Weslo Pro 13.8e Elliptical Manuel utilisateur

Serial

Number

Decal

Model No. 30875.1

Serial No.

Write the serial number in the

space above for reference.

USERʼS MANUA

QUESTIONS?

If you have questions, or if parts are

damaged or missing, P EASE

CONTACT OUR CUSTOMER SER-

VICE DEPARTMENT DIRECT Y.

CA TO -FREE:

1-888-936-4266

Mon.–Fri., 7:30 until 16:30 ET

(excluding holidays)

OR E-MAI US:

[email protected]

www.weslo.com

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

TAB E OF CONTENTS

WARNINGDECA P ACEMENT ..............................................................2

IMPORTANTPRECAUTIONS ................................................................3

BEFOREYOUBEGIN ......................................................................4

ASSEMB Y ...............................................................................5

HOWTOUSETHEE IPTICA EXERCISER ..................................................11

MAINTENANCEANDTROUB ESHOOTING ...................................................18

EXERCISEGUIDE INES ...................................................................19

PART IST ..............................................................................20

EXP ODEDDRAWING ....................................................................22

ORDERINGREP ACEMENTPARTS ..................................................BackCover

IMITEDWARRANTY ..............................................................BackCover

WARNING DECA P ACEMENT

This drawing shows the location(s) of the

warning decal(s). If a decal is missing or

illegible, see the front cover of this

manual and request a free replacement

decal. Apply the decal in the location

shown. Note: The decal(s) may not be

shown at actual size.

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical exerciser are

adequately informed of all precautions.

3. Your elliptical exerciser is intended for home

use only. Do not use your elliptical exerciser

in a commercial, rental, or institutional set-

ting.

4. Keep your elliptical exerciser indoors, away

from moisture and dust. Place your elliptical

exerciser on a level surface, with a mat

beneath it to protect the floor or carpet.

Make sure that there is at least 3 ft. (0.9 m)

of clearance in the front and rear of your

elliptical exerciser and 2 ft. (0.6 m) on each

side.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from your elliptical exerciser at all times.

7. Your elliptical exerciser should not be used

by persons weighing more than 250 lbs.

(113 kg).

8. Wear appropriate exercise clothes when

exercising; do not wear loose clothes that

could become caught on your elliptical exer-

ciser. Always wear athletic shoes for foot

protection.

9. Hold the handgrip pulse sensor or the upper

body arms when mounting, dismounting, or

using your elliptical exerciser.

10. Keep your back straight while using your

elliptical exerciser; do not arch your back.

11. The pulse sensor is not a medical device.

Various factors, including the userʼs move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

12. When you stop exercising, allow the pedals

to slowly come to a stop.

13. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

14. Use your elliptical exerciser only as

described in this manual.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical exerciser before using your elliptical

exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN

Pulse Sensor

Upper Body Arm

Pedal Disc

Wheel

Adjustment Knob

Pedal

Console

Water Bottle Holder*

Fan

*Water bottle is not included

Thank you for selecting the new WES O PRO™

13.8E elliptical exerciser. The 13.8E elliptical exerciser

provides a selection of features designed to make

your workouts at home more effective and enjoyable

For your benefit, read this manual carefully before

you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front

cover of this manual. To help us assist you, note the

product model number and serial number before con-

tacting us. The model number and the location of the

serial number decal are shown on the front cover of

this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

M10 x 112mm Carriage Bolt (34)–4

M10 x 88mm Button Screw (63)–2

M10 x 55mm Bolt Set (27)–2

M10 Split

Washer (70)–2

M8 Large

Washer (53)–10

Wave Washer

(95)–2

M8 Split

Washer (100)–4

M8 x 65mm Button Screw (99)–4

M8 x 50mm Button

Screw (89)–4

M10 Locknut

(29)–4

M8 Locknut

(46)–12

M4 x 16mm

Screw (66)–4

M4 x 22mm

Screw (91)–2

M8 x 25mm Patch

Screw (22)–2

M8 x 45mm Button

Bolt (50)–4

M8 x 38mm Button

Bolt (112)–4

ASSEMB Y

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires a Phillips screwdriver , an adjustable

wrench , and a rubber mallet .

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-

ses below each drawing is the key number of the part, from the PART IST near the end of this manual. The

number following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware

kit, check to see if it has been preassembled.

Identify the Front Stabilizer (3). Make sure that

the Front Stabilizer is turned so that the

Wheels (32) are not touching the floor.

While another person lifts the front of the Frame

(1), attach the Front Stabilizer (3) to the Frame

with two M10 x 112mm Carriage Bolts (34) and

two M10 ocknuts (29).

2. While another person lifts the rear of the Frame

(1), attach the Rear Stabilizer (4) to the Frame

with two M10 x 112mm Carriage Bolts (34) and

two M10 ocknuts (29).

To make assembly easier, read the

information on page 5 before you begin.

105

3. While another person holds the Upright (2) near

the Frame (1), connect the Upper Wire Harness

(86) to the ower Wire Harness (87).

Tip: Avoid pinching the Wire Harnesses (86,

87). Insert the Upright (2) into the Frame (1).

Next, slide an M10 Split Washer (70) and a

Frame Spacer (83) onto each of the two M10 x

88mm Button Screws (63).

Insert the M10 x 88mm Button Screws (63) into

the Frame (1) and the Upright (2). Make sure

that the concave sides of the Frame Spacers

(83) are facing the Frame. Do not tighten the

Button Screws yet.

Attach the Water Bottle Holder (105) to the

Upright (2) with two M4 x 22mm Screws (91).

Avoid pinching the Wire

Harnesses (86, 87)

4. Identify the eft Pulse Bar (107), which is

marked with a “ eft” sticker.

Have another person hold the eft Pulse Bar

(107) near the left side of the Upright (2). Make

sure that the hexagonal holes are in the

indicated location.

See the inset drawing. ocate the wire tie in

the Upright (2). Tie the lower end of the wire tie

to the left Pulse Wire (113). Next, pull the upper

end of the wire tie upward out of the top of the

Upright. Then, untie and discard the wire tie.

Tip: Avoid pinching the wires. Slide the eft

Pulse Bar (107) onto the Upright (2). Attach the

eft Pulse Bar with two M8 x 38mm Button

Bolts (112) and two M8 ocknuts (46). Make

sure that the ocknuts are in the hexagonal

holes.

Repeat this step for the Right Pulse Bar

(108).

107

108

112

113

Hexagonal

Holes

Avoid pinching

the wires

Wire Ties

Wire Tie

113

5. The Console (5) can use four D batteries (not

included); alkaline batteries are recommended.

IMPORTANT: If the Console has been

exposed to cold temperatures, allow it to

warm to room temperature before inserting

batteries. Otherwise, you may damage the

console displays or other electronic compo-

nents. Remove the battery cover, insert the bat-

teries into the battery compartment, and reat-

tach the battery cover. Make sure to orient the

batteries as shown by the diagram inside the

battery compartment.

To purchase an optional AC adapter, contact

the store where you purchased this product

or call the telephone number on the cover of

this manual. To avoid damaging the console,

use only a manufacturer-supplied AC

adapter. Plug one end of the AC adapter into

the jack on the console; plug the other end into

an outlet installed in accordance with all local

codes and ordinances.

Batteries

Battery

Cover

6. While another person holds the Console (5)

near the Upright (2), connect the console wire

to the Upper Wire Harness (86). Then, connect

the console pulse wires to the Pulse Wires

(113). Insert the excess wire downward into the

Upright.

Tip: Avoid pinching the wires. Attach the

Console (5) to the Upright (2) with four M4 x

16mm Screws (66).

113

Console

Wire

Pulse

Wires

7. Identify the eft Upper Body Arm (9), which is

marked with a “ eft” sticker.

Insert the eft Upper Body Arm (9) into an

Upper Body eg (79). Make sure that the

hexagonal holes are in the indicated loca-

tion.

Attach the eft Upper Body Arm (9) to the

Upper Body eg (79) with two M8 x 45mm

Button Bolts (50) and two M8 ocknuts (46).

Make sure that the ocknuts are inside the

hexagonal holes. Do not tighten the Button

Bolts yet.

Repeat this step for the Right Upper Body

Arm (not shown) and the other Upper Body

eg (not shown).

8. Apply a generous amount of the included

grease to the Pivot Axle (97) and to two Wave

Washers (95).

Insert the Pivot Axle (97) into the Upright (2).

Slide a Upper Body Arm Spacer (25) onto the

short tube on the eft Upper Body Arm (9), and

rotate the Upper Body Arm Spacer so that the

small arrow is pointing toward the floor.

Slide a Wave Washer (95) onto the left end of

the Pivot Axle (97). Then, slide the eft Upper

Body Arm (9) onto the left end of the Pivot Axle.

Repeat this action for the Right Upper Body

Arm (10).

Hexagonal

Holes

Grease

Tube

Arrow

10. Apply grease to the barrel of an M10 x 55mm

Bolt Set (27) and to the two eg Bushings (28)

in the left Upper Body eg (79).

Attach the left Upper Body eg (79) to the eft

Pedal Arm (14) with the M10 x 55mm Bolt Set

(27). Do not overtighten the Bolt Set; the left

Upper Body eg must pivot freely.

Attach the right Upper Body eg (79) to the

Right Pedal Arm (103) in the same way.

See step 3. Tighten the M10 x 88mm Button

Screws (63).

See step 7. Tighten the M8 x 45mm Button

Bolts (50) in the Upper Body egs (79).

103

28 28

Grease

22 53

9. Tighten an M8 x 25mm Patch Screw (22) and an

M8 arge Washer (53) into each end of the Pivot

Axle (97).

Attach the Axle Caps (23) by pressing the small

tabs into the Upper Body Arm Spacers (25).

12. Make sure that all parts are properly tightened. Note: Some hardware may be left over after assembly is

completed. To protect the floor or carpet from damage, place a mat under the elliptical exerciser.

11. Attach a Pedal Bracket (16) to the eft Pedal

Arm (14) with two M8 x 65mm Button Screws

(99), two M8 arge Washers (53), and two M8

ocknuts (46).

Identify the eft Pedal (13), which is marked

with a “ eft” sticker. Attach the eft Pedal to the

eft Pedal Arm (14) with two M8 x 50mm Button

Screws (89), two M8 Split Washers (100), and

two M8 arge Washers (53).

Attach the other Pedal Bracket (not shown)

and the Right Pedal (12) to the Right Pedal

Arm (103) in the same way.

103

100

Autres manuels pour Pro 13.8e Elliptical

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Weslo vélo elliptique

Weslo

Weslo WLEL45070 Manuel utilisateur

Weslo

Weslo Momentum 750 Elliptical Manuel utilisateur

Weslo

Weslo Momentum 620 Elliptical Manuel utilisateur

Weslo

Weslo Momentum 615 Elliptical Manuel utilisateur

Weslo

Weslo Momentum 4.0 Elliptical Guide de configuration

Weslo

Weslo Momentum 4.0 Elliptical Manuel d'utilisation et d'entretien

Weslo

Weslo Momentum Ct5.8 Elliptical Manuel utilisateur

Weslo

Weslo Momentum 410 Elliptical Guide de l'utilisateur

Weslo

Weslo ALTA Manuel utilisateur

Weslo

Weslo MOMENTUM ELLIPTICAL Manuel utilisateur

Weslo

Weslo Momentum 4.8 Elliptical Manuel utilisateur

Weslo

Weslo Momentum G 3.2 Elliptical Manuel utilisateur

Weslo

Weslo Momentum R 4.2 Elliptical Manuel utilisateur

Weslo

Weslo PURSUIT E25 Manuel utilisateur

Weslo

Weslo Momentum 220X WLEL2006.0 Manuel utilisateur

Weslo

Weslo Momentum 800 Elliptical Manuel utilisateur

Weslo

Weslo MOMENTUM G4.1 Manuel utilisateur

Weslo

Weslo EasyFit WLIVEL63110.0 Manuel utilisateur

Weslo

Weslo Momentum 605 Elliptical Manuel d'utilisation et d'entretien

Weslo

Weslo Momentum 800 Elliptical Manuel utilisateur

Weslo

Weslo Momentum CT 5.9 Manuel utilisateur

Weslo

Weslo Elliptical Glider 2.0 Manuel utilisateur

Weslo

Weslo Momentum5.9 Elliptical Manuel utilisateur

Weslo

Weslo WLEL29040 Manuel utilisateur

Manuels vélo elliptique populaires d'autres marques

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuel utilisateur

Torque Fitness

Torque Fitness XPLLP Manuel utilisateur

Octane Fitness

Octane Fitness PRO3700C Manuel utilisateur

Xterra

Xterra FS5.8e Manuel utilisateur

Bodyguard

Bodyguard E-40 Manuel utilisateur

Bonn Germany

Bonn Germany Concept 2.2 Manuel utilisateur

Precor

Precor Resolute RSL 620 Manuel utilisateur

NordicTrack

NordicTrack E 9.2 Elliptical Manuel utilisateur

Vision Fitness

Vision Fitness X6600iNetTV Manuel utilisateur

Matrix

Matrix MX-A5x Manuel utilisateur

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuel utilisateur

Sears

Sears FREE SPIRIT C249 30737 0 Manuel utilisateur

True

True FS-64 Manuel utilisateur

Sport-thieme

Sport-thieme ST 310 Manuel utilisateur

VIRTUFIT

VIRTUFIT CTR 1.1 Manuel utilisateur

Kettler

Kettler GIRO C 1 Manuel utilisateur

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuel utilisateur

Reebok

Reebok 1000 Zx Elliptical Manuel utilisateur