X2E OABR2Ethernet Manuel utilisateur

OABR2Ethernet

Media Converter

User Manual

Version: 1.4 / December 2018

This user manual is protected by copyright; all usual rights reserved. Reproduction of this user manual, even in

part, is only permitted with the approval of X2E GmbH. Any infringement will result in liability for damages and

may result in criminal prosecution.

All product names and brands used in this user manual are the property of their respective owners.

User Manual OABR2Ethernet

Table of contents

Introduction.............................................................................................4

Intended use............................................................................................4

Delivery contents .....................................................................................4

General safety instructions......................................................................5

Product overview.....................................................................................6

Identification.............................................................................................6

Connections and control elements ..........................................................6

Installation.............................................................................................10

Mounting................................................................................................10

Connecting.............................................................................................10

CAN configuration and firmware update................................................12

Install XORAYASuite................................................................................13

Start Gateway configuration ..................................................................13

Buttons...................................................................................................14

Create and save configuration...............................................................15

Connect to converter .............................................................................15

Transfer configuration............................................................................16

Update firmware.....................................................................................16

Disconnect converter.............................................................................16

Cleaning................................................................................................17

Repair...................................................................................................17

Disposal................................................................................................17

Appendix...............................................................................................18

Technical specifications.........................................................................18

Pin assignments of the connection cable ..............................................18

User Manual OABR2Ethernet

Introduction

Intended use

OABR2Ethernet is an automotive media converter between OPEN Alliance BroadR-Reach®

(OABR) and standard Ethernet 100BASE-T. The device is primarily designed to convert

Ethernet signals between a car's ECU on one side and a PC or datalogger on the other.

You may only operate the converter within the scope of the technical specifications provided

in this user manual. Additionally, the use in hazardous areas is not allowed.

The converter meets the requirements of the EMC Directive of the European Union if the

connecting cable supplied is used. The interface connection lines may be extended up to a

maximum of 30 m, the voltage supply line, with sufficient cross section, up to 3 m.

You can find the declaration of conformity at the end of this user manual. Exact names of the

compliant product variants are available on request.

Delivery contents

OABR2Ethernet Media Converter

connection cable (optional)

user manual

XORAYASuite

USB driver

Check to ensure that the delivery is complete and all hardware components are in sound

condition. If the delivery is incomplete or supplied components are damaged, contact X2E

immediately. Do not use damaged components.

User Manual OABR2Ethernet

General safety instructions

The OABR2Ethernet Media Converter is only intended for use by qualified personnel. Read

the user manual and especially this chapter thoroughly before operating.

CAUTION

Electric shock due to damaged components

Damages to the converter or the connection cable can result in electric

shock.

Check all components regularly for damages.

Only connect the converter if all components are undamaged.

CAUTION

Device damage due to vibrations, dirt or liquids

Excessive vibrations, dirt or liquids may result in malfunction or destruction

of the converter.

Avoid exposing the converter to excessive vibrations, dirt or liquids.

Keep the converter clean, especially plugs and sockets to ensure a

reliable contact.

Never open the converter.

CAUTION

Device damage due to electrostatic discharge

Electronic components can be destroyed by electrostatic discharge.

Avoid touching connectors and connector pins.

Ground yourself before carrying the converter in your hands.

Operate the converter in an ESD-compliant environment.

User Manual OABR2Ethernet

Product overview

Identification

The identification plate is located on the bottom side of the OABR2Ethernet Media Converter.

It contains information about:

Typ device type

Rev hardware revision

S/N serial number

DMF date of manufacture

This user manual applies to the OABR2Ethernet Media Converter in hardware revision 1.01.

Connections and control elements

The front side contains LEDs, the service interface and the combined connection for power,

OABR and CAN.

The Ethernet interface and control elements are located on the back side.

Front view

Back view

User Manual OABR2Ethernet

Activity LED for OABR (A)

Colour Meaning

green interface ready

green (blinking) data transmission on this interface

yellow USB bootloader mode

Connection for power, OABR and CAN (B)

Pin Function

1 CAN_H

2 CAN_L

5 KL30(Ubatt)

6 KL31(GND)

7 OABR_N

8 OABR_P

Service interface (C)

Use the Micro USB interface to change the configuration or to update the firmware. For fur-

ther information, refer to the chapter CAN configuration and firmware update.

The pin assignments conform to the USB standard.

General status LED (D)

Colour Meaning

blue converter in initialisation phase

green converter ready

red error

User Manual OABR2Ethernet

LED for CAN (E)

Colour Meaning

blue interface in initialisation phase

green interface ready

red (blinking) activity on this interface

Link LED for OABR (F)

Colour Meaning

red connection established

yellow USB bootloader mode

Activity LED for Ethernet (G)

Colour Meaning

yellow (blinking) data transmission on this interface

Link LED for Ethernet (H)

Colour Meaning

green connection established

DIP switches (I)

No Function

1 switch the OABR interface between master (up) or

slave (down)

2 switch the OABR interface between full-out (up) and

half-out (down)

3 activate (up) or deactivate (down) sleep/wake mode via

CAN

User Manual OABR2Ethernet

Reset button (J)

This button is used to:

restart the converter

switch the converter into USB bootloader mode (further information in the chapter

Connect to converter)

Ethernet interface (K)

The pin assignments of the RJ45 connector conform to the Ethernet standard.

User Manual OABR2Ethernet

Installation

Mounting

CAUTION

Device damage due to overheating

Overheating may result in malfunction or destruction of the converter.

Do not operate the converter outside the specified temperature

range.

Do not operate the converter in the vicinity of heat sources.

Ensure adequate air circulation.

Do not cover the converter with other objects.

Mount the converter in such a way that it does not pose a hazard at any time.

Connecting

DANGER

Electric shock due to improper connection

Introducing the 4-mm plugs of the supplied connection cable into low-volt-

age sockets can be fatal.

Never introduce the 4-mm plug into low-voltage sockets.

CAUTION

Device damage due to wrong power supply

A wrong power supply can result in damage or destruction of the converter.

Only connect the converter to power supplies that correspond to the

technical specifications.

Pay attention to the correct polarity when connecting.

Disconnect service interface during standard operating mode

Make sure that the service interface (C) is disconnected in standard operat-

ing mode. Pull the plug if necessary and connect it again before changing

the configuration or updating the firmware.

Table des matières

Autres manuels X2E Convertisseur de média

X2E

X2E Automotive Ethernet Converter Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur