Wosports LY-121 Manuel utilisateur

User’s Guide for Trail Camera

Thanks for purchasing this trail camera. Please read this instruction manual carefully

before using this product.

Please carefully unpack camera and check that below accessories are

contained in the box.

①. Trail camera x1

②. Instruction Manual x1

③. Mounting Belt x1

④. Wall Mount x1

⑤. Screws x3

Packing List

Manual

① ② ③ ④ ⑤

locking bracket

Product Structure

567

8 9

① LED lamp

② Lens

③ LED lamp

④ PIR

⑤ SD card slot

⑥ Power key

⑦ Display

⑧ Down key

⑨ UP key

⑩ OK key

1. Install 4pcs AA batteries (NOT INCLUDED).

2. Install SD card (CLASS 6 or higher class Up to 32GB max, NOT

INCLUDED).

3. Put the switch to "AIM", then you can setting(Time/ Date, Interval

Time etc).

4. Put the switch to the “ON” position, The notion indicator LED will

blink red for about 10 seconds. Then shut down; it will enter the PIR

detection state. the trail camera starts working.

Note:

1. Be sure to switch the camera’s power OFF before inserting /exiting

the SD card and loading/unloading the batteries.

2. Formatting the SD card before using it for the first time is

recommended. (Put the switch to "AIM " --Press OK key to skip to

"FOrn" page and use UP/DOWN to change the “N” after “FOrn_”to “Y”

-- Press OK to format the SD card . )

3. A full set of 4AA Alkaline or Lithium batteries is recommended.

The Camera Operating

HOW TO USE?

1. Open the locking bracket ,you can see the battery compartment inside

the camera.

2. Please loading batteries. Be sure to inset each battery so its polarity

(+/- direction) matches the polarity indications at the bottom of the

battery tray (Fig1).

Note:

1. NiMH Rechargeable batteries are not recommended.

2. 4 new batteries are recommended. Mixed old and new batteries are

not recommended.

3. Battery scrapping and recycling Please strictly abide by local

government policies and laws. We are not responsible for any

incidents of danger and violation of local regulations due to improper

battery disposal.

Loading Batteries

Fig1

bat tery b att ery b atte ry ba tter y

- + - +

+ - + -

Make sure that the SD card is insert correctly. If you hear “click” sounds

that means it has be inserted correctly .If the SD card is not inset

correctly, or no card is in the slot,”CArd” will appear on the LCD display

(Fig2), and please reinsert the SD card. Other card status display

message:”FULL” (Fig3) indicates the card’s memory is full, with no

remaining room to store files. (Fig4)“Err” means there is a card reading

error (please try a different SD card ).

Inserting SD Card

Fig2 Fig3 Fig4

Using the camera and Setup

Using the camera

1. Operating buttons 1

① UP key: page up

② Down key: page down

③ OK key: confirm the setting

④ ON key: working mode

⑤ AIM key: setup mode

⑥ OFF key: stop working mode

2. Power/Mode Switch Operation Instruction

Slide the switch to choose work mode:

OFF Mode: The camera’s power switch is in the OFF position. (The

camera is turn off and does not work )

AIM Mode: The camera’s power switch is in the AIM position(The

screen is on, enter setup mode)

ON Mode: The camera’s power switch is in the ON position.(The

camera ready to work and the screen will turn off after

10 seconds)

OFF Mode

The OFF mode is the safe mode when any action must be taken. Please

be sure the camera’s power is switched OFF before you replacing the

battery, removing or inserting SD card, or transporting the device. And

of course, when you are storing or not using the camera, you will switch

it OFF. Please note that even in OFF mode the AUTOPILOT camera

still consumes power at a very low level. Therefore, it’s a good idea to

take the batteries out the battery compartment if the camera will not be

used for a long time

ON Mode

Please be sure the batteries were loaded and SD card was inserted,

and placed the camera to the right induction height or area ,then, move

the mode switch to ON mode. The notion indicator LED will blink red for

about 10 seconds. This interval allows time for you to close the Cam’s

front cover, lock it ,and leave the monitored area. Please note that you

can’t manually setup parameters once in ON mode. The camera will

take pictures or videos automatically.(According to its current slide

switch settings) when it is triggered by the PIR sensor’s detection of

activity in the area it covers. You can either move the power switch

directly move from OFF to ON mode, or stop at the setup position first to

change one or more settings, then move the switch to ON after you have

finished doing so.

AIM Mode

Move the Power switch to the AIM position. It means that the device is

going into setup mode. You can check and change the settings of the

camera in the setup mode, such as the image resolution ,the video

resolution, and the interval time etc.

Note: Always move the power switch from OFF to AIM mode. It is

possible that the camera could would lock up if it is switched from ON to

AIM mode. If this occurs, simply move the switch to OFF and then push

it over to AIM again.

Setup

Once batteries are installed and an SD card is inserted, you are ready

to go into the setup mode to get the camera ready to use, with all

options set to your preference. There are only a few settings to make,

so the process is quick and easy. To start setting up your camera.

1. To enter Setup mode, move the power switch to the middle(AIM)

position ,You can see that the display will come on and show the

initial setup screen. So that you can set and change the camera

parameters as you want.

2. Press the OK key to begin .You can press UP or Down keys to change

the setting of the currently selected option or item. Press OK to

confirm that you choice .When you finish changing a setting, press

OK to lock in the setting and move on to the next option. If there is a

setting that you don’t need or want to change from the default or

current setting, simply press OK to confirm and skip to the next item.

Setting Time and Date

After the Initial setup screen, the next few display screens will allow you

to set the current time and date, so the time/date stamp imprinted on all

your photos and videos will be accurate when captured by the camera to

change the time and date to be current, starting at the current time show

on screen.

1. Press OK and use UP/DOWN to set the hour. Press OK to confirm

(Fig5).

2. Use UP/DOWN to set the minute. Press OK to confirm(Fig5).

3. Use UP/DOWN to set the month .Press OK to confirm(Fig6).

4. Use UP/DOWN to set the date. Press OK to confirm(Fig6).

5. Use UP/DOWN to set the year. Press OK to confirm and move on to

the next setup item(Fig7). Like setting(see figure below).

Fig5 Fig6 Fig7

Setting Capture Mode and Image /Video

Resolution

Table des matières

Autres manuels Wosports Caméra de repérage

Wosports

Wosports Wosoda G200 Manuel utilisateur

Manuels Caméra de repérage populaires d'autres marques

Nestbox

Nestbox C13 Manuel utilisateur

Wildview

Wildview STC-TGL1 Manuel utilisateur

Stealth Cam

Stealth Cam CORE STC-Z3IRTL Manuel utilisateur

Suntek

Suntek HC-800M Manuel utilisateur

Spypoint

Spypoint G4 Manuel utilisateur

Duramaxx

Duramaxx 10029765 Manuel utilisateur

Brecom

Brecom C2400 Manuel utilisateur

BlazeVideo

BlazeVideo A280W Manuel utilisateur

Bestok

Bestok 5210GM Manuel utilisateur

GardePro

GardePro X60P Manuel utilisateur

Delta-Opti

Delta-Opti HC-SG880MK-18MHD Manuel utilisateur

PNI

PNI HUNTING 280C Manuel utilisateur

Muddy

Muddy Pro-Cam 14 Manuel utilisateur

Bresser

Bresser 3310006 Manuel utilisateur

Recon Outdoors

Recon Outdoors HS410 Manuel utilisateur

Braun

Braun 57660 Manuel utilisateur

Wildgame

Wildgame Shadow Manuel utilisateur

Spypoint

Spypoint FLEX Manuel utilisateur