WorkPro LM 3E Guide de configuration
Rev. 13.10.01
Quick Start User Guide
0. SAFETY INFORMATION & MAINTENANCE
Read this manual before powering or installing the device, follow the safety precautions listed below and
observe all warnings in this manual.
•Be sure that the local power outlet matches that of the required voltage of the power supply included
with this device.
•To reduce the risk of fire or electrical shock, do not expose the unit to rain or high levels of moisture.
•Do not spill water or other liquids into or on your unit.
•Do not open the unit as there are no user serviceable parts inside.
•Do not dismantle or modify the unit, as this voids all warranties.
•Do not attempt repairs. Repairs by unqualified people could cause damage or faulty operation.
Contact your local authorized service center.
•Unplug this unit when not used for long periods of time.
•Clean only with dry cloth.
•Handle this unit carefully. Any strong shock or vibration may result in malfunction.
LM 3E - 1 -
User Manual/Manual de Uso
EN
1. DESCRIPTION
LM 3E
a compatible Ethernet signal, and transmits the resulting si
this way, the converted DMX signal can be received by on
will convert it into DMX signal again, in order to control compatible devices.
LM 3E
users, network configuration can be modified using the web-based management interface, as seen before in
this document.
LM 3E has a DMX input, and one LAN connector that provides an Ethernet interface for one DMX universe.
LM 3E also has a group (universe) selector that allows to select up to 16 different groups or DMX universes.
is a which captures the DMX signal from a DMX console, converting it into DMX to Ethernet converter
gnal to an Ethernet local area network (LAN). In
e or more receivers connected to the LAN, which
is a plug and play
device and does not need any network configuration. However, for advanced
1.1 ART-NET
As Art-Net device, LM 3E must be used in combination with an ArtNet node, such as LM 3R configured in the
same SubNet and Universe.
LM 3E converts the DMX signal, from the DMX console, into an Art-Net signal,
and transmits this signal to the Ethernet network. The Art-Net node will capture t
Ethernet network, and will convert it into a DMX signal again.
he Art-Net signal from the
LM 3E - 2 -
User Manual/Manual de Uso
EN
Sub-Net Sub-Net
LAN
ETHERNET
DMX CONSOLE
LM 3E
DMX frame
DMX frame
LM 3R
DMX DEVICES
Both devices set in the same SubNet and Universe
1.2 WEB CONFIGURATION
As seen before, LM 3E is a plug and play device. By default, it is automatically configured like an ArtNet
device, with an IP address 2.x.x.x and SubnetMask 255.0.0. Each LM 3E has a sticker at the bottom with its
default settings.
Although LM3-E is plug and play, it offers a user-friendly web-based management interface for the
configuration of the network features, and another parameters. To connect to the web interface, you must set
your PC IP address to be on the same subnet as the LM 3E (that is, the PC and LM 3E addresses must both
start 2.x.x.x, with subnet mask 255.0.0.0). Then, to access the configuration menu use your web browser to
connect to the management interface using the default IP addres, shown in the sticker at the bottom of the
device. (http://2.x.x.x)
The web interface allows to change the IP Address and the Subnet Mask
If the IP Address is modified, it is very important to remember the new one, in order to can connect the next
time you access the web interface. Anyway, it is possible to connect using the default name (http://lm3e.local/) the first time
If you change the device name, type the new name instead of lm3e
Fig.1 The integrated WEB SERVER
.
.
allows the configuration of the unit
1. The CURRENT STATUS section show us all connection information (IP address, name, MAC address, and
Firmware version).
2. The NETWORK SETTING section allows to rename the device in order to identify it. Be carefulwith this function due to
you need to remember the device name in order to access to the webserver again. In this section it is possible to select
the IP and its Subnet.
3. When you finish to set it, press SAVE NETWORK SETTINGS to store the changes.
LM 3E - 3 -
User Manual/Manual de Uso
EN
2. FRONT PANEL
Sub-Net ARTNET/LAN USB 5VDC
LM 3E - 4 -
User Manual/Manual de Uso
3. Power LED: This LED lights when the unit is powered.
4. Plug In power connector: the device can be powered with the provided power supply by
using this connector. If this is used, then the Micro USB connector (5) MUST NOT
be used.
1. Activity LED: This LED blinks when any activity is detected in the Ethernet network.
2. Link LED: This LED is turned on when an Ethernet network is detected (Ethernet connector
is plugged).
Micro USB power connector: the device can be powered with a power supply of 5V DC,
NOTE: Remember, this port is ONLY for power supply purpose.
ARTNET/LAN: RJ45 connector used to connect the device to an Ethernet network.
Sub-Net / Universe selectors: In Art-NET mode, this selector allows to select up to 16 Sub-Nets
and 16 Universes rotating the selector between 0 to F.
5.
6.
7.
EN
8. DMX OUT: This XLR-5 male connector is the DMX in signal. It receives DMX frames to
DMX compatible devices like moving heads, scanners,RGB drivers, amplifiers, etc. from
a DMX compatible console.
4. LM 3E CONFIGURATION
3. REAR PANEL
IN
B. Select the Sub-Net and Universe with the selectors according to installation requirements (7).
C. Plug in a CAT 5 cable in the Ethernet/LAN connector (6).
D. Plug in a XLR 5 female cable in the DMX IN connector (8) from the DMX console.
E. Plug the included power supply or use a micro USB power supply or use a micro USB cable
to supply the unit from a standard USB port. The POWER LED (3) will lit immediately. After
some seconds, if the device is plugged to a network, the ACT LED (1) and the LINK LED (2)
will begin to blink.
LM 3E - 5 -
User Manual/Manual de Uso
EN
LM 3E - 6 -
5. USING OSCillation software (Firmware updating process)
OSCillation is a software which offer several prefixed layouts in order to generate DMX frame in
order to control de devices connected in a LM 3R or LM 5.
Also, this software allows to updated the firmware of the LM series devices and offer all information
about this device (MAC address, IP, etc). This feature is very useful in case of we do not remember
the name of the device o we want to confirm its IP address.
The link to download this software is the following:
http://www.equipson.es/prodDetail.asp?idproducto=1889#
Set the PC ethernet connection in the range 2.x.x.x
NOTE: If you connect LM 3E to a PC directly. You need to use a CROSSOVER cable
User Manual/Manual de Uso
- Press View tab in the uper side of the interface and, after, press Devices. An additional
window will offer the devices found in the same LAN (LM-3E MKII in that case).
- In the right window, we can check all information about this device like firmware version, MAC
address, IP address and name. This point is very important in the case of we lost the name of the
device. Simply using this apliance, we can check and comfirm this information.
- Update button allows to update the firmware version when it was available.
- Activate button allows to use the interface to control the device. Press it and check that using the
faders, the value number change according the movement.
NOTE: This sections IS NOT enabled using a LM 3E.
EN
LM 3E - 7 -
User Manual/Manual de Uso
Lea este manual antes de encender o instalar el dispositivo, siga las instrucciones de seguridad listadas a
continuación y observe las precauciones citadas en este manual.
•Asegúrese de que la toma de corriente local coincide con la tensión necesaria de la fuente de
alimentación incluida con el dispositivo.
•Para reducir el riesgo de incendios o descargas eléctricas, no exponga la unidad a la lluvia o niveles
altos de humedad.
•No derrame agua u otros líquidos al interior o dentro de la unidad.
•No abra la unidad ya que no hay piezas que el usuario pueda reparar.
•No desmonte ni modifique la unidad, ya que anula todas las garantías.
•No intente reparaciones. Las reparaciones efectuadas por personal no cualificado pueden causar
daños o un funcionamiento defectuoso. Póngase en contacto con su centro de servicio autorizado.
•Desenchufe la unidad cuando no se utilice por periodos prolongados de tiempo.
•Limpie sólo con un paño seco.
•Transporte esta unidad con cuidado. Cualquier golpe o vibración pueden provocar un mal
funcionamiento.
ES
LM 3E - 8 -
User Manual/Manual de Uso
ES
1. DESCRIPCION
LM 3E es un conversor DMX a Ethernet, el cual captura la señal DMX procedente de una consola DMX,
convirtiéndola en una señal Ethernet compatible y transmitiendo la señal resultante en una red local (LAN).
De esta manera, la señal DMX convertida puede ser recibida por uno o varios receptores conectados a la
red LAN, los cuales la convertirán de nuevo en señal DMX con el fin de controlar dispositivos compatibles.
LM 3E es un dispositivo plug and play y no necesita ninguna configuración de red. De todas formas, para
usuarios avanzados, la configuración de red puede ser modificada utilizando un interfaz de manejo basado
en web (webserver), el cual se muestra en este documento.
LM 3E tiene una entrada DMX y un conector LAN que proporciona un interfaz Ethernet para un universo
DMX. LM 3E también tiene un selector de universos que permite seleccionar hasta 16 universos.
1.1 ART-NET
Como dispositivo Art-Net, LM3 E debe ser usado en combinación con un nodo ArtNet, como LM 3R
configurado en la misma SubNet y Universo. En este modo, LM 3R convierte la señal DMX de la consola
en señal ArtNet y la transmite a la red. El nodo LM 3R captura la señal correspondiente al mismo universo
desde la red y la convierte en señal DMX de nuevo.
Sub-Net
Sub-Net
LAN
ETHERNET
CONSOLA DMX
LM 3E
Trama DMX
Trama DMX
LM 3R
DISPOSITIVOS DMX
Ambos dispositivos configurados en la misma SubNet y Universo
Table des matières
Langues :
Manuels Éclairage domestique populaires d'autres marques
JONATHAN Y
JONATHAN Y JYL5019A Manuel utilisateur
JONATHAN Y
JONATHAN Y JYL6007A Manuel utilisateur
Philips
Philips Ledino 31606/11/16 Manuel utilisateur
Salus
Salus UG600 Manuel utilisateur
Safavieh Lighting
Safavieh Lighting CANDRI TBL4427A Manuel utilisateur
Hunter
Hunter Bullet Spotlight Kit Manuel d'instructions
