Whirlpool W10190965 Manuel utilisateur

INSTALLATION INSTRUCTIONS FOR ICE MAKER PART NO. W10190965

1. Unplug refrigerator or disconnect power.

2. Remove defective ice maker from freezer. The ice

maker may be held in place by three screws (Figure 1)

or by two clips and one screw (Figure 2).

IS025 (2/18)

To avoid risk of electrical shock, personal injury or death; disconnect electrical power before servicing.

WARNING! Electrical Shock Hazard

3. When replacing certain ice makers there will be a

mounting plate as an intregal part of the defective unit.

This must be removed and attached to the W10190965

(Figure 3).

FIG. 1 FIG. 2

4. Install lower bracket using the one on the defective unit

with a self tapping screw (Figure 4).

5. If the harness from the defective unit has a thermal

fuse, as shown in Figure 5A, reuse the harness. If the

harness does not have a thermal fuse or the thermal

fuse is blown, as shown in Figure 5B, you must

purchase a new wiring harness.

6. Remove knock-out from end as indicated in Figure 6.

FIG. 3

FIG. 4

FIG. 5A

FIG. 5B

Thermal fuses

7. Mount with screws removed from the defective unit.

Plug harness into the receptacle in freezer and mount

unit.

8. Check position of the inlet tube and position properly.

Make sure the shut off is in the down position.

9. Plug in refrigerator or reconnect power. It may take up

to 24 hours for your ice maker to begin producing ice.

FIG. 6

MODULE TEST POINTS Ejector blades or stripper: Remove module, motor, and

assembly. When reinstalling ejector blades, realign “D”

coupling with module cam.

SPECIFICATIONS

Mold heater – 185 watts, 72 ohms

Thermostat – Close 17˚ ±3˚

(Bimetal) Open 32˚ ±3˚

Water fill – 140 cc, 7.5 sec.

Motor – 1.5 watts, 8800 ohms

Module – Stamped circuit, plug-in connectors

Cycle – One revolution (ejects and water fill)

For 120 volt model

IS026 (2/18)

SERVICE SHEET FOR MODULAR ICE MAKER

To avoid risk of electrical shock, personal injury or death; disconnect electrical power before servicing.

WARNING! Electrical Shock Hazard

Unplug refrigerator or disconnect power.

SERVICE PROCEDURES

Cover: Pull water adjustment knob first and snap off

cover. Index knob and reinstall in same position for same

water fill.

Module, motor, and support assembly: Insert Phillips

driver in access ports in module. Loosen both screws.

Disconnect shut-off arm. Pull mold from support assembly.

Shut-off arm: Pull out from support. Reinstall to full depth.

Mold and heater: Remove module, motor, and support

assembly.

Bimetal: Remove module, motor, and support assembly.

Pull out retaining clips with bimetal.

Fill cup: Remove module, motor, and support assembly.

Remove ejector blades and shut-off arm. Pull fill cup from

mold.

Module ohmmeter checks

(no power to ice maker and ejector blades in park)

Test

Points Component Module Position Ohms

L - H Mold heater Attached to support 72

L - M Motor Disconnect from

support 8800

Module voltage checks with meter or test light

(power to ice maker)

Test

Points Component Line Voltage O Volts

L - N Module Power OK No power

T - H Bimetal Open Closed

L - H Heater On Off

L - M Motor On Off

N - V Water Valve On Off

WATER LEVEL ADJUSTMENT

Turning the screw clockwise decreases the water fill.

• 1/2 turn equals 20 cc or 1.2 sec.

• Full turn equals 40 cc or 2.4 sec.

• Maximum adjustment is one full turn in either direction.

Additional rotation could damage module.

Plug in refrigerator or reconnect power.

Table des matières

Autres manuels Whirlpool Machine à glaçons

Whirlpool

Whirlpool EZ CONNECT Manuel utilisateur

Whirlpool

Whirlpool GI15NDXTB4 Manuel utilisateur

Whirlpool

Whirlpool Cornelius JEACS50SLF1 Manuel utilisateur

Whirlpool

Whirlpool Ice Maker Manuel utilisateur

Whirlpool

Whirlpool GI15NFLTB1 Manuel utilisateur

Whirlpool

Whirlpool GI15NFRTS - Ice Maker Manuel utilisateur

Whirlpool

Whirlpool VERSA CUBER CH E-5R Manuel utilisateur

Whirlpool

Whirlpool ECKMF-281 Manuel utilisateur

Whirlpool

Whirlpool GI15NDXXB1 Manuel utilisateur

Whirlpool

Whirlpool AGB836/WP Manuel utilisateur

Whirlpool

Whirlpool ECKMF-64 Manuel utilisateur

Whirlpool

Whirlpool AGB 022 Manuel utilisateur

Whirlpool

Whirlpool AGB 024/01/G/WP Manuel utilisateur

Whirlpool

Whirlpool CHE-12RC Manuel utilisateur

Whirlpool

Whirlpool 50 Manuel utilisateur

Whirlpool

Whirlpool GI15NFRT Instructions d'utilisation

Whirlpool

Whirlpool 2180911 Manuel utilisateur

Whirlpool

Whirlpool GI15NFRXB0 Manuel utilisateur

Whirlpool

Whirlpool R-106 Guide d'installation

Whirlpool

Whirlpool WUI75X15HZ Manuel utilisateur

Whirlpool

Whirlpool K20 Manuel d'utilisation

Whirlpool

Whirlpool GI15NDXXS1 Manuel utilisateur

Whirlpool

Whirlpool WUI95X15HZ Manuel utilisateur

Whirlpool

Whirlpool ECKMF-831 Manuel utilisateur

Manuels Machine à glaçons populaires d'autres marques

Hoshizaki

Hoshizaki KMD-460MWJ Manuel utilisateur

Sub-Zero

Sub-Zero 315I Instructions d'utilisation

Unold

Unold 48945 Manuel utilisateur

Kenmore

Kenmore 2217402A Manuel utilisateur

Cornelius

Cornelius WM600 Mode d'emploi

GE XPIO43SCSS Manuel utilisateur

Hoshizaki

Hoshizaki KMD-901MAH Manuel utilisateur

Whynter

Whynter FIM-450HA Manuel utilisateur

U-Line

U-Line UMCR014-SC01A Manuel d'installation

Andrew James

Andrew James AJ000522 Manuel utilisateur

Scotsman

Scotsman CME1356 Manuel utilisateur

Scotsman

Scotsman ACM 25 Manuel utilisateur

Kärcher

Kärcher IP 120 Manuel utilisateur

U-Line

U-Line SS1095 Manuel utilisateur

Maytag

Maytag MIM1554WRS - Ice Maker Manuel utilisateur

Hoshizaki

Hoshizaki KM-630MAH Manuel utilisateur

Princess

Princess Yonanas Manuel utilisateur

Unold

Unold 48946 Manuel utilisateur