Winland Electronics EnviroAlert EA800-IP Instructions d'installation

D-011-0152

Electronic Multi-Zone Environmental Alarm System

Installation/Owner’s Manual

Limitations of the Alarm System or Device

While your alarm system or device is reliable and sophisticated, it does not offer guaranteed protection against

burglary, fire or other emergency. Any security product, whether commercial or residential, is subject to

compromise or failure-to-warn for a variety of reasons. These include:

•Individuals may gain access through unprotected openings or have the technical sophistication to

bypass an alarm sensor or disconnect an alarm warning device.

•Monitoring devices will not operate without power. Devices powered by AC will not work if their AC

power supply is off for any reason. If system has battery backup, batteries that are not maintained can

fail to provide the necessary power for devices to function properly.

•Alarm warning devices such as sirens, bells, and horns may not alert people or awaken sleepers if they

are located on the other side of closed or partly closed doors. If warning devices are on a different level

of the residence from the bedrooms, they are less likely to awaken or alert people inside the bedrooms.

•Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may

be out of service, and are subject to compromise by sophisticated means of attack.

•Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm

receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if

a metal object is moved into the path.

•Even if the system responds to the emergency as intended and is a monitored alarm system, the

authorities may not respond appropriately.

•This equipment, like other electrical devices, is subject to component failure.

•The most common cause of an alarm system not functioning properly is due to inadequate

maintenance. Your alarm system should be tested weekly to make sure all detection devices are

operating properly. Your control panel and keypads should be tested as well.

Installing an alarm system may make you eligible for lower insurance rates, but an alarm system is not a substitute

for insurance. Homeowners, property owners, and renters should continue to insure their lives and property.

D-011-0152 3

Table of Contents

General Information............................................................................................................................... 5

Overview............................................................................................................................................ 5

How to Use This Manual.................................................................................................................... 6

Block Diagrams.................................................................................................................................. 7

Symbols on the Product or Manual Labeling ..................................................................................... 8

Monitoring Screens............................................................................................................................ 9

Keys................................................................................................................................................. 10

Console Connections....................................................................................................................... 11

Access Control and Passwords ....................................................................................................... 13

System Configuration Parameters................................................................................................... 13

Sensors............................................................................................................................................ 15

Temperature Sensors ................................................................................................................ 15

Humidity Sensors....................................................................................................................... 16

4-20mA Sensors ........................................................................................................................ 16

Theory of Operation ....................................................................................................... 16

Power Supply / Sensor Voltage Selection...................................................................... 17

Water Sensors ........................................................................................................................... 18

Multi-Function Sensors .............................................................................................................. 18

Dry Contact Sensors.................................................................................................................. 18

Sensor Parameter Descriptions ................................................................................................. 19

Relay Operation............................................................................................................................... 21

Installation............................................................................................................................................ 22

Tools and Supplies Required........................................................................................................... 22

Power Requirements ....................................................................................................................... 22

Mounting the EA800-ip Rear Plate ...................................................................................................... 22

Install the Wired Sensors................................................................................................................. 23

EA800-ip Console Power Connections................................................................................................ 23

Install the Wireless Sensors............................................................................................................. 23

Connecting Wired Sensors .............................................................................................................. 25

Programming ................................................................................................................................... 27

Accessing the MAIN MENU for Programming ........................................................................... 28

Configuring System Parameter Settings.................................................................................... 28

Adding Wireless Sensors................................................................................................................. 29

Verify Wireless Signal Strength ................................................................................................. 31

Adding Wired Sensors ..................................................................................................................... 32

Adding a Wired Sensor .............................................................................................................. 32

Adding a 4-20mA Sensor........................................................................................................... 33

Configuring the Relays..................................................................................................................... 34

Operation.............................................................................................................................................. 35

Monitoring Environmental Conditions .............................................................................................. 35

Viewing Sensor Settings.................................................................................................................. 36

Viewing Active Alarms ..................................................................................................................... 36

Viewing the Alarm Log..................................................................................................................... 37

Viewing the Event Log ..................................................................................................................... 38

Viewing the Sensor Log................................................................................................................... 39

Viewing Firmware Information ......................................................................................................... 39

Viewing RF Information.................................................................................................................... 40

4D-011-0152

Maintenance ......................................................................................................................................... 41

Locking and Unlocking the EA800-ip ................................................................................................... 41

Pausing Monitoring and Cancelling Pause ...................................................................................... 42

Replacing a Sensor.......................................................................................................................... 43

Editing Sensor Parameters .............................................................................................................. 44

Deleting a Sensor ............................................................................................................................ 45

Changing the Date Format............................................................................................................... 45

Changing the Time Format .............................................................................................................. 46

Changing the Date or Time Setting.................................................................................................. 46

Changing Sensor Data Collection Frequency.................................................................................. 46

Changing the Buzzer Setting ........................................................................................................... 47

Changing the Password................................................................................................................... 48

Clearing the Alarm Log .................................................................................................................... 49

Clearing the Sensor Log .................................................................................................................. 49

Updating the Firmware..................................................................................................................... 50

Saving Configuration Settings.......................................................................................................... 51

Loading Configuration Settings........................................................................................................ 52

Exporting the Stored Logs ............................................................................................................... 53

Exported Alarm Data.................................................................................................................. 53

Exported Event Data.................................................................................................................. 54

Exported Sensor Data................................................................................................................ 54

Troubleshooting................................................................................................................................... 55

Verifying RF Signal Strength............................................................................................................ 56

Viewing Signal Strength for a Wireless Sensor.......................................................................... 56

Specifications....................................................................................................................................... 57

Console and Sensor Specifications ................................................................................................. 57

Accessories...................................................................................................................................... 58

Warranty and Service Information ..................................................................................................... 61

D-011-0152 5

General Information

Overview

The EnviroAlert® EA800-ip Multi-Zone Environmental Alarm System monitors the environmental conditions detected

by the sensors connected to the console, and provides alarm signals when monitored conditions at any of the

sensors exceed the user-programmable HIGH LIMIT orLOW LIMIT set points. The alarm signals are provided via

relay outputs that can operate with process controls, security systems, or other similar automated equipment. The

EA800-ip Alarm System can be configured with wired or optional wireless sensors (sold separately).

The EA800-ip allows connection of up to 4wired and up to 8 wireless sensors.

Setup and programming is done using the front panel keys and the liquid crystal display (LCD) on the console.The

display assists the user during setup, and shows measured conditions for the monitored environment during

operation.

The EA800-ip can monitor multiple critical environments using multiple sensor inputs. Each sensor input has a

corresponding relay output.

Using the appropriate accessory sensors (sold separately), the EA800-ip Alarm System monitors and provides

alarms for the following conditions:

■Temperature: from -80° C to 150° C (-112° F to 302° F)

■Humidity: from 5 to 95% RH (non-condensing)

■Presence of water

■Any sensor with a 4-20mA interface

The EA800-ip console may be mounted directly to a standard 3-gang electrical enclosure or to walls. The wireless

sensors are easily mounted to the wall. Figure 1 shows the console and a wireless sensor.

Figure 1 EnviroAlert EA800 Console and Optional Wireless Sensor

6D-011-0152

How to Use This Manual

This manual is organized into sections that guide you through the installation process, then describe how to use

the EA800-ip and change its programmed settings if necessary. Some troubleshooting guidelines are provided.

The manual presents EA800-ip programming procedures by showing you the sequence of menus and screens you

will see as you perform the procedure, and the keys to press to advance to the next screen. The example below is

the procedure for unlocking the EA800-ip console to allow programming.

The arrows on the drawing indicate the direction of procedure flow.

In all procedures, use the keys to select menu options and to increase/decrease alphanumeric values for

programming options. Use the PREV and NEXT soft keys (F2 and F3) to move the cursor to the next digit when

entering numeric data.

The functions of the soft keys change and are defined on the screen in the area above each key. If no

text is shown above a soft key, it means the key performs no function on the current screen.

“Keys” on page 10 describes the functions of each key on the console.

Throughout the manual, text that appears on the EA800-ip console screens is shown like this: MONITORING

Key names are shown in text like this: F1

The current menu selection is highlighted on the screen by arrows on either side of

the selection, as shown in the example at right. On this MAIN MENU screen, the

current selection is Sensors.

Use the or keys to move the highlight to the desired menu item, then

press to make the selection.

Enter:

0800

Step 1: Press the

F1 soft key.

Step 2: The UNLOCK screen

is displayed. Enter your

password using the arrow

keys.

Step 3: Press the

ENTER key

F1 can be pressed at this time

to lock the unit.

F1 F2 F3

General Information

D-011-0152 7

Block Diagrams

Figure 2 shows a block diagram of the console interfaces and functions. The EA800-ip provides eight relays for

indicating when a programmed alarm limit has been exceeded or a warning condition exists. An additional AUX

(Auxiliary) Output relay provides an output signal to an optional audible alarm or strobe that is activated whenever

an alarm condition exists.

Figure 2 EA800 Environmental Alarm System Block Diagram

The EA800 can be made part of a larger security system as shown in Figure 3. In a security system there may be

more than one EA800 installed along with other components such as the Winland EA200 or EA400 multi-zone

environmental alarm systems.

Figure 3 Facility Security System Block Diagram - Example

Sensor 5

Sensor 6

Sensor 7

Sensor 8

Wireless Sensors

Relay 1 Output 1

Output 2

Relay 2

Output 3

Relay 3

Output 4

Relay 4

Output 5

Relay 5

Output 6

Relay 6

Output 7

Relay 7

Output 8

Relay 8

EA800 Console

Aux Output

RF Receiver

Sensor 1

Sensor 2

Sensor 3

Sensor 4

System Control

Relay 9

Relay 1 coil control logic

Relay 2 coil control logic

Relay 3 coil control logic

Relay 4 coil control logic

Relay assignment

and coil control logic

Wired Sensors

Alarm Panel

From other

EA800, EA400, and EA200

Environmental Alarm Systems

Sensor 5

Sensor 6

Sensor 7

Sensor 8

Wireless Sensors

Relay 1 Output 1

Output 2

Relay 2

Output 3

Relay 3

Output 4

Relay 4

Output 5

Relay 5

Output 6

Relay 6

Output 7

Relay 7

Output 8

Relay 8

EA800 Console

Aux Output

RF Receiver

Sensor 1

Sensor 2

Sensor 3

Sensor 4

System Control

Relay 9

Relay 1 coil control logic

Relay 2 coil control logic

Relay 3 coil control logic

Relay 4 coil control logic

Relay assignment

and coil control logic

Sensor 5

Sensor 6

Sensor 7

Sensor 8

Wireless Sensors

Relay 1 Output 1

Output 2

Relay 2

Output 3

Relay 3

Output 4

Relay 4

Output 5

Relay 5

Output 6

Relay 6

Output 7

Relay 7

Output 8

Relay 8

EA800 Console

Aux Output

RF Receiver

Sensor 1

Sensor 2

Sensor 3

Sensor 4

System Control

Relay 9

Relay 1 coil control logic

Relay 2 coil control logic

Relay 3 coil control logic

Relay 4 coil control logic

Relay assignment

and coil control logic

Wired Sensors

8D-011-0152

Symbols on the Product or Manual Labeling

Symbols appearing on the product labeling, packaging, and/or in this manual are shown and described in Table 1.

Table 1 Symbols on Product or Manual

Symbol Definition

Attention, consult accompanying documents or statements.

For product disposal, ensure the following:

• Do not dispose of this product as unsorted municipal waste.

• Collect this product separately.

• Use collection and return systems available to you.

Indicates product complies with RoHS-WEEE directive.

N.O. Normally Open (N.O.) relay contact terminal

N.C. Normally Closed (N.C.) relay contact terminal

CCommon relay contact terminal

AUX Combined single pole double throw (SPDT) relay output that activates upon an alarm

from any of the sensors.

Model: EA800-ip

• FCC ID:

V5SEA800-031108

• IC: 7635A-EA800

Models: EA-WMFS,

EA-WTS, EA-WHS

• FCC ID:

V5SEA-WS-031108

• IC: 7635A-EAWS

This device complies with part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Caution Statement (per CFR 15.21):

Changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

Class B Product Compliance Statement (per CFR 15.105(b)):

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction, may cause harmful

interference to radio communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The TÜV certification combines electrical safety certification for Canada (SCC), United

States (NRTL), and Europe (EU Directives). This product was voluntarily tested

according to the relevant safety requirements and mentioned properties pertaining to

this certification mark.

The product is in conformity with all applicable requirements for its placing on the

European Union market.

General Information

D-011-0152 9

Monitoring Screens

The EA800-ip user interface is menu-based. During normal system monitoring, one of the following three screens is

displayed depending on the current state of the programmed sensors:

The MONITORING (home) screen is displayed

when there are no active alarms. The screen lists

all programmed sensors connected to the console

and their current reading or state.

The MONITORING screen displays pending alarms

in inverse as shown in the example at right

(76% exceeds the humidity limit for Sensor 5, so it

is shown as light text on black). Pending alarms

indicate that the programmed limits for the sensor

have been exceeded, but the sensor’s pro-

grammed delay time has not yet elapsed. If the

monitored conditions continue to exceed the pro-

grammed limits for longer than the programmed

delay period, the pending alarm will become an

active alarm.

The ACTIVE ALARMS screen is shown when one or

more sensors are in an active alarm or warning

state. If more than one alarm is active, each will

be listed on the screen. In the example shown, a

Cooler #1 alarm is occurring.

10 D-011-0152

Keys

Figure 4 shows the console display and entry keys. The keys are described in Table 2.

Figure 4EA800-ip Console Keys

Table 2 Key Functions

Key Function

F1 This key's function changes as determined by the software. Its current function is

displayed immediately above the key on the display.

F2 This key's function changes as determined by the software. Its current function is

displayed immediately above the key on the display.

F3 This key's function changes as determined by the software. Its current function is

displayed immediately above the key on the display.

Up Arrow: This key provides the scroll up function. It moves the selection cursor up

a list or increments the value of alphanumeric entry fields as identified by the flash-

ing cursor. The values provided are dependent on the currently active field. For

example, the available selections may be a + or - sign, numbers, or alphanumeric

characters and special characters.

Down Arrow: This key provides the scroll down function. It moves the selection

cursor down a list or decrements the value of alphanumeric entry fields as identified

by the flashing cursor. The values provided are dependent on the currently active

field. For example, the available selections may be a + or - sign, numbers, or alpha-

numeric characters and special characters.

ENTER key. This key accepts the currently entered selection when pressed. If the

selection is a menu item, the selected item is accessed. If the current selection is an

entered value, pressing the ENTER key accepts the entered value.

HOME key. This key displays the home screen (MONITORING) when pressed.

Autres manuels pour EnviroAlert EA800-IP

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Winland Electronics Système de sécurité

Winland Electronics

Winland Electronics EnviroAlert EA800-IP Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur