Winson WNI-6712 Manuel utilisateur
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
1/29
Winson wireless barcode scanner user manual
Launch date：2019-5-29
1、Ver：V3.8
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
2/29
Revision record
2019/5/29 Rev 3.8
1. Remove the settings that do not match the code.
2. The version specification is revised based on Src-0085 V3.4 and Src-0083 V3.4.
2018/11/30
1. Classification character output setting code
2017/8/9 Rev 3.3
1. Add wireless channel setting code
20017/9/14 rev 3.4
1. Modify the input and output character format setting code
20170915 Rev 3.5
1. Increase keyboard case detection settings
2. Increase the small keyboard switch settings
20170125 Rev3.6
1. Increase proximity matching
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
3/29
1 . Comprehensive settings
1.1 Setting instruction description
1. The setting bar code is uniformly printed with Code128 type CODE B set bar code.
2. An asterisk (*) in the description part indicates the factory default parameters.（1）Scan: Enter setting
mode “@SET”. After enter setting, it will exit the setting mode if next setting command is not scan
within 20s.
（2）Scan: the relevant setting barcode. In this step, you can scan one or more setting barcode
commands.
（3）Scan: Exit and save “@END”.
（4）The setting of some functions can directly scan the corresponding quick setting bar code. Such as:
pairing barcode, unpairing barcode, etc.
3.2 Set command data format
Table 3.3-1 Setting command data format table①
Prefix
Setting goals
Type
Parameter
WN-
T-/R-/W-
Refer to "Set Barcode Type
Table"
*****
Notice ①This format does not include instructions for entering settings and saving and exiting settings.
Table 3.3-2 Set instruction data format analysis
Format
Data
Description
Prefix
WN-
Fix prefix symbol
Setting goals
T-/R-/W-
T-:Means to set the barcode directly to the sender end.
R-:Means to set the barcode directly to the receiver end,
and the setting bar code of the receiving end
needs to be forwarded by the sending end
through wireless transmission.
W-:The sender end and receiver end work at the same
time
Type
Refer to "Set Barcode Type Table"
Parameter
The parameter is 4 characters in the range of "0~9"
3.4 Set barcode type table
Table 3.4-1 Set barcode type table
Type
Description
A
Wireless pairing/unpairing
B
Multi-language settings
C
View firmware information/Modify frequency
D
Infrared sensor trigger switch
F
Real-time mode / inventory mode / inventory mode data operation
G
Sleep time
H
Restore default setting
I
Data transmission form, start symbol mode setting, custom start
symbol
K
Sending/receiving end firmware upgrade command
L
USB wired output switch
3.5 “Enter setting” and “Save and exit”
Command：
Function
Command
barcode
Remark
Enter setting
@SET
Enter the setting prompt sound,
effective time of 20 seconds
Save and
exit
@END
Save and exit settings prompt sound
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
4/29
Note☆: 1. For the setting of non-quick setting commands, it must first scan to enter the setting command,
then scan the corresponding parameter setting command, and finally scan to save and exit the
setting command.
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
5/29
4. Setting barcode type
4.1 Pairing command★
Function
Command
barcode
Remark
Start
pairing
@.WN-T-A0001/
Can be paired
remotely
Close
pairing
@.WN-T-A0002/
Only allow pairing
Note☆: 1. The effective time of pairing is within 20S from the moment the receiver is powered on (the
LED is flashing). After 20s, the LED is always on and cannot be paired. (This method is for
the receiver without buttons)
2. Press the receiver button, the receiver will automatically enter the pairing state, during this
period it can be paired normally. (This method is for the receiver with buttons).
3. 2.4G stops flashing after pairing successfully.
4.2 HID-KEYBOARD multi langue setting★
Function
Command
barcode
Remark
@SET
*USA
WN-W-B1000
FRENCH
WN-W-B1001
GEMRAN
WN-W-B1002
TUKISH
WN-W-B1003
BELGIUM
WN-W-B1004
BRAZIL
WN-W-B1005
CRZCH
WN-W-B1006
SPANISH
WN-W-B1007
Latin America
@END
Note★: This setting code is valid for both the receiving end (Tx) and the sending end (Rx). If
multiple languages are set when the wireless transmission connection is disconnected, the sending
end language setting will be successful, but the receiving end language will not change.
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
6/29
4.4 Check parameter
Function
Command
barcode
Remark
Output parameter of
system
WN-W-
C1000
1> Firmware version
2> Battery level
3> Wireless channel
Explanation ☆: The command to view the parameters is sent to the receiver along with the system
parameters, and each parameter is separated by a terminator, such as:
PKT{protocol field|WN-W-B1001|parameter 1+0x0D|parameter 2+0x0D |……} (the content of the data
packet in {})
4.5 Operation mode★
Function
Command
barcode
Remark
*Real-time
mode
@.WN-T-
F0000/
Scan and transfer, fail alarm
Cache
mode
@.WN-T-
F1000/
On the basis of real-time mode,
increase the buffer data after
transmission failure. The system
will automatically upload the
cached data after detecting that the
device has not been operated for
three seconds. If the cached data is
not uploaded when the machine is
turned off, the system will continue
to detect the upload after the next
startup until the transmission is
completed.
Inventory
mode
@.WN-T-
F2000/
The barcode data is automatically
stored, and it is uploaded once after
scanning "Upload Data"; scanning
"Clear Data" to clear the data in the
memory "Scan "Data Total" to
view the total number of data in the
memory
After scanning the barcode, the
data is directly stored in the
barcode scanner, and the data will
not be deleted until the [Clear
Data] is scanned. During this
period, you can scan [upload data]
to send the data to the receiver or
directly upload to the PC
Upload data
@.WN-T-
F2001/
Upload barcode data
Data sum
@.WN-T-
F2002/
Upload the sum of barcode
Clear data
@.WN-T-
F2003/
Clear the barcode data in the
inventory mode
Notice☆:1. Six command in operation mode are all quick setting command, the setting is successful
when scan them successful.
2. Upload data, data amount, clear data in inventory mode, these three operation setting
command is unavailable when enter setting mode, if it is already in setting mode, must save
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
7/29
and setting before using these three operation setting command.
3. New 433 and 2.4G solution (model number：WNI-xxx2, WNI-xxx3,WNC-xxx2,WNC-xxx3)
storage data description:
Inventory mode: storage length is 30 Byte data will be able to store 49,000pcs
storage length is 13Byte data will be able to store 104,500pcs
Cache mode:storage length is 30 Byte data will be able to store 14,200pcs
storage length is 13Byte data will be able to store 30,300pcs
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
8/29
4.6 Character input/output/keyboard format setting
4.6.1 Case control and keypad switch
Function
Command
barcode
Description
*Uppercase key
(CapsLK) detect
on
@.WN-W-
F3201/
Turn on uppercase detection,
keyboard Caps will not affect the
output
example: barcode
content:123ABCdef
Turn on Caps output:
123ABCdef
Turn off Caps output:123ABCdef
Uppercase
key(CapsLK)
detect off
@.WN-W-
F3202/
After turn off the caps detection,
the keyboard Caps lock will
affect the output
example: barcode
content :123ABCdef
Turn on Caps output:123abcDEF
Turn off Caps output:123ABCdef
Turn on Numeric
keyboard
@.WN-W-
F3203/
After turn on, it need to set the
output to GBK format. If the
language is German at this time,
it needs to be set to English, and
other languages do not need to be
set.
4.6.2 Out put format and function key setting
Function
Command
barcode
Test instruction
*GBK
output
@.WN-W-
F3001/
1.Support txt and Excel output
2.Use WDI2000 module, set to
GBK output
3.Open txt or Excel, scan the code
to transmit data normally
Unicode
output
@.WN-W-
F3002/
1.Support Word output;
2.Use WDI2000 module, set to
UTF-8 output
Function
key
output
@.WN-W-
F3005/
1.Support testing in Excel file;
2.Add function key suffix:
For example: set the "→"
function key as a suffix, after
outputting data in Excel, the
cursor will point to the right cell
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
9/29
4.7 Sleep times setting★
Function
Command
barcode
Remark
@SET
1 min
WN-T-G0001
*5min
WN-T-G0005
15min
WN-T-G0015
45min
WN-T-G0045
non-sleep
WN-T-G0000
@END
Instructions☆: The calculation method of sleep time：60 * x = n (s) , X is two decimal values after the
barcode
4.8 Restore the factory settings★
Function
Command
barcode
Remark
@SET
Factory
Default setting
WN-W-H0000
1> autoSetFactory
remains unchanged
2> The current
spectrum constant
3> Matching the
address remains the
same
4> The wireless channel
is constant
5> Locking band logo
remains the same
6> Data output way
remains the same
7> The keyboard
language remains the
same
8> Buzzer sound
remains the same
@END
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
10 /29
4.9 0x0A filter
Turning on will filter out the 0x0A (newline character) in the middle of the string, and the 0x0A at the end of the
string (the first and second to last) will not be filtered.
Function
Command
barcode
Remark
*Turn on 0x0A
filter
@.WN-W-
F3301/
After turn on, the
newline character
0x0A in the middle
of the string will be
filtered.
Turn off 0x0A
filter
@.WN-W-
F3302/
If there is a newline
character in the data
after closing, it will
be output normally
Autres manuels Winson Lecteur de codes-barres
Manuels Lecteur de codes-barres populaires d'autres marques
POSMicro
POSMicro Datalogic PowerScan D7100 Manuel utilisateur
Marson
Marson MT780 Guide de configuration rapide
NCR
NCR RealPOS Manuel utilisateur
Motorola
Motorola SE3300 Guide de configuration rapide
Element
Element P130BT Manuel utilisateur
Motorola
Motorola Symbol LS3008 Manuel d'installation et d'exploitation
