Wunda ESBE Manuel utilisateur
1
Before you start:
Check the contents
Check the pump station contents against the list below.
1. Top pump connector and flow
temperature gauge.
2. Circulating pump and washers.
3. bottom pump connector and return
temperature gauge.
4. ESBE Temperature control valve
There are two versions available:
VTA322 for 2-5 port manifolds up to 60oC
VTA572 for 6-12 port manifolds up to 70oC
This guide is specic to our ESBE temperature control pump station and should be used in conjunction with the relevant Manifold user guide.
1. Top pump connector and flow
temperature gauge.
2. Circulating pump and
washers.
3. bottom connector with return
temperature gauge.
4. ESBE temperature control valve.
*Small ESBE valve illustrated.
M11
ESBE Pump Station
✆ 0800 083 2677 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision date: 26-4-2018
In the unlikely event of any shortage please contact us and a replacement will be despatched immediately. Tel. 0800 083 2677
Understanding how the
ESBE pump station works
Warm water is pumped from the heat source to the pump set
and manifold assembly. If the floor heating system requires
a top up of heated water, the mixing valve will allow more
heated water into the system via the inlet or release cooled
water back to the heat source via the outlet. From the flow
bar, warm water is distributed to each loop of pipe via the
adjustable flow gauges, returning via the valves into the
return bar.
Once the room to be heated reaches the required
temperature, the room thermostat sends a signal to switch
the pump off and close the actuators (if actuators are fitted).
This shuts off the water supply to the loops of pipe in the
floor and therefore shuts off the heat supply.
Before assembly of manifold or pressure test, familiarise
yourself with the way the manifold works and the various
stages of assembly.
2
Flow Bar
Return Bar
Warm water from
heat source enters
Cool water returns to the heat
source for reheating
M11
ESBE Pump Station
✆ 0800 083 2677 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision date: 26-4-2018
This stage should be carried out by a suitably qualied professional. The same assembly steps should be followed for both small and large ESBE valves. It’s good
practice to use PTFE tape on every connection but beware not to over use. Hemp and Paste on connections is not advised.
Please refer to factsheet M04 for details of how to ll and pressure test the manifold.
Assemble top and bottom pump holders onto the
pump, ensuring pump washers are positioned correctly
Do-not overtighten pump connections at this stage.
.
Remove top and bottom pump holder adaptors from
the pump holders.
Screw the pump holder adaptors into the left hand end Flow and Return
bars tighten adaptors ensuring rubber O-rings are in place and seated
correctly against manifold bars forming a water tight seal.
3
Assemble bottom pump holder by connecting the
return temperature gauge, ESBE mixing valve and
pump connector.
M11
ESBE Pump Station
✆ 0800 083 2677 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Now the pump set and connectors can be attached to the manifold
via the adaptors. Ensure all connections are secured, tightened and
that all relevant washers and seals are correctly fitted.
Revision date: 26-4-2018
4
Adjusting the ow temperature
The temperature is increased or decreased by turning the control knob (1-6) . The higher a number is set will result in a higher
temperature reading, likewise lowering the number setting will decrease the temperature.
Example settings..
Solid/screed * 45C
Overfloor *35C
Multipanel * 45C
Joisted * 65C
These figures are only a guide, environmental conditions such as insulation levels, ventilation, room size will need to be considered
when setting temperatures.
Many floor finishes require limiting the floor surface temperature, this is achieved using a thermostat and floor probe.
Once required temperature has been achieved – replace the protective cap to the ESBE valve.
Flow rates and final manifold commissioning should be set in accordance with the correct manifold user guide.
The manifold and pump set can now be filled with water and commissioned in accordance with our user guide/video – manifold
pressure testing MO4. Ensure the pump is filled and vented, set floor heating to call for heat and then select desired pump setting in
accordance with pump user guide.
A good practice is to fit isolation valves when
installing the manifold & pumpset (sold seperately).
To protect floor surfaces and floor coverings it is
important to set the correct flow temperature for
your floor construction.
This ESBE temperature control valve must be set to
the specified temperature required and adjusted
to the required temperature shown in the‘Flow’
temperature gauge.
To adjust the control valve temperature first
remove the protective cap. (Small ESBE valve only)
M11
ESBE Pump Station
✆ 0800 083 2677 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision date: 26-4-2018
5
Temperature control supplementary information.
Floor surface temperatures
Before introducing heat into the floor heating system check with the
final floor finish supplier about maximum floor surface temperatures.
Generally a maximum floor surface temperature of 29ºC should not
be exceeded however many wooden floor finishes have a maximum
floor surface temperature of 27 ºC and must be layed in conjunction
with relevant underlay and moisture barriers.
We advise the use of floor probes in conjunction with room
thermostats be used in order to limit floor surface temperatures and
avoid damage to chosen floor finish.
In particularly large areas several probes and thermostats may be
required.
Wooden oor coverings
When installing wooden floor coverings over floor heating the floor
surface temperature must not exceed 27 ºC. Floor probes in
conjunction with room thermostats must be used in order to limit
floor surface temperatures and avoid damage to wooden floors.
Expansion gaps must be used to allow for expansion and contraction
movement of the wooden flooring as specified by flooring suppliers.
Birch and Maple are not suitable for use with floor heating due to
excessive amounts of expansion. Laminates and engineered woods
less than 25mm thick work well with floor heating. All wood flooring
products must be acclimatised to the heating system and its
operational temperatures by following suppliers guide lines.
WaterTreatment (required to comply with product guarantee)
Specialist water treatment suppliers such as Sentinal or Fernox will be
able to advise on all water treatment issues and dosage
requirements. Flushing should be in accordance with BS:7593 to
ensure awareness of the preparation of the water circuit for the wet
heating systems prior to initial commissioning following major
remedial work such as boiler replacement and the ongoing water
treatment to ensure continued efficiency. The water volume in a
16mm pipe Floor Heating system can be calculated by multiplying
the total linear length of Floor Heating pipe by a factor of 0.113 this
will give the volume of water in litres.
In order to minimise corrosion, treatment of the water with an
inhibitor is essential, however, for a corrosion inhibitor to function
effectively, the metal surfaces must be clean. The British Standard
Code of Practice BS 7593: 1992 details the steps necessary to clean a
domestic central heating system. The Code recognises that it is not
possible to clean a system without the application of a cleanser.
Different products may be used depending on the nature of the
system involved.
The most effective corrosion inhibitors act by reacting with the
surface of the metal to produce a protective film in the form of a
stable complex. The effectiveness of a given corrosion inhibitor will
depend on its concentration.
In a multi-metal system, the product selected should contain a blend
of inhibitors such that each metal is afforded good protection. In
addition to the usual metals and alloys, e.g., iron, copper, steel and
brass, special consideration must be afforded to aluminium.
Normally this metal is protected by a film of aluminium oxide which
prevents corrosion in water (or in air), but under acid or strongly
alkaline conditions the oxide film dissolves exposing the metal. Some
waters found in the UK will give rise to sufficiently alkaline conditions
in a central heating system to promote corrosion of aluminium and
the gassing associated.
An increasing number of central heating systems contain aluminium
so it is advisable that a neutral (neither acid nor alkaline) corrosion
inhibitor product is selected in every case.
Consideration should be given to adding antifreeze to the floor
heating system especially during the winter months.
All information in this publication is given in good faith, and believed to
be correct at time of going to press . No responsibility can be accepted
for any errors, omissions or incorrect assumptions. Users should satisfy
themselves that products are suitable for the intended purpose and
application.
Wunda Group Plc operates a continuous product
development programme to maintain our reputation for
quality products and as such we do occasionally modify or
amend the specification of our products in line with our
strict quality control policy. Maintenance of the floor heating
system is straightforward and the pump, manifold, gauges,
valves and actuators are designed for continuous operation
over many years. Wunda Group Plc recommends regular use
of floor heating systems, this will ensure flow gauges, pumps
and valves are kept in good working order.
Important
“When mixed floor solutions are being served from the same manifold, a
floor probe must be used in the floor solution with the lower maximum
supply temperature. This is to limit the temperature in these floor areas
and prevent damage to the floor solution and/or floor finish.”
M11
ESBE Pump Station
✆ 0800 083 2677 www.wundatrade.co.uk
THE BRAND YOU CAN TRUST
Revision date: 26-4-2018
6
Your Notes:
Tech support opening hours are subject to change - please visit our website for the latest information
Revision date: 26-4-2018
Autres manuels Wunda Pompe à eau
Manuels Pompe à eau populaires d'autres marques
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guide de dépannage
DUROMAX
DUROMAX XP WX Series Manuel utilisateur
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuel utilisateur
Franklin Electric
Franklin Electric IPS Manuel utilisateur
Xylem
Xylem e-1532 Series Manuel utilisateur
Milton Roy
Milton Roy PRIMEROYAL Manuel utilisateur