Wolf ICBWWD30 Manuel utilisateur

WARMING DRAWER

INSTALLATION INSTRUCTIONS

CAJÓN CALENTADOR INSTRUCCIONES DE INSTALACIÓN

TIROIR CHAUFFANT INSTRUCTIONS D’INSTALLATION

CASSETTO SCALDAVIVANDE ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

ENGLISH 4

ESPÃNOL 22

FRANÇAIS 40

ITALIANO 58

DEUTSCH 76

As you follow these instructions, you will

notice WARNING and CAUTION symbols.

This blocked information is important for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

Record the model and serial numbers before

installing the warming drawer. Both numbers

are listed on the product rating plate, located

on the left front floor area of the inner cabinet.

To access the rating plate, the drawer must be

fully open. Refer to the illustration below.

Model Number ICBWWD30

Serial Number

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

This installation must be

completed by a qualified technician.

Installer:

Please read the entire Installation

Instructions prior to installation. Save these

instructions for the local inspector’s refer-

ence, then leave them with the homeowner.

Homeowner:

Please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

Any questions or problems about the

installation should be directed to your Wolf

dealer. You can also visit our website

at wolfappliance.com.

IMPORTANT NOTE:

This appliance must be

installed in accordance with local codes. The

correct voltage, frequency and amperage must

be supplied to the appliance from a dedicated,

grounded circuit which is protected by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

amperage ratings are listed on the product

rating plate.

WOLF WARMING DRAWER

Rating plate location

Location of

rating plate

Model ICBWWD30

with Stainless Steel

Drawer Front

Model ICBWWD30

with Integrated

Drawer Front

WOLF WARMING DRAWER

DRAWER FRONT OPTIONS

IMPORTANT NOTE:

Model ICBWWD30 must

be installed with a Wolf stainless steel or

integrated drawer front.

Classic Stainless Steel

WWDFRONT/S

Integrated Drawer Front

WWDFRONT/I

(accepts wood panel)

Drawer fronts are ordered and shipped as

sales accessories and include additional

installation instructions. Stainless steel drawer

fronts include a matching tubular handle.

The integrated drawer front accepts a custom

wood panel and handle to be provided by the

homeowner. Optional stainless steel tubular

handles in classic stainless steel are available

as sales accessories.

TOOLS AND MATERIALS REQUIRED

Wood screws or other hardware to install

the solid platform or runners that support

the warming drawer

51 mm x 51 mm or 51 mm x 102 mm

lumber for runners—runners must be able

to support 91 kg

51 mm x 51 mm or 51 mm x 102 mm

lumber for anti-tip block

Power saw

Level

Drill and 1,6 mm bit, 13 mm bit also for

integrated drawer front application

Phillips screwdriver

2 wood screws (provided)

Wood cleats for integrated drawer front

application

ACCESSORIES

Optional

accessories are

available through

your Wolf dealer.

BEFORE YOU START

Before you install the warming drawer,

make sure you have the Wolf accessory

drawer front called for in your installation.

IMPORTANT NOTE:

If you are installing

the warming drawer with integrated drawer

front in an inset panel application, make

sure that your cabinetry meets the

minimum 838 mm width and 635 mm depth

requirement for this installation.

Check with local utilities for electrical codes

that apply in your area. Local codes vary.

Installation, electrical connections and

grounding must comply with applicable

codes.

This appliance must be properly grounded.

Refer to Electrical Requirements on

page 14.

Make sure you have the tools and materials

necessary for proper installation.

INSTALLATION INSTRUCTIONS

MODEL ICBWWD30

with Stainless Steel Drawer Front

Overall Width 759 mm

Overall Height 260 mm

Overall Depth 689 mm

Depth Behind Frame* 597 mm

Minimum Cabinet Width 762 mm

Minimum Cabinet Depth 610 mm

Minimum Base Support 91 kg

Opening Width 727 mm

Opening Height 232 mm

Opening Depth 606 mm

*Allow 10 mm additional depth for cord thickness.

STAINLESS STEEL DRAWER FRONT

INSTALLATION SPECIFICATIONS

The following illustrations provide the overall

dimensions and installation specifications for

the Wolf warming drawer with a stainless steel

drawer front.

Wolf recommends using a 838 mm wide

cabinet for the warming drawer with stainless

steel drawer front. A minimum 762 mm wide

by 610 mm deep cabinet is required with a

minimum base support of 91 kg.

Refer to pages 16–17 for stainless steel drawer

front installation instructions. These instruc-

tions are also included with the stainless steel

drawer front kit.

UNDERCOUNTER INSTALLATION

For undercounter installations, 597 mm from

the bottom of the warming drawer opening to

the floor is recommended. It must be installed

a minimum of 127 mm above the floor or

25 mm above the toe kick.

The Wolf warming drawer with stainless steel

drawer front may be installed below an electric

or gas cooktop, provided the warming drawer

is fully enclosed, top and bottom. Allow

enough room for gas and electrical connec-

tions for the cooktop. Refer to installation

instructions for the cooktop for additional

specifications. Dimensions will vary according

to the specific installation.

Overall Dimensions – Stainless Steel Drawer Front

Undercounter Installation – Stainless Steel Drawer Front

WOLF WARMING DRAWER

STAINLESS STEEL DRAWER FRONT

INSTALLATION WITH BUILT-IN OVEN

The Wolf warming drawer with stainless steel

drawer front may be installed below or above

a Wolf 762 mm built-in single oven or below a

double oven, provided the warming drawer is

fully enclosed, top and bottom. Refer to the

illustration below. Also refer to installation

instructions provided with the built-in oven for

additional specifications. Dimensions will vary

according to the specific installation.

The Wolf warming drawer is designed and

agency approved for installation with Wolf

built-in ovens.

The warming drawer platform must be able to

support 91 kg. It must be a minimum of 25 mm

above the toe kick to allow for the overlap of

the warming drawer trim.

Installation with Built-In Oven – Stainless Steel Drawer Front

IMPORTANT NOTE:

Additional clearance

between warming drawer and oven openings

may be required. Check that oven supports do

not obstruct the interior dimensions required

for the warming drawer.

When the warming drawer is installed below

a built-in oven, a minimum of 60 mm between

warming drawer and oven openings is

required for placement of the anti-tip block. To

allow the warming drawer trim and the built-in

oven trim to meet, a 22 mm platform may be

used to separate the two openings. This will

act as the support platform for the oven and

the anti-tip device for the warming drawer.

Both applications are shown in the

illustration below.

IMPORTANT NOTE:

When the warming

drawer is installed above a built-in oven, a

22 mm platform is required to allow for

clearance of overlaps.

INSTALLATION INSTRUCTIONS

Installation with Built-In Oven and Microwave – Stainless Steel Drawer Front

OPTIONAL INSTALLATIONS

The Wolf warming drawer with stainless steel

drawer front may be installed in combination

with a 762 mm single oven and microwave

oven with 762 mm trim, provided the warming

drawer is fully enclosed, top and bottom. Refer

to the illustration below. Also refer to installa-

tion instructions provided with the built-in

oven and microwave for additional specifica-

tions. Dimensions will vary according to the

specific installation.

The warming drawer platform must be able to

support 91 kg. It must be a minimum of 25 mm

above the toe kick to allow for the overlap of

the warming drawer trim.

The Wolf warming drawer with stainless steel

drawer front may be installed next to or above

another Wolf warming drawer, provided each

unit is fully enclosed, top and bottom.

Installation with Built-In Oven – Stainless Steel

Drawer Front

STAINLESS STEEL DRAWER FRONT

WOLF WARMING DRAWER

MODEL ICBWWD30

with Integrated Drawer Front

Overall Width 746 mm

Overall Height 257 mm

Overall Depth* (behind frame) 597 mm

Minimum Cabinet Requirements

Overlay 838 mm W x 610 mm D

Inset 838 mm W x 635 mm D

Minimum Base Support 91 kg mm

Opening Width 749 mm

Opening Height 260 mm

Opening Depth** 610 mm

Minimum Panel Size

Overlay 762 mm W x 264 mm H

Inset 746 mm W x 257 mm H

Minimum Panel Thickness 16 mm

Maximum Panel Weight 11 kg

*Allow 10 mm additional depth for cord thickness.

**For the inset application, add the thickness of

the drawer face to the opening depth.

Overall Dimensions – Integrated Drawer Front

Integrated Drawer Front – Overlay Application

INTEGRATED DRAWER FRONT

INSTALLATION SPECIFICATIONS

The following illustrations provide the overall

dimensions and installation specifications for

the Wolf warming drawer with integrated

drawer front. The warming drawer with inte-

grated drawer front can be used in an overlay

application or an inset panel application where

it will be completely recessed in to the cabinet.

Keep in mind that the size of the custom panel

for the warming drawer with integrated drawer

front will vary according to the specific instal-

lation. The following chart provides minimum

dimensions for the overlay and inset panel

applications.

Refer to pages 18–20 for integrated drawer

front installation instructions. These instruc-

tions are also included with the integrated

drawer front kit.

Autres manuels pour ICBWWD30

Table des matières

Langues :

Autres manuels Wolf tiroir chauffant

Wolf

Wolf CW24/S Manuel utilisateur

Wolf

Wolf MWD24-2 Manuel utilisateur

Wolf

Wolf WWD30O Manuel utilisateur

Wolf

Wolf 13005870 Manuel de service

Wolf

Wolf 802727 Manuel utilisateur

Wolf

Wolf WWDFRONT/B Manuel utilisateur

Wolf

Wolf ICBWWD30 Manuel utilisateur

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf WWD30-2 Manuel utilisateur

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf ICBWWD30 Manuel utilisateur

Wolf

Wolf WARMING DRAWERS Manuel utilisateur

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf WWDFRONT/B Manuel utilisateur

Wolf

Wolf WD30 Manuel du propriétaire

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf WD30 Manuel utilisateur

Wolf

Wolf Warming Drawer Manuel utilisateur

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf WWD30 Manuel utilisateur

Wolf

Wolf Warming Drawer Manuel utilisateur

Wolf

Wolf ICBWWD30 Manuel du propriétaire

Wolf

Wolf WWD30 Instructions d'utilisation

Wolf

Wolf WWD30-2 Manuel utilisateur

Manuels tiroir chauffant populaires d'autres marques

Siemens

Siemens HW 290 Series Manuel utilisateur

Hatco

Hatco HDW-1 Instructions d'installation

APW Wyott

APW Wyott WD-2CMF Manuel utilisateur

Viking

Viking DEWD102SS Manuel utilisateur

Miele

Miele ESW 6229 Manuel utilisateur

Brandt

Brandt WD1014X Manuel utilisateur

KitchenAid

KitchenAid KOWT107ESS Manuel utilisateur

Gaggenau

Gaggenau WSP 222 Manuel utilisateur

DCS

DCS WDI Manuel utilisateur

Fisher & Paykel

Fisher & Paykel OR90SCG6R1 Manuel utilisateur

Electrolux

Electrolux EED21600X Manuel utilisateur

Fisher

Fisher PROFESSIONAL WB76SPEX1 Manuel utilisateur

Electrolux

Electrolux EW30WD55GS Manuel utilisateur

Hanseatic

Hanseatic TCN14J6D-S Manuel utilisateur

Jenn-Air

Jenn-Air JWD6030CDX Manuel utilisateur

Gaggenau

Gaggenau WS482710 Manuel utilisateur

Bosch

Bosch HWD2720UC Manuel utilisateur

NEFF

NEFF N29HA11Y2 Instructions d'utilisation et d'entretien