WhisperPower WhisperTouch WP 5.0 inch Manuel utilisateur
WP 5.0 inch | WP 7.0 inch | WP 10.0 inch
Enjoy Green Energy
Remote Control Panel
WhisperTouch
whisperpower.com
User Manual
2 WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch
WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch 3
Table of contents
1. Introduction 4
1.2 Firmware Revision 4
1.3 WPCI2000 Features (Touch display) 4
1.4 Quick Install 5
2. Installation 5
2.3 Mounting the WP Touch Display 5
2.4 Connecting the WP Touch Display 6
2.5 Checking Connections 8
3 ConguringtheWhisperPowerTouchDisplay 8
3.2 WhisperPower Touch Display screens 8
3.2.3 GENERATOR screen 9
3.2.4 SETTINGS screen 10
3.2.6 Settings screen in Installer mode 11
3.2.7 Authorization screen 12
3.2.8 EnergyCongurationscreen 12
3.2.9 GeneratorCongurationscreen 13
3.2.10 Display screen 14
4. Autostartingthegenerator 15
5. Troubleshooting 16
6. Dimensions 17
7. TechnicalSpecications 18
8. Appendix 18
9. TechnicalSupport 19
4 WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch
1. Introduction
Congratulations on your purchase of the WhisperPower Touch Display, displaying WPC in-
verter/ battery charger information, precise battery monitoring and/or WhisperPower Genera-
tor information. The WhisperPower Touch Display is available in 3 sizes: a 5 inch WP 5.0 Touch
(order number 40280100), the 7 inch WP 7.0 Touch (order number 40280101). WhisperPower
has designed and built this Touch Display to the highest standards for years of dependable
and accurate service. Inside the Touch panel, a WPCI 2000 interface has been integrated.
This WhisperPower Touch Display will only operate with a RS232-i interface (order number
60201084) which is connected to a WPC WhisperPower Centre inverter/charger, or con-
nected to a DDC connection of a WhisperPower Generator. Please read this manual carefully
and follow these instructions for installation, conguration, and usage of the WhisperPower
Touch panel in order to ensure optimal performance.
Functionallity:
1.2 Firmware Revision
ThismanualcorrespondstoycXXarmrmwarerevision1.0.
1.3 WPCI2000 Features (WhisperPower Touch display)
The WhisperPower Touch 5.0 and Touch 7.0 have the following features.
•Showing of WPC inverter/ battery charger information
•Showing of key Generator information
• Setting of WPC (On/O/Charge only and Current limit) by user
•Setting of Generator (Start/Stop) by user
• Setting of WPC parameters by qualied installer
• Setting of BSP parameters by qualied installer
• Setting of Generator parameters by qualied installer
PART NUMBER DESCRIPTON WPC SQ SERIE SC SERIE GV SERIE
40280100 TOUCH PANEL 5” Full Limited functionality, no Voltage,
Current and frequency setting. Only in
combination with WPC
40280101 TOUCH PANEL 7” Full
WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch 5
1.4 Quick Install
Installing the WhisperPower wpXXarm Touch Display involves the following steps. Please refer
to the individual sections for additional details.
1. Unpack the Box (Section 2.2)
3. Mount the Touch Panel (Section 2.3)
4. Connect the Touch panel (Section 2.5)
2. Installation
2.2 Unpacking the Box
When unpacking the box containing the WhisperPower Touch Display,
you should nd the following items:
1- The type of WhisperPower Touch Display you have ordered
1- A User’s Manual
1 - A RS232 Cable 1:1 connection to the WPC-RS232-I
1- RJ45 Converter cable/connector for generator cable
4- Screws with clip
If any of these items are missing or damaged, please contact WhisperPower.
2.3 Mounting the WhisperPower Touch Display
Install the Touch panel in vessel, vehicle or land based object. Take special care of the micro-
SD card on the side of the display. If the mounting hole is too narrow you could damage the
micro-SD card. Fix the panel with the 4 screws and clips.
2.4 Connecting the WhisperPower Touch Display
1. Remove the green 3 pole connector from rear side of the panel.
2. Connect the DC (plus and minus) and earth connection as shown on the rear side of the
panel.
3. Plug in again the 3 pole connector
4. Based on your situation connect the panel with the RS232 cable to the RS232-i serial inter-
face and connect the RS232-i serial interface to the WPC and/or connect the panel with
the RS485 cable to the generator as per schematic below
6 WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch
The WhisperPower Touch Displays provide a connection to a WPC-RS232-i
serial interface and a RS485 connection for the generator; these connections
can be found on the back of the device. The device is powered by an external
power source ranging from 6-42V DC.
Warning!
Do not use the starter battery of the generator
as power source for the Touch Display.
➜RS485
➜RS232
➜
+
➜ -
➜
WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch 7
not
used
not
used
Generator
Generator
RS232-i
RS232-i
WhisperPower Centre
WhisperPower Centre
➜
➜-
➜+
➜
➜-
➜+
➜
➜
+➜
- ➜
➜
➜
➜
➜
+
not
used
Generator
➜
➜
-
➜
+
➜
+
➜
-
➜
➜
WhisperPower Touch Display WP 5.0 inch Rear-side
WhisperPower Touch Display WP 7.0 inch Rear-side
WhisperPower Centre
RS232-i
RS232-i
8 WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch
2.5 Checking Connections
Once the connection to the WPC-RS232-i interface and the connection to the generator have
been completed, power can be supplied to the WhisperPower Touch Display. Check to see
that information is being properly transmitted by observing the ENERGY screen and/or the
GENERATOR screen. Refer to Section 4, “Troubleshooting”, if no information appears.
3 ConguringtheWhisperPowerTouchDisplay
As shipped from the factory, the WhisperPower Touch Displays don’t require any special
conguration and will work with all WhisperPower generators in combination with one or
more WPC’s. Congurations with more than one WhisperPower display is possible, for these
special congurations please contact WhisperPower.
3.2 WhisperPower Touch Display screens
3.2.1 Main screen
On the Main screen buttons are provided to enter the Energy, Generator and
Settings screens.
WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch 9
3.2.2 ENERGY screen
On the Energy screen the WPC status is shown. Input and output voltage and current, battery
voltage and current of the shunt and WPC (optional), charge state and remaining time of the
battery. The WPC can be turned on and o and also set in charge only mode. The current limit
can also be set.
3.2.3 GENERATOR screen
On the Generator screen the generator status is shown. The generator can be turned on and
o. The output voltage, current, power and frequency is shown together with the historical
and maintenance runtimes. Further the starter battery voltage is shown.
Charger
only
O
Charger
+ inverter
(combi
mode)
To set the current limit
➜
10 WhisperPower Touch Display WP 5.0, 7.0 and 10.0 inch
3.2.4 SETTINGS screen
On the Settings screen the in user mode buttons are shown to access the Maintenance,
Authorization, Display and System screens. After entering the appropriate Maintenance pass-
word the buttons Start Screen, Lock Brand, Energy Cong, Generator Cong, WPC Settings,
BSP Settings and WP Genset Settings are unlocked. These screens are meant for setting the
WhisperPower devices at installation time and are not meant for end users to avoid damage to
the equipment.
3.2.5Maintenancescreen(=passwordsettingscreen)
On the Maintenance screen the User Level of the WPC can be set from User to Basic, Expert,
Installer and Developer. These User Levels are protected by password to ensure proper set-
ting of the WPC installation. The WPC, battery pack and/or shunt can be damaged due to
improper settings.
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels WhisperPower Panneau de contrôle
