wysLink WWC500 Manuel utilisateur
Solar powered Wi-Fi Camera
WWC500
User Manual
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 1
1. Introduction
1.1 Features
1. Use of solar power, and lithium batteries, which keep camera working all the time, when installed at
outdoor.
2. Microwave Motion Sensor， by which, the camera start to shoot video within 1 second when detect the
human or other object moving in covered range, and spontaneously send push notification to mobile APP;
3. Wake up from mobile app.
4. Supported 2.4GHz WIFI connection;
5. Manually switch night working mode, white-light source or infrared light source;
5. Automatically switch day / night mode, get clear video image at both modes.
7. Inductive Street light. The white lights will set on when there’s people detected within covered range
1.2 Appearance
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 2
1. Solar panel: Charge the lithium batteries in the unit; Please try best to install it in places under direct
sunlight, or use attached extender cable to install solar panel separately.
2. WIFI antenna: connect to WIFI router in WIFI mode, or Connect the mobile phone directly in AP hotspot
mode.
3. White-light source: two white lights at front . Automatically switch on at night when detect moving object in
covered area.
4. Infrared light: two infrared lights under lens at front. Automatically switch on during night time.
5. Light sensor: Sense the illumination, and judge as night time when less than 2Lus;
6. Lens: capture image video;
7. Microwave Motion sensor: When a person or a moving object is moving in front of the device, a trigger
signal will be generated and sent to the main unit;
8. Indicator Light:
White Light On: solar panel is charging the battery.
Green Light On: Sensed moving object
Red light flashes slowly: AP hot spot working and the system is waiting for configuration, or work as AP
mode.
Blue light flashes slowly: Working normally
Alternate flashing of red and blue: unconnected WIFI
9. Card slot waterproof cover: Please be sure to cover it properly.
10 Waterproof microphone
11. Power Switch: Power on camera at white light mode or infrared light mode;
12. Reset: Pressing and holding this button for 5 seconds, set camera to the factory setting (red light flashes);
13. TF card slot: 8G/16G/32G/64G are supported (Please format at FAT32 first before inserting);
14. USB port: For device updating.
1.3 . Specifications
Model/Name : Solar Powered Wi-Fi Camera
Model : WWC500-D2A-WD
Effective pixels : 2.0 megapixel
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 3
Resolution : 1920*1080
WIFI protocol: 2.4GHz， IEEE 802.11 b/g/n
Motion detection range : 0-10m/120 º
View angle : 78 º ( horizontal )
Working temperature: -20℃to 60℃
Working humidity: 0%-90%RH
Way of wake-up: HMD motion trigger / Remote APP wakeup by mobile phone
Power consumption : Daytime≤2W nighttime≤4W
Stand-by power consumption : 3mW
Solar panel wattage : 2.2W
waterproof grade： IP66
2. Installation, Settings
2.1 Set Camera Wi-Fi and add to App
1. Power on the camera
Open white rub cover at camera bottom, If use SD card, insert it before power on.
Slide the power switch to one side
Left side: Power on with infrared light mode.
Right side: Power on with white light mode.
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 4
2 . Download app "Tosee" from mobile app market and install it, open the APP, allow the app to accept
push notification.
3. Open the top right corner + of the APP to add device, select
Add a Device and enter the next step.
(Add a device shared from other, please select scanning QR code)
4. The red light of the device continues to flash Select the “Red
light has flashed” and go to the next step. (if the blue light flashes,
press and hold the reset button for 5 seconds to reset it to factory
settings).
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 5
Check the help message, then push “Go to setup to connect device”. Wi-Fi access points is displayed.
5. From the list, selecting the camera access point “TOSEE_xxxxx”, then click the bottom at top left, bring the
display to TOSEE app.
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 6
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 7
6. It shows connection icon at green, which means phone connect with camera directly. Puch “Next”, select
the target Wi-fi access point to which camera conntect, input the access password , then push “Next”.
7. Set the camera administrator password for the device, input the
device name, then push “Next”.
8. Return at main screen, the camera is listed. Click to to lanuch camera
main screen.
2.2 Share to others
Once it get connected, follow procesdure below to set at other phone.
At administer phone :
Click the Share key, enter the user nickname you want to share, and click "Confirm". QR code is displayed.
Hard copy it, send to the target phone.
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 8
At target phone which share to
Select “Scan QR code, start to scan the QR code by camera, or push “Photo Album”, load the QR image.
Once done, the camera will be on list as quest access.
2.3 Set parameters
Click icon , enter the settings page to adjust parameter, and view the device
information. Follow the item title and hint message.
- Video length
Select video length from 15, 30, or 45 second from list. If select Closed, it
mean no video clips are stored when motion is triggered.
3. Use App ToSee
3.1 View live
Before access the camera, make sure the camera is connected to Wi-
Fi network already. The no RED LED at front of camera is displayed.
After start the app ToSee, the devices are listed on main screen, click
the target camera thumbnail, the live view screen is launched.
Please noted that it take about 10 second to connect with camera
Solar Powered Wi-Fi Camera WWC500 User Manual V1.00 9
since it need wait for camera wake up.
Icon operations
Volume : control speaker on an off
Playback : Launch playback screen
Scene : Select video process mode
Closed: show raw video from camera sensor.
Backlight Compensation: Select it when background is very
bright, it make object at front bright
Infrared: force camera take night vision all the time
Highlight compensation: Select it when front is very bright
Motion Compensation : Get better video affection when
have motion.
Wide Dynamic range: Automatically adjust the video
dynamic range to get better video quality especially at
dawn or early morning
Screenshot: take picture and save it to photo folder.
Speaker : Not used at this camera. There is no speaker at the camera.
Record : push to start recording video on phone and push again to stop
recording. The video is stored at photo folder.
3.2 Play event video clip
It is to playback the video clips stored on SD memory card.
Push the calendar icon, select the date, all the videos of the day will be listed
up. Automatically played back from first one, then go to next.
Table des matières
Autres manuels wysLink Caméra de sécurité
