Wen 10165 Manuel utilisateur

Your new device has been engineered and manufactured to WEN’s highest standards for dependability, ease of

operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-

free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use your

device properly and for its intended purpose, you will enjoy years of safe, reliable service.

IMPORTANT:

MODEL 10165

65-FOOT LASER

DISTANCE MEASURE

NEED HELP? CONTACT US!

Have product questions? Need technical support?

Please feel free to contact us at:

NOTICE: Please refer to wenproducts.com for the most up-to-date instruction manual.

TABLE OF CONTENTS

Specifications........................................................................................... 2

Introduction ............................................................................................. 3

General Safety Rules................................................................................ 4

Specific Safety Rules for the Laser Distance Measure ............................. 6

Know Your Laser Distance Measure....................................................... 11

Operation ............................................................................................... 12

Maintenance........................................................................................... 14

Troubleshooting Guide........................................................................... 15

Exploded View & Parts List.................................................................... 16

Warranty Statement ............................................................................... 18

SPECIFICATIONS

Model Number 10165

Laser Type 650 nm, <1 mW

Laser Class II

Battery (2) AAA Batteries (not included)

Operating Temperature 14°F - 104°F

Measuring Distance 65 feet

Measuring Accuracy ±3.0 mm (1/8 inch)

Measuring Distance 0.16 - 65.5 feet

Weight 3.5 oz (with batteries)

Dimensions 1-5/8 x 1 x 4-3/8 inches

INTRODUCTION

Thanks for purchasing the WEN Laser Distance Measure. We know you are excited to put your device to work,

but first, please take a moment to read through the manual. Safe operation of this device requires that you read

and understand this operator’s manual and all the labels affixed to the device. This manual provides information

regarding potential safety concerns, as well as helpful assembly and operating instructions for your device.

NOTE: The following safety information is not meant to cover all possible conditions and situations that may occur.

WEN reserves the right to change this product and specifications at any time without prior notice.

Keep this manual available to all users during the entire life of the device and review it frequently to maxi-

mize safety for both yourself and others.

SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. The safety symbols and the explanations

with them deserve your careful attention and understanding. Always follow the safety precautions to reduce the

risk of fire, electric shock and personal injury. However, please note that these instructions and warnings are

not substitutes for proper accident prevention measures.

SPECIFIC SAFETY RULES FOR THE LASER DISTANCE MEASURE

WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety

rules. Failure to follow the safety instructions may result in serious personal injury.

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

WARNING: LASER RADIATION. Class 2 laser. DO NOT STARE INTO THE BEAM.

1. Device purpose. This Laser Distance Measure is designed to measure distances, lengths, heights, clearances,

areas and volumes. The measuring tool can be used both indoors and outdoors. Using the device for any other

purpose for which it is not designed may result in serious injuries, dangerous radiation exposure, device damage,

and voiding of the warranty.

2. Never shine the laser in your eyes or the eyes of other people or animals. This can cause permanent damage

to eyes. Do not look directly into the laser beam with unprotected eyes. Never look into the path of the beam.

3. If laser radiation strikes your eye, you must deliberately close your eyes and immediately turn your head

away from the beam.

4. Never point the laser beam towards reflecting surfaces. Never point the laser towards people or animals. Even

a laser beam with a low output can cause damage to the eyes.

5. Do not allow children to use the laser measuring tool. They could unintentionally blind other persons or them-

selves.

6. Device inspection. Before operation, check the device and batteries for any damage or missing parts. Do not use

the device if any part is missing or damaged. Make sure all adjustments are correct and all connections are tight.

7. Do not try to open or disassemble your measuring device. Never open the laser module as unexpected exposure

to the beam can occur. The laser cannot be replaced with a different type of laser.

8. Cleaning. Never use solvents to clean plastic parts. Solvents could dissolve or otherwise damage the material.

Use only a soft damp cloth to clean plastic parts.

9. Do not make any modifications to the laser equipment. Have the measuring device repaired only by qualified

specialists.

Safety is a combination of common sense, staying alert and knowing how your item works.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING: Read and understand all warnings, cautions and operating instructions before using this

device. Failure to follow all instructions listed below may result in personal injury and device damage.

WARNING: LASER RADIATION. Class 2 laser. DO NOT STARE INTO THE BEAM.

SPECIFIC SAFETY RULES FOR THE LASER DISTANCE MEASURE

WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety

rules. Failure to follow the safety instructions may result in serious personal injury.

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

Safety is a combination of common sense, staying alert and knowing how your item works.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING: Read and understand all warnings, cautions and operating instructions before using this

device. Failure to follow all instructions listed below may result in personal injury and device damage.

10. Replacements. Should any component of your Laser Distance Measure be missing/damaged or fail in any

way, turn the device off. Replace the missing, damaged, or failed parts using only identical replacement parts

before resuming operation.

11. Do not leave the switched-on measuring device unattended. Switch the measuring tool OFF after use. Other

persons could be blinded by the laser beam.

12. Protect the measuring device against moisture and direct sunlight. Store in a dry, shaded location. Do not

store at temperatures lower than 14°F or higher than 104°F.

13. Do not subject the measuring device to extreme temperatures or variations in temperature. For example,

do not leave the measuring device in cars for extended periods of time. In case of large variations in temperature,

allow the measuring tool to adjust to the ambient temperature before using it. The measuring device should stay

within the temperature range of 14°F - 104°F.

14. Avoid heavy impact and dropping of the measuring device. If the device is dropped or damaged, perform

an accuracy test before resuming operation. Replace the missing, damaged, or failed parts using only identical

replacement parts before resuming operation.

15. Remove the batteries before storing for an extended period of time.

16. DO NOT point the laser beam into the sky and/or at an aircraft.

These safety instructions can’t possibly warn of every scenario that may arise with this device,

always make sure to stay alert and use common sense during operation.

KNOW YOUR LASER DISTANCE MEASURE

DEVICE PURPOSE

Laser Distance Measures are great for measuring distances, lengths, heights, clearances, areas, and volumes. Refer

to the diagram below to become familiarized with the parts and functions of your Laser Distance Measure.

DISPLAY FUNCTIONS

Use the diagram to the right to learn about the

various icons on your laser distance measure.

A. Laser ON/OFF

B. Length Measurement

C. Area/Volume Measurement

• Area

• Volume

D. Error/Service Needed

E. Battery Level

F. Measurement Reference

• Top

• Base

G. Previous Measurement Value

H. Current Measurement/Area/Volume

I. Unit (m/ft/in/' ")

Laser Beam Outlet

DO NOT POINT AT EYES

Battery Cover

Reception Lens Mode

Measuring/ON

ON/OFF

B C D E

TURNING ON/OFF

Turning ON: To turn your measuring device ON, you can either press the power button or the measuring but-

ton .

Turning OFF: To turn your measuring device OFF, hold the power button for 1-2 seconds then release it.

Automatic OFF: The device will automatically shut off after 3 minutes of inactivity to prolong battery life.

ASSEMBLY & ADJUSTMENTS

WARNING: Do not turn on the device until it is fully assembled according to the instructions. Failure to

follow the safety instructions may result in serious personal injury.

NOTE: Always replace both batteries at the same time. Do not use different brands or types of batteries/rechargeable

batteries together.

INSTALLING/REMOVING BATTERIES

Your Laser Distance Measure requires two (2) AAA standard or re-

chargeable batteries (not included).

NOTE: More measurements are possible when using 1.5V rechargeable

batteries rather than 1.2V rechargeable batteries.

1. Push the tab (Fig. 1 - 1) inwards and pull upwards to remove the bat-

tery cover (Fig. 1 - 2).

2. Insert two AAA batteries (not included) into the battery compartment

(Fig. 1 - 3). Follow the diagram inside of the battery compartment to

place the batteries in the correct orientation.

3. Replace the battery cover (Fig. 1 - 2) and press into place.

Fig. 1

WARNING: Remove the batteries from the measuring device when not in use for long periods of time.

The batteries can corrode and self-discharge when left in the device for a long period of time.

OPERATION

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

OPERATION

UNIT SELECTION

You can use your device to measure in four different units. The available units are: meters (m), feet (ft), inches

(in), and feet/inches (' ").

NOTE: The feet or inches units will give you measurements in decimals, whereas the feet/inches unit will give you

measurements in a combination of whole feet and whole inches.

To switch between units: While holding the mode button , press the measurement button until your de-

sired unit is displayed on the screen.

CHANGING MODES

After powering your measuring device ON, the default mode is distance measurement . To switch to a different

mode (distance /area /volume ) press the mode button . In the following sections, you can find more

information about how to use each mode.

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

SELECTING THE MEASURING REFERENCE POINT

You can set your measuring device to measure from either the base of the unit or from the top of the unit. See

Figures 2 and 3 below to learn more about the two reference point options.

To change the reference point: While holding the mode button , press the power button to switch between

reference points.

Fig. 2 Fig. 3

From the Base From the Top

NOTE:The measurement value appears after a few seconds. The measurement will take longer to appear

depending on the distance, light conditions, and reflective properties of the target surface. The end of the mea-

surement is indicated by a tone. The laser beam automatically shuts off after the measurement is completed.

MEASURING A DISTANCE

The distance measuring function is for measuring distances, lengths, heights, and clearances. This

function is depicted by the arrow symbol .

OPERATION

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

1. Make sure you are in distance measuring mode depicted by the ar-

row symbol . If you’re in a different mode, press the mode button

until you see the arrow symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser at the point of measurement.

4. Press the measurement button again to take the measurement.

The value will be seen on your display. Your screen will look like Fig. 4.

MEASURING AN AREA

The area measuring function is made for calculating the area of a rect-

angular space. This function is depicted by the area symbol .

1. Make sure you are in area measuring mode depicted by the area

symbol . If you’re in a different mode, press the mode button un-

til you see the area symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser to measure the length. Press

the measurement button again to take the measurement. The

value will be seen on your display.

4. Repeat step 3 to measure the width. The area will automatically cal-

culate after the second measurement is taken. The value of the width

measurement will be seen on the top row of your screen and the area

will be on the bottom. Your screen will look like Fig. 5.

NOTE: A line will appear on the edge of the area symbol to indi-

cate which measurement you are recording.

Fig. 4

NOTE: The laser will automatically

shut off after 30 seconds of inactiv-

ity to prolong battery life and limit

accidents.

NOTE: The bottom number on your

display is the current measurement

being recorded. If you take multiple

measurements, the previous mea-

surement moves to the top row.

Laser ON/OFF Distance Mode

Battery

Level

Units

Measurement

Current

Measurement

Fig. 5

Laser ON/OFF Area Mode

Battery

Level

Units

Measurement Area

1. Make sure you are in distance measuring mode depicted by the arrow symbol . If you’re in a different mode,

press the mode button until you see the arrow symbol on the screen.

2. Make sure to set your measuring device’s reference point and units (see p. 8).

3. Hold down the measurement button for two seconds. You are now in continuous measuring mode. As the

distance between the reference point and target point changes, the measurement will update on the screen and

you will hear a tone. Press the measurement button to exit continuous measuring mode.

NOTE: The device will not save the measurements while you are in continuous measuring mode. The laser stays

on the duration of the continuous measurement. DO NOT shine the laser towards people or animals.

MEASURING VOLUME

The volume measuring function is made for measuring the volume of a rectangular prismatic space. This function

is depicted by the cube symbol .

OPERATION

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reflected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

1. Make sure you are in volume measuring mode depicted by the

cube symbol . If you’re in a different mode, press the mode button

until you see the cube symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser to measure the length. Press

the measurement button again to take the measurement. The

value will be seen on your display.

4. Repeat step 3 two more times to measure the width, and height.

The volume will automatically calculate after the third measurement is

taken. The value of the last measurement will be seen on the top row

of your screen and the volume will be on the bottom. Your screen will

look like Fig. 6.

NOTE: A line will appear on the edge of the volume symbol to

indicate which measurement you are recording.

CONTINUOUS MEASURING

The continuous measuring setting allows you to move the device and

receive updated measurements every few seconds.

Fig. 6

NOTE: The laser will automatically

shut off after 30 seconds of inactiv-

ity to prolong battery life and limit

accidents.

NOTE: The bottom number on your

display is the current measurement

being recorded. If you take multiple

measurements, the previous mea-

surement moves to the top row.

Laser ON/OFF Volume Mode

Battery

Level

Units

Measurement Volume

Table des matières

Autres manuels Wen Instrument analytique

Wen

Wen 10110 Manuel utilisateur

Manuels Instrument analytique populaires d'autres marques

Cocraft

Cocraft NLT04 Manuel utilisateur

M&C

M&C GENTWO PMA1000 Manuel utilisateur

MICRO-EPSILON

MICRO-EPSILON optoncdt 1700 Manuel utilisateur

CONDTROL

CONDTROL XP4 PRO Manuel utilisateur

Extech Instruments

Extech Instruments BR200 Manuel utilisateur

Dewetron

Dewetron DEWE-30-16 Manuel du produit

EXTOL PREMIUM

EXTOL PREMIUM 8820043 Instructions d'installation et d'utilisation

RIDGID

RIDGID SeeSnake Compact Manuel utilisateur

Teledyne

Teledyne 3000PA Manuel utilisateur

YDLIDAR

YDLIDAR TIA Manuel utilisateur

Olympus

Olympus IPLEX FX Series Manuel utilisateur

Bosch

Bosch GLM 50 C Professional Manuel utilisateur

Reflecta

Reflecta DigiEndoscope Manuel utilisateur

Chinavision

Chinavision CVACZ-G696 Instructions de montage

Fuji Electric

Fuji Electric ZKMA Manuel utilisateur

Teledyne

Teledyne 3300TA Manuel utilisateur

VOLTCRAFT

VOLTCRAFT IC-100HD Manuel utilisateur

RIDGID

RIDGID micro CA-25 Manuel utilisateur