Xtreme Power Conversion SPD-0215 Mode d’emploi

SPD Switched PDU

SPD-0215, SPD-0815, SPD-1615 Models

User & Installaon Manual

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 2

Power Distribuon Unit

Table of Contents

System Descripon...................................................................................... 3

Front and Back Panel.......................................................................................................................4

Important Safety Precauons for Hardware Installaon...............................6

Safety Precauons.......................................................................................6

Baery Replacement.......................................................................................................................7

Access to the System....................................................................................7

Factory Default Sengs...................................................................................................................7

User Privileges and Port Reservaons.............................................................................................8

Local Master Port Access.................................................................................................................8

External Modem Access..................................................................................................................8

Telnet Access...................................................................................................................................8

Web Access......................................................................................................................................9

Email Access..................................................................................................................................10

SNMP Informaon.........................................................................................................................11

AutoPing and Power Reboot..........................................................................................................12

Using Control Command.............................................................................12

Using Conguraon Menu......................................................................... 14

Starng Conguraon Menu.........................................................................................................14

Viewing and Changing Operaon Status.......................................................................................14

Power Outlet Setup Menu.............................................................................................................15

Power Outlet Timer Setup Menu...................................................................................................16

User Account Setup Menu............................................................................................................18

System Access Setup Menu...........................................................................................................19

Serial Port Setup Menu.................................................................................................................20

TCP/IP Network Conguraon Menu............................................................................................22

More About TCP/IP Network Conguraon..................................................................................24

More about Emailing Access.........................................................................................................25

Appendix A: Serial Console Port Interfaces.................................................26

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 3

Power Distribuon Unit

System Descripon

MODEL NUMBER SPD-0215 SPD-0815 SPD-1615

Power cords 1 1 2

Power outlets 2 8 16

Power input IEC C14 inlet IEC C14 inlet (2) IEC C14 inlets

Outlet type (2) NEMA 5–15R (8) NEMA 5–15R (16) NEMA 5–15R

Input current 15A 15–30A 15–30A

Input voltage 100–240VAC

Dimensions (W x D x H) 5.4 x 6.0 x 2.5 in 19.0 x 7.0 x 1.75 in 19.0 x 7.0 x 3.5 in

Console port Baud rate: 115200; 8 data bits; no parity; 1 stop bit; no hardware handshaking

Ethernet 10/100 Base-T

Network protocol ICMP, IP, TCP, DHCP, Telnet, DNS, POP3/SMTP, SNMP, HTTP, and BootP

Display (6) LEDs (16) LEDs (24) LEDs

Operang temperature 32°F–122°F (0°C–50°C)

Storage temperature -20°F–140°F (-29°C–60°C)

Humidity 10–90%

WARRANTY 2 years (USA and Canada)

Model No. Total Outlets Input Voltage Input Feeds Max.Load

per Group

Max.Load

per Unit

SPD-0215 2 100-120VAC (1 ea.) 15 Amp 15 Amps 15 Amps

SPD-0815 8 100-120VAC (1/2 ea.) 15 Amp 15 Amps 30 Amps

SPD-1615 16 100-120VAC (2 ea.) 15 Amp 15 Amps 30 Amps

Key features include:

• Local Master Port access: oers data rates from 2400 to 115200 bits/second and oponal hardware hand-

shaking (CTS/RTS). There are two operaon modes for the port: Console Transparent and System Control.

• Three user privilege login levels: The Administraon level manages system conguraon and uncondi-

onal access to all power outlets and all serial ports. The User level allows each user to reserve and man-

age his/her own ports, as well as to change the most of system conguraon sengs. Anonymous users

are able to view all sengs and operate unreserved power outlets and serial console ports.

• User name and password for each port: The user name and password are protected in each ports.

• Line commands or menu conguraon controls: Menu table operaon oers user-friendly operaon

methods that are used for changing system conguraons, viewing run me statuses, and issuing controls.

Line commands provide quick and easy operaons.

• Telnet access: Remote access the system over a TCP/IP network for conguraon and systems control.

• Out of band Modem access interfacing: Control and congure the system via a telephone line. Oponal

custom Modem AT command string to the Modem.

• HTTP web access: Embedded web server provides secured user name and password authencaon. The

operaons are easy and friendly, ulizing tables and graphical icons. Download SNMP MIB les conve-

niently, or view the help manual on line.

• SNMP MIB capability: An SNMP (Simple Network Management Protocol) agent is integrated in the system

for an exchange of management informaon between the system and network devices.

• POP/SMTP Emailing with SMTP Authencaon capability: A user can send control commands such as re-

boot power outlet via emails. Command execuon reports are replied for each command email received.

SMTP user name and password are protected through authencaon process.

• SNMP Trap for sending logging message: The Trap is used to asynchronously report events to the NMS. It

forwards power reboot command execuon informaon to the remote Trap logging receiver.

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 4

Power Distribuon Unit

What you can do with the system:

• Remote equipment power source management over TCP/IP networks, including user equipment reboot-

ing, and permanently user power source turn on/o. Schedule power reboots or power source on/o

events monthly, weekly, daily or at any me. Reboot power source to equipment when a network connec-

on is lost.

• Monitoring AC Power Consumpons and sending warning messages when the aggregated AC draw from

a system is crossed predened threshold.

• Remote control anywhere by emailing. Via emails, you are able to manage the systems or user commu-

nicaon equipment power sources when LAN access is impossible. Via emails, you can send user data to

the NP control commands such as reboong user power source. Reply emails are sent aer the system

intercepts incoming emails so that you are informed with the operaon status.

• AutoPing and reboot user equipment. Connect your system to a power outlet and assign the system net-

work IP address or URL. The NP system will ping the user equipment Periodically (in every 15 seconds). If

the user equipment stops responding the ping request, the equipment will reboot the power.

• Scheduling AC outlet power cycling periodically or per weekly planner. Each outlet can be programmed

with it’s own mer.

Illustraon of Typical Applicaon

Front and Back Panel

SPD-0215 Front Panel

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 5

Power Distribuon Unit

SPD-0215 Back Panel

SPD-0815 Front Panel

SPD-0815 Rear Panel

SPD-1615 Front Panel

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 6

Power Distribuon Unit

1. Power Outlet status LED: Visual indicaon of user power outlet On/O status.

2. System power On/O status LED: Indicaon of system power On/O status.

3. Ethernet Link status LED: When the LED is illuminated, Ethernet port and a LAN connecon are established.

4. Ethernet speed status LED: Ethernet port have 100M status.

5. Ethernet Acve data status LED: When there is data trac on the LAN, the LED is illuminated.

6. Factory Upgrade switch: Allow the user to upgrade the system. The switch is located behind the small front

panel opening.

7. Factory Default Reset switch: Allow a user to reset the system to factory default sengs. The switch is located

behind the small front panel opening.

8. A and B Selecon LED: When the LED is illuminated, For Circuits A or B Amps which measurement will appear

on the Digital Displays.

9. Display Selecon Amps Indicators: When the LED is illuminated, Amps which measurement will appear

on the Digital Displays.

10. Display Selecon Temperature Indicators: When the LED is illuminated, Temperature which measurement will

appear on the Digital Displays.

11. Display Selecon Buon : Each me the Display Selecon Buon is pressed, the Digital Displays will toggle

Between Amps and Temperature, and the LED indicators will light to show which measurement is currently

selected.

12. Sensor Port: Temperature only or Temperature and Relave Humidity sensor are measured port.

13. Local Master Port (DCE, 9 pin DB, female, or RJ-45 socket): This is also a service port for the user to congure

and change system operaon sengs.

14. USB Port: For soware upgrade.

15. Ethernet Port (RJ45, 10/100 Base-T): 10/100 Based-T Ethernet port for connecon to LAN.

18. Digital Displays: Digital Displays will toggle between Amps and Temperature, and the LED indicators will light

to show which measurement is currently selected.

20. Power Circuit A - Power Inlet: An NEMA5-15P/IEC320-C14 AC inlet which supplies power (08 Series 1-4 outlets;

16 Series 1-8 outlets).

21. Power Circuit B - Power Inlet: An NEMA5-15P/IEC320-C14 AC inlet which supplies power (08 Series 5-8 outlets;

16 Series 9-16 outlets).

22. Power Breaker: System turn power on/o.

23. Power Circuit A - Switched Outlets: AC Outlets that can be switched On, O or rebooted in response.

24. Power Circuit B - Switched Outlets: AC Outlets that can be switched On, O or rebooted in response

Cauon: Sensor interface can be connected only with the sensor provided by the manufacture (Do not connect a

telephone line and so on).

Important Safety Precauons for Hardware Installaon

Safety Precauons

It is important that you read this secon before aempng any of the hardware installaon and maintenance

procedures in this guide.

The following instrucons are important for your safety and for the funcon of the unit. Read the instrucons

carefully before the installaon

WARNING!

To reduce the risk of re or electrical shock, never remove the cover of the unit. No user serviceable parts inside.

Repair should be done by authorized service personnel only. The unit should be installed in indoors with ambient

temperature and sucient airow.

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 7

Power Distribuon Unit

WARNING!

Please ensure the hardware to be disconnected with power supply for installaon. It means that the unit’s power

cable and network cables must remain disconnecon unl you are instructed to make the connecons. Follow the

instrucons in the procedures carefully. This equipment is requested to be disconnected from the power supply

by removing the power cord(s) from the power outlet. It is therefore important to locate the unit close to a power

outlet that is easily accessible.

WARNING!

To be safe, the unit must has the ground protecon.

Baery Replacement

A 3.0V Lithium recharging baery is installed in the unit for internal Real-Time Clock and system data retenon.

The baery should last recharging 1000,000 mes at least. If the baery needs to be replaced, please ask autho-

rized service personnel to do so.

Access to the System

Factory Default Sengs

The system is shipped with Factory Default sengs. The default sengs for the Local Master serial port are:

115200, 8 data bits, no parity, 1 stop bit, and no hardware handshaking (Flow Control).

The default Ethernet seng are: IP:192.168.1.100, GateWay:192.168.1.1, NetMask: 255.255.255.0

The default Administrator’s login name “admin” and the default password is “admin” and user’s login name “user”

and the default password is “user”. All exisng user accounts are erased if the system is recovered to the default

sengs. The default SNMP Community string for public, private and Trap access is “public”.

There are two ways to restore the system to the Factory Default sengs. The rst method is to press a push-buon

switch located on the front panel for 1 second. The second method is to select “Set Default Factory” from the Main

Menu. The Main Menu can be viewed by running a terminal emulaon program such as Window’s Hyper Terminal.

System Startup Screen

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 8

Power Distribuon Unit

User Privileges and Port Reservaons

All user levels, including anonymous (visitor), are able to access the system via a serial connecon from your work

staon to the Local Master port, or via a Telnet session from your work staon

Administraon Login:

There is 8 Administraon account at most on the system. The default name is “admin” and default password is

also “admin”. The default name and password may be changed. If you login at Administraon level, you are able to

remove or change exisng user accounts, take over power outlets or user serial console ports and change system

sengs.

User Login:

At user login level, you are able to reserve power or console ports for your applicaons if they are “open”, as well

as make system conguraon changes. At this login level, you are not able to change power outlet operaon status

for other reserved power outlets.

Guest (Visitor) Access:

At user guest level (as an visitor user), you are only able to view the system conguraon sengs and operate

unreserved power outlets.

Local Master Port Access

To access and congure the system from the master port, you need to connect a RS232 port from your work sta-

on to the Local Master Serial Port. Then run a terminal emulaon program (such as Window’s Hyper Terminal)

on your computer.

1. Connect the system’s Local Master Port (DCE) with a straight DB-9 type cable, if your work staon is

equipped with a DTE part.

2. Connect the system’s Ethernet port to your LAN, if you intend to use the network port.

3. Turn the system power on.

4. At the terminal emulaon program, type the “help” for help informaon.

5. The system has DHCP enabled, as a default seng. Network connecvity parameters displayed at the

startup screen. If the system does not get a DHCP oer,the system falls back to default stac network set-

ngs. You can alter the default network sengs to t your need.

6. Use the command “ping” to verify your connecon. If a network connecon is established, you are able to

use Telnet, Web Browsing, Emailing and SNMP.

External Modem Access

With this access method, an RS232 port on an external Modem device is connected to the Local Master Port. Typi-

cally, a Modem device is equipped with a DCE (Data Communicaon Equipment) terminal connector. Since the

system’s Local Master Port and Modem device ports are not complementary (both are DCE ports); you need to use

a NULL Modem cable with both male connectors.

Telnet Access

Operaon of on a Telnet terminal is almost idencal to the access method via Local Master Serial Port. You need

to make sure that Telnet access is enabled, as a default seng. If the access is not enabled, please refer to Secon

“Using Conguraon Menu” to change the seng.

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 9

Power Distribuon Unit

Before you start the Telnet applicaon, the user need to obtain the actual IP address for the system. The system

displays network connecvity informaon at system startup terminal when your workstaon is connected to the

system’s Local Master Serial Port. Please refer to “TCP/IP Network Conguraon” secon of this document for

informaon on how to setup the network parameters.

Once the network connecon is established, at your workstaon prompt, you need to enter:

telnet ip_addr

You need to set a Telnet session on your workstaon to Local Echo O mode.

Telnet session permits an anonymous user who may only to view the system sengs and operate unreserved

power outlets and user serial console ports. Please refer to “User Privileges and Port Reservaons” for further

informaon.

• There are 8 Telnet session at most may be acve at the same me.

• A Telnet session remains acve for 10 minutes if it is in idle state.

• Telnet access methods can be enabled or disabled using the System Access Setup Menu.

• To terminate an acve Telnet session, use the command “exit” at the terminal.

Telnet Session Startup Screen

Web Access

You need to obtain the system IP address before starng web access to the system. Please refer to the Telnet Ac-

cess secon for methods to get the system IP address. You also need to make sure that web access is enabled, as

a default seng. If the access is not enabled, please refer to Secon “Using Conguraon Menu” to change the

seng. Start a Web browsing applicaon program such as Window’s Explorer and enter “hp://ip_address“in the

address eld.

You must have an account on the system in order to access the system via this method. Without a valid account,

you are only able to view the following web page and get a copy of the Help text message.

Xtreme Power Conversion Corporaon

SPD User’s Manual

Page 10

Power Distribuon Unit

Web Access Startup Page

Upon clicking the Login buon, a secured login table is displayed at you work staon. Factory default seng for

user name is “admin”. The default password is “admin”.

Web Access Login Entry Table

Email Access

To establish this access method, the system’s network connecon is already established. With the email access

method, you are able to execute the NP system controlling commands. The NP system periodically checks incom-

ing mails from a designated POP mail server. The system sends a reply email with command process status if an

email is intercepted.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Xtreme Power Conversion Unité de distribution d'énergie

Xtreme Power Conversion

Xtreme Power Conversion XBDM Mode d’emploi

Manuels Unité de distribution d'énergie populaires d'autres marques

hager

hager SP 015 Manuel utilisateur

Pakedge

Pakedge PowerPak 9 Manuel utilisateur

Pts

Pts 9042 Series Manuel utilisateur

Shure

Shure WA405 Manuel utilisateur

CORNING

CORNING CCH 4U Manuel utilisateur

Panamax

Panamax M4LT-EX Manuel utilisateur

PANCONNECT

PANCONNECT FLAT 3M Manuel utilisateur

Raytheon

Raytheon 138-118 Manuel utilisateur

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manuel utilisateur

Botex

Botex PSA 322-6 DL Manuel utilisateur

GE QuiXtra 4000 Guide de démarrage rapide

RDL

RDL EZ Series Manuel utilisateur

StarTech.com

StarTech.com RKPW161915 Manuel du système

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manuel utilisateur

ABB

ABB PSBS0065 Manuel

Baumuller

Baumuller BFN 3-1-0007-001 Manuel

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manuel

GE GEK-45404F Manuel utilisateur