Wisenet SDC-99447BF Manuel utilisateur
SDC-99447BF
4K AHD Analog Bullet Camera
User Manual
Copyright
©2019
Hanwha Techwin
Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered
trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially
or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal
guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
Hanwha Techwin reserves the right to change the contents of this document without prior notice.
Design and specications are subject to change without prior notice.
4K AHD Analog Bullet Camera
User Manual
English _3
● OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
overview
4_ overview
overview
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within
this unit.
This exclamation point symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or
damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat
generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water
on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately
disconnect the power source and contact the service center. Continued use in such a condition may cause
fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this
product in any way. (Hanwha Techwin is not liable for problems caused by unauthorized modifications or
attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric
shock.
English _5
● OVERVIEW
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to
excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature, low temperature, or high humidity. Doing so may
cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall
it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause fire or
damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the
CMOS image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus
6_ overview
overview
CONTENTS
OVERVIEW
3
3Important Safety Instructions
4Safety Precautions
6Contents
7Product Features
INSTALLATION
8
8Part Names and Functions
9Precautions
9Installing the camera
10 Protection of Cable from Water
10 Connecting the DVR
APPENDIX
11
11 Product Specification
12 Product Overview
13 Troubleshooting
English _7
● OVERVIEW
PRODUCT FEATURES
• High resolution
Use the 4K-pixel CMOS, and provide high resolution equivalent to 1200TVL horizontal resolution.
• High sensitivity
The built-in high sensitive COLOR CMOS can produce a clear image. 0Lux (Auto IR LED On)
• D-WDR (Digit Wide Dynamic Range)
With the 4K-pixel CMOS sensor, this camera can provide a clear and quality image even under the
circumstance of backlight, by way of and accurate exposure for the dark area and reducing exposure for the
bright area: resulting in a clear, detailed and accurate image.
8_ installation
installation
PART NAMES AND FUNCTIONS
Name Description
aLens 4mm focal length enables you to monitor at a wider field of view
bIllumination Sensor Detects incoming light to control the IR LED.
cPower Cable Use to power the camera.
dBNC Cable BNC terminal for video signal output.
a
b
c
d
English _9
●INSTALLATION
PRECAUTIONS
Ensure you read out the following instructions before installing the camera:
•Select an area (ceiling or wall) that can withstand 5 times the camera weight
•Stuck-in or peeled-off cables can cause damage to the product or a fire.
•For safety purposes, keep anyone else away from the installation site.
And put aside personal belongings from the site, just in case.
INSTALLING THE CAMERA
The camera can be installed on the wall, ceiling, shelf or a desired position using the provided mounting bracket.
1. Choose an installation site that can sufficiently support the weight of the camera to be installed.
2. Adhere the installation template onto the ceiling and use it as installation locating tool.
3. Attach the camera mount to the wall using the supplied screws.
4. Adjust the direction of the camera to the desired direction, and tighten the bracket.
5. Adjust camera angle as needed.
6. Connect the camera cable to the camera.
Take caution when installing the camera outdoors because the cable connectors may be wet with
moisture or pile up with impurities.
Although the camera is IP66 rated, direct exposure to water or moisture may cause problem such as
condensation.
CAMERA FRONT
10_ installation
installation
PROTECTION OF CABLE FROM WATER
If this product is mounted outdoor, water leakage may occur at gap between cables. As shown below, butyl rubber
(available on the market) shall be used to protect from water.
1. Connect power supply and BNC power source.
2. Cover black sheath of the cable (Zone A), and ensure half of butyl rubber can cover the cable joint.
J `Poor water protection at the cable sheath may cause water leakage. Make sure to wrap tightly.
`The water-proof butyl rubber is made of rubber that expands to twice the original length.
`If you do not use cable joint, it must be covered with water-proof tape.
CONNECTING THE DVR
Connect the BNC connector of the camera to the enclosed 60ft camera cable, and then connect the BNC
connector of the camera cable to the BNC Video Input port of the DVR.
VIDEO INPUT
HDMI
VGA
LAN 12V
CAUTION
RISKOFELECTRI SHOCK
DONOTOPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK
DONOT OPEN COVERS. NO USER SERVICEABLE
PARTSINSIDE.REFER SERVICING TO QUALIFIED
SERVICEPERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD. DO NOT
EXPOSE UNITS NOT SPECIFICALLYDESIGNED
FOR OUTDOOR USE TO RAIN OR MOISTURE.
Table des matières
Autres manuels Wisenet Caméra de sécurité
Wisenet
Wisenet TNV-7011RC Manuel utilisateur
Wisenet
Wisenet XNO-8083R Manuel utilisateur
Wisenet
Wisenet XNV-8083R Manuel utilisateur
Wisenet
Wisenet XNF-9010RS Manuel utilisateur
Wisenet
Wisenet HCD-7010RA Manuel utilisateur
Wisenet
Wisenet SNO-6011R Manuel utilisateur
Wisenet
Wisenet SND-7084R Manuel utilisateur
Wisenet
Wisenet TNO-P9072EPT1-Z Manuel utilisateur
Wisenet
Wisenet ANO-L6082R Manuel utilisateur
Wisenet
Wisenet XNZ-L6320A Manuel utilisateur
Wisenet
Wisenet SNV-6013 Manuel utilisateur
Wisenet
Wisenet PNM-8082VT Manuel utilisateur
Wisenet
Wisenet HCD-6010 Manuel utilisateur
Wisenet
Wisenet PNM-C9022RV Manuel utilisateur
Wisenet
Wisenet TNO-6320E Manuel utilisateur
Wisenet
Wisenet PNM-9084QZ Manuel utilisateur
Wisenet
Wisenet PNM-9084QZ1 Manuel utilisateur
Wisenet
Wisenet TNV-8011C Manuel utilisateur
Wisenet
Wisenet TNU-4041T Manuel utilisateur
Wisenet
Wisenet HCO-7070R Manuel utilisateur
