Wireless Joey Dish Manuel utilisateur
01
Receivers | Wireless Joey
Wireless Joey
High/Standard Denition • Uses Wireless Joey Access Point
02
Installation Rules | Installing a Whole-Home System
Installing a Wireless Joey Receiver
Follow this procedure to install a Wireless Joey receiver. To ensure a proper installation,
see Maximum Components per Whole-Home System and the Wireless Joey diagrams in
the Installation Diagrams chapter.
Note: A Wireless Joey receiver uses its own wireless network that does not impact the
performance of an existing home network.
1. Check the mode switch:On the back panel of the Wireless Joey Access Point,
verify that the mode switch is set to Access Point, as shown below.
2. Connect the Wireless Joey Access Point:Connect an Ethernet cable from the
Wireless Joey Access Point to the desired Hopper receiver model or a
Hopper Internet Connector.
Note: Each Wireless Access Point supports up to three Wireless Joey receivers.
3. Power on the Wireless Joey Access Point:Plug in the Wireless Joey Access Point
to power to automatically power on the device. The blue Ethernet LED lights up,
then the green power light blinks, indicating that the Wireless Joey Access Point is
downloading software. Do not disconnect the device from power or Ethernet.
Wireless Joey
Wireless Joey Access Point
03
Installation Rules | Installation Rules and Guidelines
Maximum Components per Whole-Home System
Hopper and Hopper with Sling Receivers
•Two (2) Hopper receiver models when no Super Joey receiver is installed
•One (1) Hopper receiver model when a Super Joey receiver is installed. A Solo Node
is required; a Duo Node is prohibited.
Joey Receiver Models
•Three (3) Joey receivers per Hopper receiver model.
•A combination of four (4) Joey, Virtual Joey, and Wireless Joey receivers when no Super
Joey receiver is installed. A total of four Joey receiver models requires two Hopper
receiver models.
•A combination of three (3) Joey, Virtual Joey, and Wireless Joey receivers when a
Super Joey receiver is installed.
•One (1) Virtual Joey per Hopper receiver model.
Wireless Joey Receivers and Wireless Joey Access Points
•One (1) Wireless Joey Access Point per Hopper receiver model or
Hopper Internet Connector
•Three (3) Wireless Joey receivers per Wireless Joey Access Point
•Four (4) Wireless Joey receivers and two (2) Wireless Joey Access Points per
whole-home system
04
Installation Rules | Installing a Whole-Home System
4. Verify the connection to the receiver:At the TV connected to the desired host
Hopper receiver model, access the Whole-Home screen by pressing MENU on the
remote control and selecting Settings, Network Setup, then Whole-Home. Verify
that the Wireless Joey Access Point is detected as an attached device, as
shown below.
5. Connect the Wireless Joey receiver: At the TV where the customer wants the
Wireless Joey installed, connect the Wireless Joey receiver to the TV using an HDMI
(preferable) or RCA cable.
Warning: Do not cover the vents or stack anything on the Wireless Joey receiver.
Doing so can cause heat buildup and may damage the receiver.
6. Turn on the TV:Power on the TV and the Wireless Joey receiver. If necessary,
change the TV input to the source for the Wireless Joey receiver.
05
Installation Rules | Installing a Whole-Home System
7. Start the Setup Wizard for the Wireless Joey: When the Setup Wizard displays,
press SELECT on the front panel of the Wireless Joey to begin the connection
process to the Wireless Joey Access Point, as shown below.
8. Initiate Wi-Fi Protected Setup (WPS): Return to the Wireless Joey Access Point and
press WPSto connect the Wireless Joey receiver to the Wireless Joey Access Point
and the Hopper receiver model.
Note: WPS times out in two minutes. If you cannot connect the devices after several
attempts, the devices may be out of range with each other. Try moving one of the
devices closer and trying again. If there is another device that is also in WPS, stop
WPS on the device and try again.
06
Installation Rules | Installing a Whole-Home System
9. Complete the Setup Wizard: Complete all steps in the Setup Wizard, which will
guide you in positioning the Wireless Joey and Wireless Joey Access Point to
produce an optimal signal.
Note: Performance may vary depending on environmental factors, such as building
materials and objects that interfere with the video signal.
10. For each additional Wireless Joey receiver: Repeat the necessary steps in this
procedure. A whole-home system supports three Wireless Joey receivers (using
one Wireless Joey Access Point) or four Wireless Joeys (using two Wireless Joey
Access Points). See Maximum Components per Whole-Home System for compatible
congurationsfortheinstallation.
07
Devices and Accessories | Wireless Joey Access Point
Wireless Joey Access Point
•Servesasavideo-grade802.11acwirelessaccesspoint
between one Hopper receiver model and up to three
Wireless Joey receivers.
•Creates its own wireless network that does not impact
the performance of a home network.
•Serves video and data wirelessly to a Wireless Joey.
The Wireless Joey Access Point connects via Ethernet
cable to a Hopper receiver model or Hopper Internet
Connector. Do not connect a Wireless Joey Access Point
directly to a home-network router.
•The Wireless Joey Access Point and the Wireless Joey
are intended to sit upright to ensure optimal signal
strength. Do not mount these devices or lay them on
their sides.
08
Installation Diagrams | Wireless Joey: 4-TV Installation
Wireless Joey: 4-TV Installation
2 Wireless Joeys, 1 Wireless Joey Access Point, 1 Hopper with Sling, 1 Joey
ROOM 3ROOM 4 ROOM 2 ROOM 1
Joey
Wireless
Joey
Access
Point Hopper with Sling
Wireless Joey
Wireless Joey
Solo Node
Satellite
950–2150 MHz
MoCA
650–875 MHz
Satellite
and
MoCA
650–3000 MHz
Cables
HDMI
Ethernet
Router
(Bridging Enabled)
09
Installation Diagrams | Wireless Joey: 6-TV Installation
Wireless Joey: 6-TV Installation
4 Wireless Joeys, 2 Wireless Joey Access Points, 2 Hopper with Slings, 1 Joey
ROOM 1 ROOM 2 ROOM 3 ROOM 4 ROOM 5 ROOM 6
(Bridging Enabled)
Wireless Joey
Access Point
Wireless Joey
Access Point
Duo Node
Hopper with Sling
H.I.C.
Satellite
950–2150 MHz
MoCA
650–875 MHz
Satellite and MoCA
650–3000 MHz
Cables
HDMI
Ethernet
Wireless
Router
MMTTVV-FMYYXXXXX
TOCLIENT TO CLIENT
EchoStarTechnologies L.L.C.
Groundingwire size: Copper wire-8-14 AWG
Coppercoated steel wire-17 AWG
T
O
L
N
B
F
S
DUO NODE
185836
TOHOST
10.5-28V
TOHOST
10.5-28V
pp g
Hopper with Sling
pp g
Wireless Joey
Wireless Joey
Wireless Joey
Wireless Joey
Terminator
10
Installation Diagrams | Super Joey and Wireless Joey: 5-TV Installation
Super Joey and Wireless Joey: 5-TV Installation
1 Super Joey, 1 Wireless Joey, 1 Wireless Joey Access Point, 1 Hopper with Sling, 2 Joeys
ROOM 1 ROOM 2 ROOM 3 ROOM 5ROOM 4
Satellite
950–2150 MHz
MoCA
650–875 MHz
Satellite and MoCA
650 ≤ 3000 MHz
Cables
HDMI
Ethernet Integrator
Joey
Joey
Solo Node
Super Joey
Wireless
Router
Hopper with Sling
(Bridging Enabled)
Wireless Joey
Wireless Joey
Access Point
3-Way
Splitter
Table des matières
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
