Wiedamark LSD-18.25 Manuel utilisateur
LED ViDEo Curtain
User ManUal
Table&of&contents&
1.#INTRODUCTION#..........................................................................................................................................#3#
1.1&Underlying&information&and&preparation...................................................................................................&3&
2.#SAFETY#INSTRUCTIONS#............................................................................................................................#4#
3.#OPERATING#DETERMINATIONS................................................................................................................#5#
4.#COMPONENTS#OF#A#DISPLAY...................................................................................................................#6#
4.1&Mounting&elements&and&connections&of&a&display&....................................................................................&6&
4.2&All>in>one&network&control&system&LED&Show&T9.....................................................................................&7&
4.3&Network&control&system&LED&Studio&......................................................................................................&11&
5.#MOUNTING#................................................................................................................................................#12#
5.1&Safety&instructions.................................................................................................................................&12&
5.2&Allowed&number&of&units&connected&on&one&suspension&point...............................................................&12&
5.3&Mounting&steps......................................................................................................................................&13&
6.#CONNECTIONS#.........................................................................................................................................#15#
6.1&Control&system&LED&Show&T9................................................................................................................&15&
6.2&Control&system&LED&Studio....................................................................................................................&17&
6.3&Connection&to&the&mains&........................................................................................................................&18&
6.4&Installation&and&connection&of&the&PCI&sending&card&for&the&control&system&LED&studio&.......................&
19&
6.5&Connection&and&operation&of&the&external&sending&card&for&the&control&system&LED&Studio&.................&
20&
6.6&Function&test&with&the&interfaces&............................................................................................................&20&
7.#INSTALLATION#AND#CONFIGURATION#OF#THE#CONTROL#SYSTEMS#.............................................#21#
7.1&Control&system&LED&Show&T9................................................................................................................&21&
7.2&Testing&LED&Show&T9&and&playing&a&video&file&......................................................................................&29&
7.3&Control&system&LED&Studio....................................................................................................................&31&
7.4&Testing&LED&Studio&and&playing&a&video&file&..........................................................................................&37&
8.#CLEANING#AND#MAINTENANCE#.............................................................................................................#39#
8.1&Replacing&a&power&adaptor&....................................................................................................................&39&
8.2&Replacing&LEDs&....................................................................................................................................&42&
9.#PROBLEM#CART.......................................................................................................................................#44#
10.#TECHNICAL#SPECIFICATIONS...............................................................................................................#45#
Every person involved with the installation, operation and maintenance of this device has to
-be qualified
-follow the instructions of this manual
-consider this manual to be part of the total product
-keep this manual for the entire service life of the product
-pass this manual on to every further owner or user of the product
-download the latest version of the user manual from the Internet
1. INTRODUCTION
Thank you for having chosen aWiedamark Soft Display. If you follow the instructions given in this
manual, we are sure that you will enjoy this device for along period of time.
Software shown in the manual.
LED Show T9
For this user manual, [LED Show T9] was used with [Version 10.48].
Please download the latest software from our website. Wiedamark.com
and
LED Studio
For this user manual, [LED Studio] was used with [Version 10].
The software's user manual comes with the network control system.
Please download the latest software from our website. Wiedamark.com
2. SAFETY INSTRUCTIONS
CAUTION!&
Be#careful#with#your#operations.#With#a#dangerous#voltage#you#can#suffer#a#dangerous#
electric#shock#when#touching#the#wires!#
This device has left our premises in absolutely perfect condition. In order to maintain this
condition and to ensure asafe operation, itis absolutely necessary for the user to follow the
safety instructions and warning notes written in this user manual.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do
not switch it on immediately. The arising condensation water might damage your device. Leave
the device switched off until it has reached room temperature.
Please make sure that there are no obvious transport damages. Should you notice any damages
on the AC connection cable or on thecover, do not take thedevice into operation and
immediately consult your local dealer.
This device falls under protection-class II and features aprotective insulation. The voltage and
frequency must exactly bethesame asstated onthedevice. Wrong voltages orpower outlets
can lead to the destruction of the device and to mortal electrical shock.
Always plug in the power plug least. The power plug must always be inserted without force. Make
sure that the plug is tightly connected with the outlet.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution! Never touch them with wet hands, as this
could lead to mortal electrical shock.
Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never
operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal
electrical shock.
The cable insert or the female part in the device must never be strained. There must always be
sufficient cable to the device. Otherwise, the cable may be damaged which may lead to mortal
damage.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device
and the power-cord from time to time.
If extension cords are used, make sure that the core diameter is sufficient for the required power
consumption of the device. All warnings concerning the power cords are also valid for possible
extension cords.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise,
the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the
power switch is not accessible, the device must be disconnected via the mains.
If the power plug or the device is dusty, the device must be taken out of operation, disconnected
and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal
electrical shock. More severe dirt in and at the device should only be removed by a specialist.
There must never enter any liquid into power outlets, extension cords or any holes in the housing
of the device. If you suppose that also a minimal amount of liquid may have entered the device, it
must immediately
be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device
is still running, the device must be checked by a specialist if the liquid has reduced any insulation.
Reduced insulation can cause mortal electrical shock.
There must never be any objects entering into the device. This is especially valid for metal parts.
If any metal parts like staples or coarse metal chips enter into the device, the device must be
taken out of operation and disconnected immediately. Malfunction or short-circuits caused by
metal parts may cause mortal injuries.
Keep away children and amateurs!
Never leave this device running unattended.
3. OPERATING DETERMINATIONS
The flexible displays of the LSD series, quipped with extremely bright tri-color RGB LEDs, type
SMD 5050,
were specially designed for projection of videos and graphics synchronous to the computer. The
dispalys are made of bendable and foldable PVC material and can be easily suspended from
truss systems. The modular design allows the horizontal and vertical built-up of video screens,
indoor and outdoor. Control is via special PC software and network components (optionally
available).
This product is only allowed to be operated with the voltage given on the type plate.
This device is splash-proof (IP 44) and therefore qualified for indoor and outdoor use. For outdoor
use, the installer must always make sure to connect a rubber cable HO5RR-F. All valid
instructions concerning the installation of cables outdoors or in the ground must be adhered!
The ambient temperature must always be between -10° C and +45° C. Keep away from direct
insulation (particularly in cars) and heaters. The maximum relative humidity is 100 % with an
ambient temperature of 25° C. This device must only be operated in an altitude between -20 and
2000 m over NN.
Do not shake the device. Avoid brute force when installing or operating the device.
Before installing the system, make sure that the installation area can hold a minimum point load
of 4 times the system's load (e.g. weight 20 kg -point load 80 kg).
For overhead use (mounting height >100 cm), always secure the installation with an appropriate
secondary safety element (e.g. steel rope).
Make sure the area below the installation place is cordoned off when rigging, derigging or
servicing the device.
Do not connect displays to the mains while they are folded.
The F-symbol means: this device can be installed on normal inflammable surfaces.
The symbol determines the minimum distance from lighted objects. The minimum
distance between light output and the illuminated surface must be more than the given value.
The maximum ambient temperature Ta must never be exceeded.
Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and
damp cloth.
Please consider that unauthorized modifications on the device are forbidden due to safety
reasons!
If this device will be operated in any way different to the one described in this manual, the product
may suffer damages and the guarantee becomes void. Furthermore, any other operation may
lead to dangers like shortcircuit, burns, electric shock, lamp explosion, etc.
&
&
&
4. COMPONENTS OF A DISPLAY
e following describes all the components needed to operate an LED display. Some of the components are
used for other products as well.
1. Suspension point
2. Support bar
3. Data signal inputs (15-pin DIN plugs) for connec-
tion to the AIO network interface/receiver interface or
the previous display (number varies for each model)
4. Power cable for connection to a power outlet (90
- 260 V ~, 50/60 Hz) via the power plug or to the
feedthrough output of a previous display via the 2-pin
plug
5. 2-pin jack for the power supply (5 V DC) of the
AIO network interface/receiver interface
6. Front of the display, equipped with
tri-color RGB LEDs, type SMD 5050
7. Press buttons and hook-and-loop connectors
8. Feed-through output (2-pin jack with cap under the
protective cover) for power supply of the subsequent
display
9. Data signal outputs (15-pin DIN jacks) for connect-
ing a subsequent display
(number varies for each model)
10. Belts with hook, have combined
Working Load Limit (WLL) of 79 lbs (36 kg)
4.2 All-in-one network control system LED Show T9
AIO network interface and control soware LED Show T9
is complete set consisting of network interface and the control soware [LED Show T9] allows for control
of the displays together with a Windows PC and a gigabit ethernet network card (1000 Mbps). is system
does not require a further video card with DVI output, which makes it ideally suitable for mobile use with a
notebook. e transmission of the data signals with a screen resolution of up to 1280 x 1024 pixels from the
computer to the network interface is done via the supplied network cable. If needed, a standard CAT5e
network cable up to 100 meters long may be used.
For connecting displays the network interface oers eight data signal outputs, each allows control of 128
(width) x 16 (height) pixels. So one network interface can control 128 (width) x 128 (height) pixels in total. A
conguration with 256 (width) x 128 (height) pixels is also possible, however, results in a lower grayscale
resolution and data refresh rate. To built-up a large video wall with several displays (up to 1280 (width) x
1024 (height) pixels are possible), the network interfaces can be connected in series via network cables.
Minimum system requirements
• Windows 2000/XP
• Dual-core CPU >1.8 GHz
• >1 GB disk space
• Separate gigabit ethernet connection (1000 Mbps)
• 1024 x 768 screen resolution
Recommended system requirements
• 2.9 GHz dual-core CPU
• 4 GB disk space
• Realtek network card with RTL chip
00061810.DOC, Version 2.1
9/47
Block diagram
4-3 Block diagram LED Show T9
Connections of the AIO network interface
4-4 AIO network interface
Pixel control
per data cable 128 (width) x 16 (height) pixels
per AIO network interface 128 (width) x 128 (height) pixels
1Data signal outputs (15-pin DIN jacks)
1to 8 for connection to the displays
2POWER indicator
3Button Test mode for function tests
4Ethernet connection 2 (RJ45 jack),
feed-through output for connection to a
subsequent AIO network interface
5Ethernet connection 1 (RJ45 jack),
input for connection to the ethernet
network output (1000 Mbps are
required) of a computer or the previous
AIO network interface via the supplied
network cable
6Signal indicator, flashes constantly
when the data link is established
72-pin plug for connection to a display
for power supply (5 V DC) of the AIO
network interface
4.3 Network control system LED Studio
Receiver interface and PCI sending card or external DVI sending
card, each with LED Studio control soware
Control system consisting of receiver interface and PCI sending card with the control soware [LED Studio].
Contrary to the all-in-one network control system [LED Show T9], a computer with DVI output card and dual
display mode is required. e DVI output is connected to the sending card DVI input and then transmitted to
the receiver interface via the ethernet connectors. Alternatively to the PCI sending card a sending card with
external housing is available which makes the system perfect for rental use and mobile applications.
For connecting displays the receiver interface oers eight data signal outputs, each allows control of
128 (width) x 16 (height) pixels. So one receiver interface can control 128 (width) x 128 (height) pixels in
total. A conguration with 256 (width) x 128 (height) pixels is also possible, however, results in a lower
grayscale resolution and data refresh rate. To built-up a large video wall with several displays (up to 1280
(width) x 1024 (height) pixels are possible), the receiver interfaces can be connected in series via network
cables.
Minimum system requirements
• Windows 98/me/2000/NT/XP/Vista/ 7
• Video card with dual display mode and DVI output
• Free PCI slot
• Free USB port
Recommended system requirements
• 1024 x 768 screen resolution
• 2.9 GHz dual-core CPU
• 4 GB disk space
00061810.DOC, Version 2.1
11/47
Block diagram
4-8 Block diagram LED Studio
Connections of the PCI sending card
4-9 PCI sending card
1
Status LEDs,red: power supply failure,
green: normal working mode
2
Gigabit ethernet outputs (RJ45 jacks)
for connection to a receiver interface
left jack = U,right jack = D
3
Input for power supply (5 V DC) from
an external source (optional accessory)
with low-voltage plug (center contact =
positive pole)
Only used if the sending card is
operated externally of a computer
4
USB port for connection to the USB
port on the computer via the supplied
adapter cable
5
DVI input for connection to the DVI
output on the computer via the supplied
DVI cable
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Wiedamark Moniteur
