WESTERSTRAND Mini WDP-Y Manuel utilisateur

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 1 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

General 2

Options 2

Installation 3

Configuration 4

DCF synchronisation 4

RDS/GPS synchronisation 4

Minute impulse synchronisation 4

Programming 5

General 5

Functions 5

Manual control 5

Set time– function F1 6

Set slave clock time– function F2 7

Relay output programming – function F3 8

Relay impulse length programming – function F4 9

Setting of impulse length for slave clock output – function F5 9

Setting of synchronisation source – function F6 10

Special functions 10

Program reset 10

Technical data 11

Programming form 12

User manual

Quartz master clock

WDP-Y mini

121346-00

R P

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 2 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

General

Quartz master clock WDP-Y mini with impulse output for operation of slave clocks.

The clock has a programmable relay output for control of, for example, illumination or pause signals.

The relay output can be programmed with 40 different ”signal points”.

A built-in temperature compensated quartz crystal oscillator gives high accuracy also when the ambient

temperature is varying. Optional time signal receivers can be connected for extra high accuracy. Minute impulse

synchronisation is also possible.

Changing from winter time to summer time and vice verse is fully automatic and does not need programming.

In case of power failure, an internal memory keeps the correct time for 24 hours.

Note: Activation or deactivation of the relay is not possible during power failure.

The connected slave clocks are corrected after the power failure by means of rapid impulsing.

The impulse output has a short-circuit protection with automatic reset.

In the event of short-circuit, the alarm LED is lit and outgoing impulses are inhibited.

Options

The following options can be used:

•Synchronisation DCF, art. no. 122984-20

•Synchronisation RDS, art. no. 122983-00

•Synchronisation GPS, art. no. 122982-00 (factory mounted option)

Programming buttons

Connection synchronisation

Connection minute impulse out

Connection 230VAC

Configuration switches for synchronisation

Relay output

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 3 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Installation

The master clock is intended for wall mounting.

The connectors are removable for easier installation.

•Mount the master clock with four screws.

•Connect the wires for the outgoing minute impulse.

•Connect the synchronisation source, if any. Check the

configuration switches before any synchronisation source is

connected. The master clock may be damaged if the wrong

setting is used. See ”Configuration” below.

•Connect the wires for the relay output.

•Connect the wires for 230VAC. When the clock is

permanently installed, a readily accessible disconnect

device shall be incorporated in the fixed wiring.

Installation fuse max. 10A.

Supply wire area: 1,5mm2.

145

100

Ø4

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 4 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Configuration

The master clock can be synchronised via minute impulse or radio DCF/RDS. This must be selected with the

switches at the edge of the front panel. Furthermore, correct type of synchronisation must be selected with

function F6; see “Programming”.

Note: The master clock may be damaged if the switches are in the wrong position.

DCF synchronisation

Set the switches like this: (2-wire)

RDS/GPS synchronisation

(GPS: The master clock must be prepared for GPS from factory)

Set the switches like this: (3-wire)

Minute impulse synchronisation

Set the switches like this:

Minute impulse

sync

+DCF

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 5 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Programming

General

Use the buttons R, F and P to program the clock.

RReturn Return to normal mode

FFunction Select function/Accept

PProgramming Change/Select.

The buttons are self-repeating if pressed for more than 0,7 s.

A total of 40 different signal points can be programmed. A signal point is a programming of the relay output at a

certain time and with a certain signal type, e.g. switch ON at 07.00 on Mondays.

Functions

Select with button F:

F1 Set time

F2 Set slave clock time

F3 Relay programming

F4 Impulse length for the relay output. This setting is relevant only when the output is programmed for

“Pulse” (1-59 sec).

F5 Set impulse length for the outgoing minute impulse (0,5-4,0 s.)

F6 Select synchronisation source (minute impulse or DCF)

Abbreviations used in the programming menus:

yyear

nmonth

dday

Hhour

nminute

Ssecond

Pprogram no.

Ssignal type

Eerased signal point

0switch OFF (relay contact open)

1switch ON (relay contact closed)

Ppulse (the relay is activated for a programmed time, 1-59 sec)

Wweekday

Manual control

With the clock in normal mode, the relay can be controlled manually by pressing button ”P”.

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 6 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Set time– function F1

Note! The complete routine must be worked through.

Press ”R” to enter normal mode. If time is not previously set, ”----” is

shown in the display. Press Funtil ”F1” is shown.

Function for programming of time. Select with P.

Year. Change with P. Accept with F.

Month. Change with P. Accept with F.

Date. Change with P. Accept with F.

Hour. Change with P. Accept with F.

Minute. Change with P. Set time one minute ahead of correct time and

await the minute shift. Press Fto synchronise.

Press Rto return to or continue with next function (press F).

- - - -

F 1

y 0 0

n 0 1

d 0 1

H 0 0

n 0 0

F 1

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 7 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Set slave clock time– function F2

When the clock is in normal mode, press Fto select function F2.

Function for correction of slave clocks. Select with P.

Note: Set the time shown by the slave clocks. The time of the slave clock

is automatically adjusted by rapid impulses or by inhibition of impulses.

Hour. Change with P. Accept with F.

Minute. Change with P. Accept with F.

Press Rto return or continue with the next function (press F).

Note: If the slave clock is one minute from correct time, reverse the slave clock connection wires.

F 2

H 0 0

n 0 0

F 2

2 3 . 5 9

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 8 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Relay output programming – function F3

When the clock is in normal mode, press Fto select function F3.

Relay programming. Select with P.

Signal point (program) 1. Change with P. Accept with F.

A total of 40 different signal points can be programmed.

Signal type. Change with P.

Select one of the following:

Eerased signal point

0switch OFF

1switch ON

Ppulse

Accept with F.

Weekday. Change with P.

Select one of the following:

1Monday

2Tuesday

3Wednesday

4Thursday

5Friday

6Saturday

7Sunday

8Monday-Friday

9All days in week

0Saturday-Sunday

Accept with F.

Hour. Change with P. Accept with F.

Minute. Change with P. Accept with F.

Press Rto return or continue with next function (press F).

F 3

P 0 1

S E

W 0

2 3 . 5 9

H 00

n 00

F 3

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 9 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Relay impulse length programming – function F4

When the clock is in normal mode, press Fto select function F4.

Pulse length. Select with P.

Number of seconds (1 to 59). Change with P.

Accept with F. Factory preset value is 6 seconds.

Press Rto return or continue with next function (press F).

Setting of impulse length for slave clock output – function F5

When the clock is in normal mode, press Fto select function F5.

An impulse length between 0,5 and 4,0 seconds can be selected.

Press Pto continue.

Impulse length in seconds (S). Change with P. Accept with F.

Press Rto return or continue with the next function (press F).

F 4

S 0 6

F 4

2 3 . 5 9

F 5

S 2 . 0

F 5

2 3 . 5 9

Document: 1632en03.doc

WESTERSTRAND Author: CAn

Date: 2003-09-03

Page: 10 of 12

WESTERSTRAND URFABRIK AB

Box 133 Tel. +46 506 48000 Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA Fax. +46 506 48051 e-mail: info@westerstrand.se

Setting of synchronisation source – function F6

The master clock is prepared for synchronisation via DCF/RDS (GPS optional) or minute impulse.

When the master clock is synchronised, the dot between hours and minutes is flashing each second.

When the clock is in normal mode, press Fto select function F6.

Function for selection of synchronisation source. DCF (RDS/GPS) or

minute impulse (1/1 minute) can be selected. Select with P.

Sy dC = DCF (or RDS/GPS)

Sy Im = Minute impulse

Change with P. Accept with F.

Press Rto return or continue with the next function (press F).

Special functions

To erase all programmed signal points for the relay output:

1) Turn OFF the master clock.

2) Press buttons Rand Pwhile the master clock is turned on.

The message ”dELE” is displayed, indicating that the erasure is completed.

Program reset

Restart of the master clock program. Already programmed signal points for the relay are intact but the real time

must be programmed with function F1 (and F2 for the slave clocks).

1) Turn OFF the master clock.

2) Press buttons R, Fand Pwhile the master clock is turned on.

The clock is restarted and ”- - - - ” is shown in the display.

F 6

S y d C

F 6

2 3 . 5 9

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels WESTERSTRAND Horloge

WESTERSTRAND

WESTERSTRAND CIRCLE LINE Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Analogue clock Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Analog indoor clock with WiFi Manuel utilisateur

WESTERSTRAND

WESTERSTRAND QWTIME III WDP M+S Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuel utilisateur

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Lumex 5 Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuel utilisateur

WESTERSTRAND

WESTERSTRAND KNX Manuel utilisateur

WESTERSTRAND

WESTERSTRAND QUARTZ CLOCK Manuel utilisateur

WESTERSTRAND

WESTERSTRAND QUARTZ MOVEMENT Manuel utilisateur

WESTERSTRAND

WESTERSTRAND AUREA ALPHA Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Lumex 5 Manuel utilisateur

WESTERSTRAND

WESTERSTRAND CIRCLE LINE Manuel utilisateur

WESTERSTRAND

WESTERSTRAND AUREA II Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Lumex 5 Manuel utilisateur

WESTERSTRAND

WESTERSTRAND LUMEX 7 Manuel utilisateur

WESTERSTRAND

WESTERSTRAND QWTIME III WDP-WL Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Wireless Clock Manuel utilisateur

WESTERSTRAND

WESTERSTRAND Quartz Movement Manuel utilisateur

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP PoE Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur

WESTERSTRAND mini WDP-Y Manuel utilisateur

Manuels Horloge populaires d'autres marques