Whelen Engineering Company IS1 Series Manuel utilisateur

ENGINEERING COMPANY, INC IS1 SERIES

MICRO SIZE

STROBE BEACONS

IS1224P, 12-48 VDC, PIPE MOUNT

IS1120P, 120 VAC, PIPE MOUNT

IS1224S, 12-48 VDC, SURFACE MOUNT

IS1120S, 120 VAC, SURFACE MOUNT

IS124CP, 12-48 VDC, CAST, PIPE MOUNT

Doc No. 04-0113085-01

Route 145, Winthrop Road

Chester, CT06412-0684

TELEPHONE: (860) 526-9504

TOLL FREE: 1-800-637-4736

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996. 13085B

BASE

O RING SEAL

PCB ASSEMBLY

STROBE TUBE ASSEMBLY

#6-32 SCREW

CLAMP RING

DOME

STOP NUT

WARNING ALWAYS

DISCONNECT POWER

BEFORE SERVICING OR

INSTALLING AN IS1

SERIES BEACON.

SEE OTHER SIDE OF PAGE FOR

REPLACEMENT PARTS LISTING.

DESCRIPTION QTY. PART NUMBER

STROBE TUBE ASSEMBLY 1 01-0441319-00

DOME, AMBER 1 68-2130024-10

DOME, BLUE 1 68-2130024-20

DOME, CLEAR 1 68-2130024-30

DOME, GREEN 1 68-2130024-40

DOME, RED 1 68-2130024-50

O RING SEAL, PLASTIC BASE 1 38-0416442-00

GASKET, CAST BASE 1 38-0230104-00

MOUNTING INSTRUCTIONS

The IS1 Series Beacons are made for permanent

surface mount or pipe mount on a 1/2” NPT thread.

SURFACE MOUNT, PLASTIC BASE

1. Locate the wires in the wire slot and mount with

two screws. Make sure that the wires are in the wire

slot and not pinched under the Base.

PIPE MOUNT (Internal Thread)

1. Feed the power wires through the pipe.

2. Wire according to the WIRING instructions.

3. Screw the base onto the 1/2” NPT pipe and hand

tighten.

WIRING INSTRUCTIONS

MODELS IS1224P and IS1224S

MODEL IS124CP

1. Connect the RED wire to the positive DC

voltage (+).

2. Connect the BLACK wire to DC ground (-).

MODELS IS1120P and IS1120S

1. Connect the BLACK wire to the AC hot wire.

2. Connect the WHITE wire to the AC return wire.

Refer to the IS1 Series Product Sheet for current

draw to determine the proper wire gauge.

STROBE TUBE REPLACEMENT

1. Turn off power and wait 10 minutes.

2. Loosen the clamp ring screw and remove the

dome. Save the O Ring.

3. Press the tabs together on the Strobe Tube

Assembly and firmly pull the assembly out of the

PCB assembly. Do not pull the PCB Assembly away

from the Base.

4. Snap the replacement Strobe Tube Assembly into

the PCB Assembly. Roll the O Ring down the Base,

to get it in position. Position the Dome and secure

the clamp ring.

IS1 SERIES REPLACEMENT PARTS LISTING

3.4"

3.8" 2.5" DIA

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996.

Ce manuel convient aux modèles suivants

Autres manuels Whelen Engineering Company Système de sécurité

Whelen Engineering Company

Whelen Engineering Company 2004B Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 295SLSA5 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company WeCanX Traffic Advisor Module Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company WPS-2900 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company RB6PAPS Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 295HFS5 Series Instructions d'installation

Whelen Engineering Company

Whelen Engineering Company L21HAM Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company ECE 360 Class 1 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company B6LED Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company WS2100 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 2022 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 295HFSA5 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company Responder DX Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company RB6T Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 295HFS4 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 3012 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company SS361 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 2015 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company IS3 Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company IPS 400 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company ISB Series Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 1010 Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company 1502M Manuel utilisateur

Whelen Engineering Company

Whelen Engineering Company L21LAM Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur