Weller MG130 Manuel utilisateur

OPERATING MANUAL

Version 1

8. Warranty

General conditions according to ORGALIME S 2000.

Warranty: 2 years (except for lters). The time is measured from date of invoice.

Always contact the supplier before returning a product.

The invoice has to be shown at the time of the complaint.

Content

1. Introduction 2

Safety instructions

Put into operation

Troubleshooting

Maintenance and service

Technical data

Article numbers

Warranty

1. Introduction

Filter system designed to catch and eliminate hazardous gases and particles in different

applications like soldering, gluing, solvents etc.

6. Technical data

Width x height x depth 456 x 496 x 200 mm

Weight 12 kg

Sound level at 1 meter > 52 dB(A)

Voltage 100/240 V

Effect 100 watt

Glass tube fuse 2 x 6,3 AT, 250 V

Maximum suction capacity 100 m3/h

Blower capacity 140 m3/h

Micro lter HEPA class H13, Separation degree, MPPS >99,95 %

Gas lter - Separation degree >95 %

Pre lter F7

Filter minitoring system Yes

Warranty (excl. lter) 2 years

ESD approval, SP Dno 230-05-0189

CE-guidelines 73/23, 89/336, 89/392, 91/368,

92/31, 93/44, 93/68

RoHS Yes

7. Article numbers

Filter system MG130 130-1055-ESD

Main lter 130-2000-ESD

Pre lter (5 pcs) 130-2010

2. Safety instructions

The unit must not be exposed to temperatures exceeding 50° C, open ames or conden-

sated solvents.

Switch off the lter unit when changing lter.

3. Put into operation

The best possible gas ltration will be achieved if:

- Process air temperature in the gas lter < 38 °C

- Relative humidity < 60 %

- Gas molecules > 30 g / mol (ltration better with larger molecules)

- Boiling temperature of gas molecules > 0 °C

NOTE! The unit may dust some from the main lter after transportation.

Make sure the starting of the lter system is made in an appropriate room.

The suction capacity can be adjusted in three steps by pressing the reset button at the

control panel repeatedly.

5. Maintenance and service

Exchange of pre lter:

1. Swith off the lter system.

2. Open the locks (A) and remove the

lid (B).

3. Replace the pre lter.

4. Put the top (B) and the locks (A)

back.

Exchange of main lter:

1. Swith off the lter system.

2. Open the locks (A) and remove the

lid (B).

3. Pull the main lter straight up.

4. NOTE! Mark the new lter with the

date of change.

5. Assemble the new lter. Make sure

that the inlet to the fan ts to the

connection in the bottom of

the lter.

6. Put the top (B) and the locks (A)

back.

4. Troubleshooting

Do not modify the lter unit.

- If the lter unit is out of order, please check:

- the electricity supply is connected in a correct way.

- the fuse is whole.

- If alarm sounds when starting and red indicator ashes:

Recommended lter lifetime is exceeded. Indicates exchange of main lter. Restore the

alarm with the reset button on the control panel and plan for lter exchange. See ”Exchange

of main lter” under headline 6 ”Maintenance and service”.

- If alarm sounds when starting and red indicator is lighted:

Suction capacity is low. Restore the alarm with the reset button on the control panel and

switch off the lter unit. Check nozzles and tubes, clean if necessary. If the alarm comes back

when starting, the lter is used and must be changed. See ”Exchange of main lter”under headline

6 ”Maintenance and service”. If no action is taken, the lter unit stops after ve minutes to protect

from overheating.

The main lter should be changed at least once a year to guarantee the separation degree

on gases.

To guarantee a satisfactory function, clean the nozzles and the extraction arms regu-

larly.

When changing the main lter, the lter time is set to zero by keeping the reset button pressed

and turning the switch on at the same time.

NOTE! The reset button must be pressed until the red light-emitting diode acknowledge the

order.

Table des matières

Autres manuels Weller pistolet à souder

Weller

Weller WXP?65 Manuel utilisateur

Weller

Weller LR 21 Manuel utilisateur

Weller

Weller WMA 3V Manuel utilisateur

Weller

Weller KHE 81 Manuel utilisateur

Weller

Weller WT 1 Manuel utilisateur

Weller

Weller WLC100 Manuel utilisateur

Weller

Weller WXPP Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

Weller

Weller WSD 151 Manuel utilisateur

Weller

Weller ML500MP Manuel utilisateur

Weller

Weller WD1 Manuel utilisateur

Weller

Weller WTP 90 Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

Weller

Weller wd 2 Manuel utilisateur

Weller

Weller T0052921399N Manuel utilisateur

Weller

Weller WLC200 Manuel utilisateur

Weller

Weller WE 1 Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

Weller

Weller WHA 3000P Manuel utilisateur

Weller

Weller BP860MP Manuel utilisateur

Weller

Weller WR 2 Manuel utilisateur

Weller

Weller WPS18MP Pro Series Manuel utilisateur

Weller

Weller WAD 101 Manuel utilisateur

Weller

Weller WSD 151 Manuel utilisateur

Manuels pistolet à souder populaires d'autres marques

Bakon

Bakon 3200 Manuel utilisateur

Proxxon

Proxxon Gaslotset MGS Manuel utilisateur

jbc

jbc SFR-A Manuel utilisateur

jbc

jbc CL8010 Manuel utilisateur

HAKO

HAKO FX-8804 Manuel utilisateur

SATA

SATA 02002A Manuel utilisateur

Velleman

Velleman HRJA151 Manuel utilisateur

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instructions de montage

ersa

ersa i-CON 1V Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-100 Manuel utilisateur

AlienTek

AlienTek T100 Manuel utilisateur

Atten

Atten ATETOOL AT-689A Manuel utilisateur

Surtek

Surtek 112554 Dimensions et guide d'installation

Parkside

Parkside PLBS 30 A1 Manuel utilisateur

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manuel utilisateur

multicomp pro

multicomp pro MP740893 Manuel utilisateur

Atten

Atten ST-2090D Manuel utilisateur

RIDGID

RIDGID RT-100 Manuel utilisateur