03
PRODUCT INTRODUCTION
• 2.4Ghz band is optimal for microphone wireless, approved
for use in Europe, South America, Asia and Australia.
• Less than 5ms Latency, Simultaneous broadcasts on 6
channels.
• Broad 20Hz – 20KHz frequency response
• Indoor range: Up to 90 feet (actual range depends on rf
signal absorption, reflection and interference )
• 5 Hours of battery life (rechargeable battery for both
Transmitter & Receiver)
• Works with dynamic microphone
• High Resolution 24-bit/48kpbs Audio
• Dynamic Range 110dB
• Signal to Noise Ratio is 110dB
• U3 wireless aims to take the complexity and frustration, out
of traditional wireless microphone systems. Creating a
flexible, all-in-one solution that makes any your favorite
microphones into wireless.
1PCS
1PCS
1PCS
1PCS
1PCS
U3 Transmitter
U3 Receiver
USB Cable
Manual
Bag
PACKAGE DETAILS
04
05
QUICK START
1. Plug the Transmitter into the Dynamic Microphone 2. Plug the Receiver into the Mixer.
06
QUICK START
3. Turn on the Transmitter and the
receiver and check the Channel.
4. After connecting successfully,
the LED lights on receiver will
stay on.
5. Check the connection by talking
through the microphone.
Hello!
07
1 Mic In – XLR microphone input jack
2 Spring - Circumferential ground spring providing an
accurate connection to the mating shell
3 Mic Lock – secures transmitter to the microphone
4 Input level switch – MIC = 0dB input;
LINE = -10dB input
5 Power switch – switches unit on/o�
6 Channel status LED - indicates selected channel
7 Channel switch - selects Channels 1-6
8 USB charging port
9 Power status LED - indicates power status:
Led off = 100% ~ 30%
Solid red = 29% ~ 11%
Flickering red = less than 10%
10 Antenna.
BASIC OPERATION
TRANSMITTER
2
3
4 5
1
7
8
9
6
10
08
1 XLR OUT - XLR microphone input jack
2 Power switch – switches the unit on and o�
3 Channel status LED - indicates selected channel
4 Channel switch - selects Channels 1-6
5 USB Port – For charging the battery
6 RF Status LED –
ON = Transmitter is on and link is established
Flashing = Signal connection interference
OFF = Transmitter o� or unlinked
7 Power status Led - indicates power status.
Led off = 100% ~ 30%
Solid red = 29% ~ 11%
Flickering red = less than 10%
8 Antenna.
BASIC OPERATION
RECEIVER
1
4
6
2
87
5
3
Autres manuels pour U3
1
Table des matières
