WS StealthPad Manuel utilisateur
58kHz Wifi StealthPadTM
Deactivator
Installation Manual
Version: 2022 Oct
Manual Part number: WG WF SP-IM
(221027C)
WG SECURITY PRODUCTS INC.
591 W.Hamilton Ave, Suite 260, Campbell, CA 95008 (USA)
Tel: 408-241-8000 ▪ Fax: 408-559-2073
Technical Support Contact Information
North America
South America
Rest of World
WARRANTY DISCLAIMER
WG Security Products Inc. makes no representation or warranty
with respect to the contents hereof and specifically disclaims
any implied warranties of merchantability or fitness for any
particular purpose. Further, WG Security Products Inc. reserves
the right to revise this publication and make changes from time
to time in the content hereof without obligation of WG Security
Products Inc. to notify any person of such revision or changes.
CRITICAL NOTE
As specified by FCC Regulations 15.21, any changes or modifications not
expressly approved by the party responsible for compliance of this equipment,
will void the user’s permission and authority to operate this equipment.
FCC ID: 2A8TVWGWFSP58-II
“This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.”
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
IC: 29378-WGWFSP58II
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
l'appareil contient des émetteurs/récepteurs exempts de licence qui sont
conformes aux CNR exempts de licence d’Innovation, Sciences et
Développement économique Canada. L’exploitation est soumise aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage,
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
Conformément àla réglementation d'Industrie Canada, le présent émetteur
radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou
inférieur) approuvépour l'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique àl'intention des autres
utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire àl'établissement d'une communication satisfaisante.
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your
body.
ce matériel est conforme aux limites de dose d'exposition aux
rayonnements, CNR-102 énoncée dans un autre environnement.cette
eqipment devrait être installéet exploitéavec distance minimale de 20
entre le radiateur et votre corps.
TABLE OF CONTENTS
OVERVIEW ............................................................................................................................... 1
System Description.................................................................................................................... 1
Features..................................................................................................................................... 1
Specifications............................................................................................................................. 2
PRE-INSTALLATION GUIDE ................................................................................................... 3
CAD Dimensions ....................................................................................................................... 3
Flush Mount Cut Out Suggestion .............................................................................................. 4
Installation Site Power Supply Check........................................................................................ 5
INSTALLATION ........................................................................................................................ 6
Parts List.................................................................................................................................... 6
Deactivator Components and Connections............................................................................... 8
Power Cord Notices................................................................................................................... 9
North American Power Supply Cords ................................................................................ 9
International Power Supply Cord ....................................................................................... 9
Fuse replacement.................................................................................................................... 10
QUICK START INSTRUCTIONS............................................................................................ 11
General Setup and Use........................................................................................................... 11
WGcloud DigiToolClient Communication Connection Setting Instruction............................... 12
Wifi StealthPad Installation Manual
1
OVERVIEW
System Description
StealthPad is a distance deactivator providing excellent deactivation reliability and high
throughput. The StealthPad can be easily installed on the counter top or flush mount.
StealthPad deactivates AM labels up to 5 cm (2 in.) above the surface of the pad at a high
throughput speed.
Features
Compactness
Its small footprint makes the antenna especially attractive in small counter tops or
where counter space is at a premium.
Proximity Deactivation
The StealthPad offers distance deactivation, making it perfect for both source tagged
and retailer tagged merchandise.
Compact Size
The compact size of the deactivation antenna allows StealthPad to easily be
integrated into a counter application.
Integrated Audible and Visual Notification.
Label deactivation notification is built into the StealthPad.
Cloud Accessible
StealthPad includes the remote access capability via WG’s optional Cloud TM
software for a variety of remote controls and data mining.
Wifi StealthPad
Double Resonant Labels
Wifi StealthPad Installation Manual
2
Specifications
Electrical
Primary Input
115/230 10% @60Hz/50Hz (Input)
Rated Current
0.3A/5A
Transmitter Output
1.6ms Burst
Transmitter Current
0.3A Peak (Nominal)
Operating Frequency
58kHz
Mechanical
StealthPad Antenna
Height
236mm (9.3”)
Width
186mm (7.3”)
Depth
64mm (2.5”)
Weight
1.5kg (3.3 lbs)
Wifi Antenna
Length
108mm (4.3”)
Width
10mm (0.4”)
Weight
15g (0.033 lbs)
Environmental
Operating Temperature
0 to 49C (32to 120F)
Relative Humidity
0 to 85% non-condensing
Wifi StealthPad Installation Manual
3
PRE-INSTALLATION GUIDE
CAD Dimensions
StealthPad(All dimensions are in millimeters)
Wifi StealthPad Installation Manual
4
Flush Mount Cut Out Suggestion
Wifi StealthPad Installation Manual
5
Installation Site Power Supply Check
IT IS RECOMMENDED THAT ALL STEALTHPADS BE ON THE SAME POWER PHASE.
Otherwise you need to adjust B sync value step by step to find a best position to sync
different StealthPads when connected to power sources with difference phases.
ENSURE THERE IS SUFFICIENT CURRENT SUPPLY IF MULTIPLE STEALTHPADS
SHARE ONE POWER SOURCE. The rated current for StealthPad is 0.3A but the
suggested current draw for one StealthPad is 1A for better performance, so a 15A power
box will better serve 10 StealthPads instead of 15 or more.
ENSURE THERE IS GOOD GROUNDING FOR THE STEALTHPAD POWER SUPPLY.
Sometimes poor grounding and high noise from the power supply will lower the sensitivity
or detection range.
Wifi StealthPad Installation Manual
6
INSTALLATION
Parts List
Part Name
Order Number
Wifi StealthPad for 110VAC power voltage
Wifi StealthPad for 220VAC power voltage
Wifi Antenna
WG WF SP 58-II 110V
WG WF SP 58-II 110V B
WG WF SP 58-II 220V
WG WF SP 58-II 220V B
Wifi SMA Antenna
Antenna (1)
Wifi Antenna (1)
Table des matières
