X10 WD13A Manuel utilisateur
1. INSTALL
ZONE
****
12:00 am
ENTER PIN
12:00 am Testing the Water Level Detector
• Dip the sensor pad into a cup of water. The Water Level Detector sounds its beeper
and will stop about 15 seconds later. If you are using a Security Console, its siren
will also sound (the Console does NOT need to be armed for the Water Level
Detector to trip it). Stop the Console’s siren with your keyfob remote, or disarm
from the Console by entering your PIN.
Installing the Water Level Detector
• Pry off the cover using a coin and attach the Water Level Detector to the wall using
the mounting screws provided, and replace the cover. (Fit the Water Level Detector
as high above the floor as the wire between it and the sensor pad allows).
• Place the sensor pad on the floor, or attach it to a wall (using double-sided tape) at
the height (level) you want water to be detected.
Using the Water Level Detector as a stand-alone item
If you don’t own the SC1200 Security Console, you can use the Water Level
Detector on its own. Just pry the two halves of the Water Level Detector apart using
a coin and install two AAAalkaline batteries inside. Observe polarity. The Water
Level Detector is then ready to use. It will beep whenever the sensor pad is immersed
in water (and stop beeping about 15 seconds later).
Initializing Water Level Detectors
1.Pry the two halves of the Water Level Detector apart using a coin
and install two AAA alkaline batteries inside. Observe polarity.
2.Press and hold the button inside the unit for 3-4 seconds and then
release it. This initializes the unit and picks a random code that is
used when it is registered with your Security Console.
3.Attach the water sensor pad to the two screw terminals.
Registering Water Level Detectors with the Security Console
Press either of the Menu up/down buttons (under the Console’s lid, to the right of the
display). The display then shows ENTER PIN (Personal Identification Number) in
the top line.
The default PIN is 0000, so press 0000 on the keypad, or enter your PIN if you
changed it (see Security System Owner’s Manual). This clears the top line and
shows * for each number entered.
This takes you to the first level of the menu at step 1. This is the INSTALLATION
level. When you see INSTALL on the display, press OK. The display then looks like
this:
Press and hold the button inside the Water Level Detector. The Security Console
acknowledges that it has been registered with a chime and by displaying RMOT 1
SET. Note, the Water Level Detector will also sound its beeper, wait for about 15
seconds for it to stop.
Repeat this for any other Water Level Detectors you want to register. The display
increments to RMOT 2 SET, etc, as you install more Water Level Detectors.
Beeper Press Clear to back out of the menus. You are asked to confirm, 1. YES, 2 NO.
Press 1 to go back to the HOME CONTROL screen. Press 2 to stay in the INSTALL
menu.
Battery Replacement
If the batteries get low the Water Level Detector beeps about once a minute.
Providing the batteries have not completely failed they can be replaced with two
AAA alkaline batteries without the need to reinstall the Water Level Detector into
the Security Console (if you’re using one). After removing the old batteries fresh
batteries must be fitted within 30 seconds to ensure that the security code is retained.
Testing the Water Level Detector
Once the batteries have been replaced, the Water Level Detector should be tested as
follows:
Dip the sensor pad into a cup of water. The Water Level Detector sounds its beeper
and will stop about 15 seconds later. If you are using a Security Console, its siren
will also sound (the Console does NOT need to be armed for the Water Level
Detector to trip it). Stop the Console’s siren with your keyfob remote, or disarm from
the Console by entering your PIN.
If the batteries had completely died, the security code will have been lost. You will
need to reinstall the Water Level Detector following the directions in this instruction
sheet.
FCC Statement
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOTCAUSEHARMFULINTERFERENCE,AND(2)THISDEVICEMUSTACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE
UNITS. ANY CHANGES MADE TO THE UNITS WILLVOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
Please visit: www.x10.com/support for additional help and warranty conditions.
Also see www.x10.com for more accessories that work with your Security System,
including Lamp Modules and Wall Switch Modules to flash lights when the alarm
trips, and remote controls that let you remotely control lights (and appliances)
connected to X10 Modules.
The X10 Supervised Security System includes a Security Console with an automatic
dialer that calls friends or relatives in the event of a break in. Accessories include
battery powered Radio Frequency (RF) Door/Window Sensors, battery powered
RF Motion Detectors, battery powered RF Water Level Detectors, and RF Keyfob
Remote Controls for arming and disarming the system. All sensors and remotes
incorporate random digital security coding.
The system can be configured with any combination of the following items:
• Up to 16* Wireless Keyfob Security Remotes with arm/disarm and panic
functions, and buttons to control security lights in and around the home.
• Up to 16* Wireless Water Level Detectors.
• Up to 30* magnetic switch operated Wireless Door/Window Sensors.
• Up to 30* Wireless PIR Motion Detectors.
• Optional X10 Home Automation modules such as plug-in lamp and appliance
modules and wired-in replacement wall switches can be added to the system.
The Owner’s Manual for the Security System describes the full installation process
for the Security System, and should be referred to in addition to these instructions.
*Note: Door/Window Sensors, and Motion Detectors, may be added in any
combination up to a total of 30, e.g. 15 Door/Window Sensors and 15 Motion
Detectors, or any combination up to a total of 30. There are also 2 hard wired
inputs, which are zones 31 and 32. Keyfob Security Remotes and Water Level
Detectors can be added in any combination up to a total of 16, e.g. 8 Keyfobs and 8
Water Level Detectors
X10.com, a Division of X10 Wireless Technology, Inc.
400 Forge Way, Suite 409-412, Rockaway, NJ 07866
WD13A-1/13
Water Level Detector
Model WD13A
Autres manuels X10 Capteur de sécurité
