Winext AN-304 Manuel utilisateur
AN-304 PIR Motion Sensor User Manual
0
AN-304 PIR Motion Sensor User Manual
1
Table of contents
1. Introduction...................................................................................................................................2
1.1 Description..........................................................................................................................2
1.2 Features ...............................................................................................................................2
1.3 Specification........................................................................................................................3
2. Structure....................................................................................................................................4
2.1 Appearance and dimension .................................................................................................4
2.2 Packing contents .................................................................................................................4
3. Operation.......................................................................................................................................5
4. Configuration ............................................................................................................................6
4.1 Precaution............................................................................................................................6
4.2 Tool list ...............................................................................................................................6
4.3 Wireless configuration ........................................................................................................7
4.3.1 Wireless configuration tool ......................................................................................7
4.3.2 Install CP210x driver for wireless configuration tool ..............................................7
4.3.3 Parameter setting....................................................................................................10
5. Installation...................................................................................................................................13
5.1 Safety precaution...............................................................................................................13
5.2 Tools..................................................................................................................................13
5.3 Quick installation ..............................................................................................................14
5.4 Pictures after installation...................................................................................................14
6. Communication Format ..............................................................................................................15
AN-304 PIR Motion Sensor User Manual
2
1. Introduction
1.1 Description
AN-304 is a wireless infrared detector that can automatically detect the movement of
human body in the area. When an intruder passes through the monitoring area and
moves dynamically, an alarm signal will be sent to the monitoring platform
immediately. It is suitable for the safety prevention of residential area, villas,
workshops, shopping malls, warehouses, office buildings and other places.
1.2 Features
Support LoRaWANTM class A
Support wireless remote real-time monitoring
Ceiling-mounted or wall-mounted installation
Detecting distance 8-10m
Support anti-dismantle alarm
Support low power warning
Support status report
Working temperature: -10°C～55°C
AN-304 PIR Motion Sensor User Manual
3
1.3 Specification
Function
Item
Description
Wireless
performance
Antenna
Built-in LoRa Antenna
Data transmission rate
300bps-5.4Kbps
Frequency
CN470-510MHz
EU863-870MHz
US902-928MHz
AS923MHz
AU915-928MHz
KR920-923MHz
Maximum Tx power
19dBm
Rx sensitivity
-140dBm(SF=12)
Detecting function
Detecting range
8-10m
Detecting angle
100 degree
Working Ambient
Working temperature
-10℃- +50℃
Working humidity
5%-95% (no condensing)
Electric parameter
Power supply
Built-in Li-SOCL2
Standby electric
current
≤15uA
Tx current
≤120mA
Physical parameter
Dimension
86mm*86mm*26mm
AN-304 PIR Motion Sensor User Manual
4
2. Structure
2.1 Appearance and dimension
Figure: AN-304
Figure: AN-304 Dimension(mm)
2.2 Packing contents
Accessory
Qty(pc)
Remark
AN-304 PIR Motion Sensor
1
/
Installation board
1
/
Screw
4
2pcs long plastic plug
& 2pcs short screw
3M double-side tape
1
/
User manual
1
/
AN-304 PIR Motion Sensor User Manual
5
3. Operation
Turn on: Press and hold the Turn on/off button on the back of the device for
about 2 seconds. Release the button as the green light on.
Join network: After starting up, the LED enters a 60-second slow flashing state
and the red light flashes slowly, indicating that the device doesn’t join the
network successfully and when the light changes from red to green, indicating
that the device joins network successfully.
Note: After the device is switched on, the LED indicator will only have a
60-second slow flashing state, this state will be cancelled after 60 seconds
regardless of whether the device has successfully joined the network or not.
Auto-detecting mode: After starting up, it will enter into auto-detecting mode
within the first 5 minutes. If it detects a motion within the detecting area, the
device will send out a detection signal and the red light will flash.
Working mode: After starting up and 5 minutes later, it will enter into normal
working mode. There is a 5-minute interval between 2 alarm signals detected.
After 5 minutes, if it detects motion, the device will send out alarm signals again.
Dismantle alarm: In normal working mode, when the device dismantled, it will
send out illegal disassembly signal with the red light flashing.
Heartbeat: The device will send heartbeat signals to the cloud platform every 8
hours to report its working status.
Turn off: Long press the Turn on/off button on the back of the device for 1.5s,
LED light will turn green and then red, and then releasing the button, the device
will be turned off and stop working.
AN-304 PIR Motion Sensor User Manual
6
4. Configuration
4.1 Precaution
For device normal operation and detection accuracy, please pay attention to the
following matters before configuration:
Before configuration, please contact our technical staff for the relevant
software and manual.
For wireless configuration, it should be done within the signal coverage area
of the wireless configuration tool
4.2 Tool list
Note: For configuration, you can use wireless configuration tool (wireless
configuration) or USB to TTL cable (cable configuration), but here we choose to tell
customer how to do wireless configuration.
Item
Description
Laptop
Installation
Wireless Configuration tool
The laptop communicates with device via
wireless configuration tool ireless
configuration tool(wireless configuration),
you should install CP210x driver for this
tool
Configuration software
Winext manage App
AN-304 PIR Motion Sensor User Manual
7
4.3 Wireless configuration
4.3.1 Wireless configuration tool
Configuration tools as below:
a) Install the CP210x driver for wireless configuration tool, file as below:
b) Install Winext manage App, file as below:
4.3.2 Install CP210x driver for wireless configuration tool
(1) Open CP210x driver for wireless configuration tool
(2) Select the driver program to install depending to the system type.
32-bit operating system selects “CP210xVCPInstaller_x86.exe”.
64-bit operating system selects "cp210xvcpinstaller_x64.exe".
AN-304 PIR Motion Sensor User Manual
8
(3) Install Wireless configuration tool driver
Here we take an example to use the 64-bit operating system to install the wireless
configuration tool driver
Click and select Next to the driver file "cp210xvcpinstaller_x64.exe".
As below:
Select Accept the License Agreement and click on Next, as below:
AN-304 PIR Motion Sensor User Manual
9
Wait for a while and click on Finish, as below:
Check the driver program after installation finished. Click on Computer-Attribute-
Device manager, as below:
Table des matières
