Xantech XT-DL-IRK Manuel utilisateur

XT-DL-IRK

DinkyLink™IR Receiver Kit

Plasma / LCD / LED / CFL Friendly IR Receiver

INSTALLATION INSTRUCTIONS

DESCRIPTION

These small IR receivers have been designed for mounting in very small spaces.

They may be mounted under shelf edges, cabinet ledges, in wall speakers, etc. –

anywhere an inconspicuous appearance is desired. The high sensitivity of these

receivers allows placement behind speaker grilles and still receive IR commands

up to 80 feet away*.

FEATURES

• Wire channel for clean installation.

• System testing red-talk-back LED.

• Includes 789-44 connecting block, power supply, two 283D, and two 286D

emitters for easy system installation.

• BOT-1.0 Break Out Terminator

SPECIFICATIONS

• Infrared carrier frequency bandwidth: 25 - 60 kHz.

• Reception range: Up to 80 feet.*

• Reception angle: +/- 60 degrees.

• Cable requirements: See “INSTALLATION” below.

• Max. Transmission length: 1 mile using 18 gauge wire.

• Maximum current output: 100mA.

• Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.

• Dimensions: 2.55” x 0.55” x 0.35” (65mm x 14mm x 9mm).

• Power requirements: +12VDC, 10mA.

*Depending on remote control output strength and ambient conditions.

MOUNTING

The IR receiver can be mounted to any at surface, using the two-sided adhesive

tape supplied.

An additional feature is a wire channel on the rear of the surface mount IR

receiver. This will give the installer the ability to provide clean wire dressing in

any direction.

INSTALLATION

QUICK-START

A typical system will use an IR receiver, several emitters, and a power supply all

connected to a connecting block.

1. Connect the IR receiver to the “IR RCVR” port on the connecting block.

The ‘red’ connector is installed to the ‘red’ plug. Note: In some extended

distances, additional 3-conductor may be required and can be connected to

the terminals on the connecting block.

2. Connect the Emitters to the connecting block. The ‘yellow’ connector is

installed to the ‘yellow’ plug.

3. Connect the power supply to the connecting block.

DL Series

IR Receiver

Red (or white)

Stripe

To 120 V AC

(unswitched)

781ERGPS

789-44

Connecting Block

REMOTE ROOM MAIN ROOM

Hand Hel d

Remote

3-Terminal Block (not included)

3-Conductor

Inter-room Cable

(unshielded OK)

7' Ribbon Cable

A/V Receiver

DVD

IR Photodiode

Red

Talkb ack LED

Satellite Receiver

283D Emitter

12VD C

+12 VDC

GND

STATUS

IR IN

EMITTERS

RCVR

789-44

CONNECTING BLOCK

IR OUT

+12V

GND

283D Emitter

PS12-0.5

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

DL Series

IR Receiver

DL Series

IR Receiver

DL Series

IR Receiver

Remote Room Main Room

789-44

Connecting Block

Satellite Receiver

3-Conductor

Inter-room Cable

(Unshielded OK)

283D Emitter

PS12-0.5

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

REMOTE ROOM APPLICATION

One application is to locate the IR receiver in a remote room. This will give the

end-user the ability to control audio/video equipment from a location where the

remote control no longer has the ability of direct line-of-sight.

The IR receiver will need the 3.5mm stereo type mini plug removed to extend the

wire run to the connecting block. A 4-terminal block is included to connect the IR

receiver to the connecting block with a 3-conductor inter-room cable in between.

The 3-conductor inter-room cable (24 gauge up to 200’, 22 gauge up to 600’, 20

gauge up to 2000’, 18 gauge up to 5000’), is run to the main room.

Input connections must be made as illustrated. To extend the emitter wires to

DL Series

IR Receiver

Red (or white)

Stripe

To 120 V AC

(unswitched)

781ERGPS

789-44

Connecting Block

REMOTE ROOM MAIN ROOM

Hand Hel d

Remote

3-Terminal Block (not included)

3-Conductor

Inter-room Cable

(unshielded OK)

7' Ribbon Cable

A/V Receiver

DVD

IR Photodiode

Red

Talkback LED

Satellite Receiver

283D Emitter

12VD C

+12 VDC

GND

STATUS

IR IN

EMITTERS

RCVR

789-44

CONNECTING BLOCK

IR OUT

+12V

GND

283D Emitter

PS12-0.5

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

DL Series

IR Receiver

DL Series

IR Receiver

DL Series

IR Receiver

Remote Room Main Room

789-44

Connecting Block

Satellite Receiver

3-Conductor

Inter-room Cable

(Unshielded OK)

283D Emitter

PS12-0.5

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

a more distant location, you may splice in 2-conductor wire, in the wire gauges

mentioned before, as needed.

While it is possible to make wired connections without the connecting block, it

is not recommended. The connecting block reduces installation time, helps to

eliminate errors, allows easy troubleshooting and permits easy system upgrades

later, if needed.

BOT-1.0 BREAK-OUT TERMINATOR

Use this unit to interface between the Quad (4-circuit) plug on Xantech Receivers

(so equipped) and 3 or 4-conductor inter-room wiring.

This eliminates the need to cut o the plug and strip and tin the leads for certain

applications.

DL Series

IR Receiver

Red (or white)

Stripe

To 120 V AC

(unswitched)

781ERGPS

789-44

Connecting Block

REMOTE ROOM MAIN ROOM

Hand Hel d

Remote

3-Terminal Block (not included)

3-Conductor

Inter-room Cable

(unshielded OK)

7' Ribbon Cable

A/V Receiver

DVD

IR Photodiode

Red

Talkback LED

Satellite Receiver

283D Emitter

12VD C

+12 VDC

GND

STATUS

IR IN

EMITTERS

RCVR

789-44

CONNECTING BLOCK

IR OUT

+12V

GND

283D Emitter

PS12-0.5

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

DL Series

IR Receiver

DL Series

IR Receiver

DL Series

IR Receiver

Remote Room Main Room

789-44

Connecting Block

Satellite Receiver

3-Conductor

Inter-room Cable

(Unshielded OK)

283D Emitter

PS12-0.5

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

LOCAL SYSTEM APPLICATION

Another application is to locate the IR receiver in a central location, such as

the TV, video screen and/or a speaker. The audio/video equipment can then be

hidden inside a cabinet or located away from the front of a room. This will give

the end user the ability to direct a remote control to one central location and not

have to worry about aiming to the respective device to be controlled.

The IR receiver is in close proximity to the audio/video equipment, no wiring

extension should be required so long as the connecting block is within reach of

the 7-foot cable. The 3.5mm stereo type mini plug is connected to the “IR RCVR”

jack on the Xantech Connecting Block.

PLACEMENT

The IR receiver should be located so that it is not directly facing a light source

such as lamps or displays (standard, LCD, and Plasma). When mounted near a

display, it should be ush to the display and away from light reections that may

occur.

DL Series

IR Receiver

Red (or white)

Stripe

To 120 V AC

(unswitched)

781ERGPS

789-44

Connecting Block

REMOTE ROOM MAIN ROOM

Hand Hel d

Remote

3-Terminal Block (not included)

3-Conductor

Inter-room Cable

(unshielded OK)

7' Ribbon Cable

A/V Receiver

DVD

IR Photodiode

Red

Talkb ack LED

Satellite Receiver

283D Emitter

12VD C

+12 VDC

GND

STATUS

IR IN

EMITTERS

RCVR

789-44

CONNECTING BLOCK

IR OUT

+12V

GND

283D Emitter

PS12-0.5

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

DL Series

IR Receiver

DL Series

IR Receiver

DL Series

IR Receiver

Remote Room Main Room

789-44

Connecting Block

Satellite Receiver

3-Conductor

Inter-room Cable

(Unshielded OK)

283D Emitter

PS12-0.5

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

DINKY-LINK (DL) IR RECEIVER KIT

DESCRIPTION

The DL Series Kit comes with everything needed for a complete IR repeater

system. With a Xantech IR Kit, equipment can now be concealed for clean

room design. In addition, a centralized IR receiver means there is only one IR

target resulting in improved remote control interaction. Featuring color-coded

connectors, a Xantech IR Kit is now an easy to install, and allows a worry-free

installation.

INCLUDED ITEMS

ITEM A: (1) DL Series IR Receiver

ITEM B: (1) 789-44 Connecting Block

ITEM C:

(2) 283D Single Designer Emitters

ITEM D:

(2) 286D Dual Designer Emitters

STEP 1:

Plug in the 2.1mm Coaxial power plug of the PS12-0.5 Power Supply (ITEM E)

into the jack labeled 12VDC on the 789-44 Connecting Block (ITEM B).

Plug the AC end of the PS12-0.5 Power Supply (ITEM E) into a ‘un-switched’

120V AC Line outlet.

STEP 2:

Connect the 3.5mm stereo mini plug from the DL IR Receiver (ITEM A) to the ‘IR

RCVR’ input located on the 789-44 Connecting Block (ITEM B).

The RED connector connects to the RED receptacle.

ITEM E:

(1) PS12-0.5

Power Supply

ITEM F:

(1) BOT-1.0

Break Out Terminator

STEP 3:

Plug in the 283D/286D Designer Emitters 3.5mm mono mini plugs (ITEM C/D)

into the jacks labeled EMITTERS on the 789-44 (ITEM B) and aix the opposite

end to the IR Sensor Window of the controlled equipment. Extra double sided

adhesive tape is included.

The YELLOW connector connects to the YELLOW receptacle.

PS12-0.5

Remote

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

Satellite Receiver

283D Emitter

286D

Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

12VDC

+12

VDC

GND

STATUS

IR IN

EMITTERS

789-44

CONNECTING BLOCK

RCVR

DL Series

IR Receiver

DL Series

IR Receiver

DL Series

IR Receiver

Remote Room Main Room

789-44

Connecting Block

Satellite Receiver

3-Conductor

Inter-room Cable

(Unshielded OK)

283D Emitter

PS12-0.5

283D Emitter

286D

Emitter

Blu-ray

A/V Receiver

Smart TV Box

Display 1 Display 2

IR TROUBLESHOOTING GUIDE

NOTE: Due to the many variables in a given installation, the troubleshooting

countermeasures you will have to take may vary from job to job. Each

installation is dierent due to the number of IR receivers in use, length of

wire runs, type of wire, amount of ambient IR noise present, etc…. Therefore,

your countermeasures for a particular job will range from nothing at all, to any

combination of the solutions listed below.

IR Receivers: Model #’s DL, HL, ML, and WL series

Cause Solution

1. Weak Batteries in Transmitting

Remote.

Replace batteries.

2. Bad Emitter or no emitter plugged

into connecting block.

Test emitter and verify wiring.

3. Signal wire between IR Receiver

and the Connecting Block is

open.

Recheck wiring.

4. Power Supply not putting out

proper voltage.

Verify supply is a 12VDC regu-

lated supply reading between 11.5

to 13VDC under load. Should be

using Power Supply Model PS12-0.5

(12VDC Regulated, 200mA) or PS12-

1.25 (12VDC Regulated, 1.2A)

5. Output from the IR receiver/

connecting block is connected to

a high impedance IR input jack on

a component.

If you are using a passive connecting

block, such as a 789-44, and the sys-

tem is not working, try the amplied

connecting block, model 791-44. Put

one of the small plastic case jumpers

supplied with the block on the pins

next to the emitter jack. This will pro-

vide the IR-in jack on the component

with a hotter signal.

6. IR Receiver is inoperable. Replace Receiver.

7. (XTRALINK Only) RF Amplier is

being used on same COAX Line

anywhere between the Coupler

(CPL94) and Injector (INJ94).

Need to use a Bypass Kit (model

BYPASS94 Kit) to route the IR control

signals around the amplier(s).

Symptom #1:

DIM or NO Talk Back LED during IR Reception or reduced operational range

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Xantech Récepteur

Xantech

Xantech ML25K Manuel utilisateur

Xantech

Xantech 29110D Manuel utilisateur

Xantech

Xantech XT-CAT-ARC-KIT Manuel utilisateur

Xantech

Xantech 490-85 KITRP Manuel utilisateur

Xantech

Xantech WL85 Manuel utilisateur

Xantech

Xantech Dinky Link 480B-30 Manuel utilisateur

Xantech

Xantech 490-85 Manuel utilisateur

Xantech

Xantech Micro Link 490D Series Manuel utilisateur

Xantech

Xantech Wall Link WL25 Manuel utilisateur

Xantech

Xantech 490-95 KITRP Manuel utilisateur

Xantech

Xantech 48085D Manuel utilisateur

Xantech

Xantech 480-95 Manuel utilisateur

Xantech

Xantech Dinky Link DL95 Manuel utilisateur

Xantech

Xantech ZA8REC Manuel utilisateur

Xantech

Xantech HL85 Manuel utilisateur

Xantech

Xantech 48195D Manuel utilisateur

Xantech

Xantech HL95 Manuel utilisateur

Xantech

Xantech HL25K Manuel utilisateur

Xantech

Xantech 780-10 Manuel utilisateur

Xantech

Xantech 780-80 Manuel utilisateur

Xantech

Xantech 291-10 Manuel utilisateur

Xantech

Xantech 291-80 Manuel utilisateur

Xantech

Xantech 291-95 KITRP Manuel utilisateur

Xantech

Xantech 291-455 Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur