Whispbar K350 Manuel utilisateur
Fitting Kit
K350
ES
ESES
ES
Instrucciones de montaje para el
sistema de transporte.
F
FF
F
Instructions de montage pour Basic
Carrier
GB
GBGB
GB
Fitting Instructions for Basic Carrier
x 1 x 4 x 4 x 4
x 4 x 4
1
Revision No: 1.1B
Fitting Kit
K350
GB
MAX lbs
MAX lbs
W/P WHD W/P WHD
Toyota
Harrier , 5dr SUV 96- 03 NZ 143 143
2
Fitting Kit
K350
GB
First Time Installation
Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
This kit fits type A and B only.
These instructions show type A crossbar
fitted. They also apply to type B.
Use keys to remove covers.
3
Fitting Kit
K350
GB
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
Set bars to length (refer to the crossbar
instructions for crossbar adjustment).
Please check the rear of this manual for
information relating specifically to your
vehicle.
4
Fitting Kit
K350
GB
Tighten adjusting screw to 5 Nm (3.7 ft lb).
Remove clamp block by pressing backwards.
Select plastic internal block (from fitting kit)
and insert into foot.
Repeat for all legs.
5
Fitting Kit
K350
GB
Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
Make sure the pad fits into the holes
underneath the foot.
Fitment
Slide T-Slot square nuts into vehicle tracks.
Two per track.
The T-slot nuts should be placed where you
want the crossbars located.
Thread the grubscrew into the nut.
Using the supplied Hex Key, tighten
grubscrew into position.
Repeat for all four positions.
6
Fitting Kit
K350
GB
Place crossbar foot over grubscrews.
Tighten the red plastic knob. The side with
the nut showing should be facing up.
Ensure the red plastic knob is in the position
shown when fully tightened.
Repeat for all four positions.
7
Fitting Kit
K350
GB
Check crossbar is securely attached to the
vehicle.
Use keys to fit and lock covers
CAUTION:
CAUTION:CAUTION:
CAUTION:
Recheck all fasteners immediately after a load is
Recheck all fasteners immediately after a load is Recheck all fasteners immediately after a load is
Recheck all fasteners immediately after a load is
applied to the crossbars.
applied to the crossbars.applied to the crossbars.
applied to the crossbars.
Regularly check screws are tight.
Regularly check screws are tight.Regularly check screws are tight.
Regularly check screws are tight.
8
Fitting Kit
K350
GB
Maintenance
Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
Set crossbars a minimum distance of 700mm
(27 4/8") apart where no other distance is
specified in the fitting instructions. This is
especially important when carrying long
loads.
Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
Some sunroofs and radio antennae cannot
be used when the product is fitted.
Do not modify this product.
Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the fitting
instructions.
Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
Objects with pointed ends (skis) should be
carried with the pointed ends to the rear of
the vehicle.
Remove all loose or removable objects from
the load prior to loading.
Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
9
Fitting Kit
K350
GB
A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds, changing
of direction, and braking performance. Avoid
rapid acceleration and deceleration. Drive
carefully.
Note that the total height of the vehicle
increases when upright loads are carried.
Products should be locked during transport if
they have locks fitted.
Check and replace worn out or defective
parts.
Keep the product clean and maintained.
Never drive into a car wash with the roof rack
system fitted.
Lubricate locks and adjusting screws at
regular intervals.
Remove the products from the vehicle when
not in use. Make sure all loose parts are
stored safely.
Yakima Products, Inc.
15025 SW Koll Pkwy.
Beaverton, OR 97006-6056
USA
www.whispbar.com
10
Table des matières
Langues :
Autres manuels Whispbar Accessoires automobiles
Whispbar
Whispbar K604W Manuel utilisateur
Whispbar
Whispbar K043W Manuel utilisateur
Whispbar
Whispbar K670 Manuel utilisateur
Whispbar
Whispbar K822W Manuel utilisateur
Whispbar
Whispbar S44W Manuel d'utilisation et d'installation
Whispbar
Whispbar K416W Manuel d'utilisation et d'installation
Whispbar
Whispbar K403W Manuel d'utilisation et d'installation
Whispbar
Whispbar K805W Manuel utilisateur
Whispbar
Whispbar K197W Manuel utilisateur
Whispbar
Whispbar K188 Manuel utilisateur
Whispbar
Whispbar K436 Manuel utilisateur
Whispbar
Whispbar K855W Manuel d'utilisation et d'installation
Whispbar
Whispbar K421W Manuel utilisateur
Whispbar
Whispbar K838W Manuel d'utilisation et d'installation
Whispbar
Whispbar K727W Manuel d'utilisation et d'installation
Whispbar
Whispbar K308W Manuel utilisateur
Whispbar
Whispbar K624W Manuel utilisateur
Whispbar
Whispbar K717W Manuel d'utilisation et d'installation
Whispbar
Whispbar K583W Manuel utilisateur
Whispbar
Whispbar K587W Manuel utilisateur
