WEG CFW300 Manuel utilisateur
WEG Electric Corp.
WEG Automation Technical Note: CFW300
Page: 1 / 4
WEG Electric Corp. – Integrated Solutions Center
6655 Sugarloaf Parkway, Duluth, GA 30097 – www.weg.net/us
Basic Functionality Review with Speed Potentiometer and Run Forward/Stop/Run
Reverse Control Setup
The following parameters and values will be used for this tech note:
P204=5 Factory Reset to 60hz
P401=3.2A Motor Rated Current s
P402=1725 Motor Rated Speed
P403=60 Hz Motor Rated Freq
P100=2.0s Acceleration
P101=2.0s Deceleration
P133=3 Hz Drive Min Speed
P134=60Hz Drive Max Speed
P002 (Read) Drive Frequency
P003 (Read) Motor Current
P207=18 Bar Graph; AI 1 input value
P220 = 1; LOC/REM Source Selection; Always Remote
P222 = 1 REM Reference Selection; AI1 (Default)
P226 = 4; DIx (Default)
P227 = 1; Selection of Remote run-stop; DIx. (Default)
P231 = 0; AI1 Signal Function; Speed Reference. (Default)
P233 = 0; AI1 0-10V. (Default)
P263= 4 Function for DI1; ForwardRUN
P264 = 5 Function for DI2; Reverse RUN
P271 = DIx Function; All DIx NPN. . (Default)
Steps 2 thru 5 will use the motor’s nameplate to find the CFW300’s motor’s related parameters.
To begin reset the drive to factory defaults:
1. Press the "P" button to get to the parameters, and scroll with UP/DOWN arrow to parameter
204(Reset Defaults). Press "P" again,then using the UP/DOWN arrows scroll tovalue "5". Press
“P” to accept the value. This will reset the drive parameters to factory default for 60 Hertz.
2. Scroll UP/DOWN to Parameter 400, Motor Rated Voltage. Press “P”. Scroll UP/DOWN to select
the motor name plate voltage. Press "P" to accept the value.
WEG Electric Corp.
WEG Automation Technical Note: CFW300
Page: 2 / 4
WEG Electric Corp. – Integrated Solutions Center
6655 Sugarloaf Parkway, Duluth, GA 30097 – www.weg.net/us
3. Scroll UP/DOWN to Parameter 401, Motor Rated Current. Press “P”. Scroll UP/DOWN to select
the motor name plate FLA. Press "P" to accept the value.
4. Scroll UP/DOWN to Parameter 402, Motor Rated Speed. Select “P”. Using the UP/DOWN arrows
select the motor nameplate RPM. Once found press “P” again to save the value.
5. Scroll UP/DOWN arrows to Parameter 403, Motor Max Frequency. Using the UP/DOWN arrows
select the motor nameplate frequency. Once found press “P” again to save the value. The
following steps will set up the accel/decel time along with the min/max speed which the VFD
will react to when the speed pot or the CFW300 HMI’s UP/DOWN arrows is adjusted.
6. Scroll UP/DOWN arrow to find Parameter P100, Acceleration. Select "P". Use the UP/DOWN
arrow to find 5.0 seconds (for this exercise) and press "P" to accept the value.
7. Scroll UP/DOWN arrow to find Parameter P101, Deceleration. Select "P". Use the UP/DOWN
arrow to find 5.0 seconds (for this exercise) and press "P" to accept the value.
8. Scroll UP/DOWN to Parameter P133, MIN Speed. Select “P”. Use the UP/DOWN arrow tofind
3.0 (for this exercise). Press "P" to accept the value.
9. Scroll UP/DOWN to Parameter, P134,MAX Speed. Select "P". Use the UP/DOWN arrow to find
60.0 Hertz (for this exercise). Press "P" to accept the value.
10. Scroll UP/DOWN to Parameter P002,VFD Output Frequency. Now press the Run/Stop key to
start the motor. Since the drive speed is 3hz, the drive outputwill be 3. Now use the UP arrow
and increase the value, and the motor will speed up. Once this is verified, press the Run/Stop
key and the motor will stop.
Next analog control. Use the drawing below as reference for NPN:
WEG Electric Corp.
WEG Automation Technical Note: CFW300
Page: 3 / 4
WEG Electric Corp. – Integrated Solutions Center
6655 Sugarloaf Parkway, Duluth, GA 30097 – www.weg.net/us
The following steps will set up the “REMOTE” operation of the VFD (potentiometer or analog
voltage/milliamp signal for the speed source thru the CFW300’s Analog Connections,as well as
Run/Stopand Direction thru theVFD’sDigital Inputs).
1. Scroll UP/DOWN toparameter P220,"LOC/REM Source Selection". Press "P",scroll UP/DOWN
to find 1, "Always Remote". Press "P" to accept the value.
2. ScrollUP/DOWN to parameter P222, "REM Reference Selection". Press "P". Scroll
UP/DOWN to 1, "AI1" (Analog Input 1). Press "P" to accept the value.
3. For speed reference from potentiometer, the VFD will provide 10VDC. Connect the outside
wires (POT reference connections) to terminals (-)7 and (+)9, and the center wire (POT wiper
input) to terminal 8.
4. Scroll UP/DOWN toparameter P231,"AI1 Signal Function".Press "P",scroll UP/DOWN to find 0,
"Speed Reference". Press "P" to accept the value.
5. Scroll UP/DOWN to parameter P233, "AI1 Input Signal". Press "P", scroll UP/DOWN to find 0, "0
to 10V/20 mA". Press "P" to accept the value.
6. To verify the AI1 signal “polarity” is correct, scroll UP/DOWN to parameter P207, "Bar Graph
Parameter". Scroll UP/DOWN to "18". Press "P" to accept the value (this value refers to P018,
which is the AI 1 value). This will verify the signal connections are correct using the bar graph on
the display. Wire connection signal will display as they are connected on the bar graph at the
very bottom of the display. Scroll UP/DOWN and if the POT signal displays in reverse of the
UP/DOWN arrows, then swap wires on terminals 7 and 9.
WEG Electric Corp.
WEG Automation Technical Note: CFW300
Page: 4 / 4
WEG Electric Corp. – Integrated Solutions Center
6655 Sugarloaf Parkway, Duluth, GA 30097 – www.weg.net/us
Setup Run/Stop and Direction control: In this setup, DI1 will be "Forward RUN" (Maintained N.O. dry
contact) and DI2 will be "Reverse RUN" (Maintained N.O. Dry Contact). Only one signal can be made at
a time, and breaking both signals will be STOP. This is normally accomplished with a 3-position
maintained selector switch. Position 1=FWD RUN (DI1), 2=OFF, and 3=REVERSE RUN (DI2). Center
position is not associated or connected to an input so it =STOP.
1. Press “P” and scroll UP/DOWN to parameter 271, "DIx Function". Press "P", scroll UP/DOWN to
find 0, "All DIx NPN". Press "P" to accept the value.
2. Scroll UP/DOWN to parameter 220, "LOC/REM Selection Source". Press "P". Scroll UP/DOWN to
find 1, ”Always Remote”. Press "P" to accept the value.
3. Scroll UP/DOWN to parameter 226, "REMFWD/REV". Press "P". Scroll UP/DOWN to find 4,
”DIx”. Press "P" to accept the value.
4. Scroll UP/DOWN to parameter 227, "REM Run/Stop Selection". Press "P". Scroll UP/DOWN to
find 1,for "DIx" (meaning oneof the Digital Inputs). Press"P"to accept the value.
5. Scroll UP/DOWN to parameter 263, "DI 1Input Function". Press "P". Scroll UP/DOWN to find
“4”,for "Forward Run". Press "P" toaccept the value.
6. Scroll UP/DOWN to parameter 264"DI 2 InputFunction". Press "P". Scroll UP/DOWN tofind “5”,
"Reverse Run". Press "P" to accept the value.
Autres manuels pour CFW300
2
Table des matières
Autres manuels WEG Onduleur
WEG
WEG CFW100 series Guide rapide
WEG
WEG CVW300G2 Manuel utilisateur
WEG
WEG CFW-11 Series Manuel utilisateur
WEG
WEG bacnet CFW701 Manuel utilisateur
WEG
WEG Easy Drive CFW10 Manuel utilisateur
WEG
WEG CFW-11 Series Manuel utilisateur
WEG
WEG bacnet CFW701 Manuel utilisateur
WEG
WEG CFW100 series Manuel utilisateur
WEG
WEG CFW-11 Series Instructions d'utilisation
WEG
WEG MVW3000 Series Manuel du propriétaire
WEG
WEG CFW-09 Manuel utilisateur
WEG
WEG CFW-09 Manuel utilisateur
WEG
WEG CFW-11W G2 RB Series Manuel utilisateur
WEG
WEG CFW501 V1.8X Manuel du propriétaire
WEG
WEG bacnet CFW701 Mode d'emploi
WEG
WEG CFW-11 Series Manuel utilisateur
WEG
WEG DeviceNet CFW500 Mode d'emploi
WEG
WEG CFW08 Vector inverter Manuel utilisateur
WEG
WEG CFW100 series Manuel utilisateur
WEG
WEG AG10 Series Manuel utilisateur
