Weber mt CR 5 Guide de configuration
SERVICE - INFORMATION
Section 6*** Page 1
Service Information 2003
Repair Instructions CR 5 - CR 6
SERVICE - INFORMATION
Section 6*** Page 2
Service-Information 2003
Repair Instructions CR 5 - CR 6
Preface .......................................................................................................3
Illustration ..................................................................................................4
1. Disassembly .....................................................................................5
2. Reassembly ....................................................................................15
Table of Contents
SERVICE - INFORMATION
Section 6*** Page 3
Service Information 2003
Repair Instructions CR 5 - CR 6
Indicates important information and hints which must be followed by the operator and service personnel.
Indicates working and operating methods requiring in addition the observance of all applicable
environment protection and waste disposal regulations.
Indicates working and operating methods which must be precisely followed in order to prevent the soil
compactor from being damaged or deteriorated.
Indicates working and operating methods which must be precisely followed in order to avert direct danger
to persons.
Preface
Before starting your repair work, carefully read these repair instructions. Carefully follow all instructions and always
carry out the described operations in the indicated order.
The safety precautions prescribed for repair work must be followed in order to avert injury to persons and/or damage
to material property.
For safety reasons, any modifications and retrofittings made on the soil compactor without the manufacturer's
authorization are prohibited. Damage resulting from modifications or retrofittings is excluded from the manufacturer's
liability. Only use genuine WEBER spare parts to ensure a safe and reliable operation.
Important information is highlighted by the pictograms explained in the following. Please strictly observe the
information given in the repair instructions.
SERVICE - INFORMATION
Section 6*** Page 4
Service-Information 2003
Repair Instructions CR 5 - CR 6
SERVICE - INFORMATION
Section 6*** Page 5
Service Information 2003
Repair Instructions CR 5 - CR 6
Figure 3
Figure 2
1. Demontage
1
2
1
2
1
2
Remove the fastening screw (1/1) of the V-belt pulley
(1/2).
Screw 2 hexagon head cap screws (4/1) into the V-belt
pulley (4/2).
Press the V-belt pulley(3/1) from the eccentric shaft (3/2).
Figure 1
SERVICE - INFORMATION
Section 6*** Page 6
Service-Information 2003
Repair Instructions CR 5 - CR 6
Figure 5
Figure 6
Figure 4
2
1
1
2
1
2
Remove the fastening screw (4/2) of the cover (4/1).
Screw the hexagon head cap screws (5/1) into the cover
(5/2) and press the cover from the housing.
Remove the fastening screw (6/1) of the cover (6/2).
SERVICE - INFORMATION
Section 6*** Page 7
Service Information 2003
Repair Instructions CR 5 - CR 6
Figure 7
Figure 8
Figure 9
1
1
1
2
Screw the hexagon head cap screws (7/1) into the cover
(7/2) and press the cover from the housing.
2
Remove the shims (8/1).
Remove the vent screw (9/1) of the cylinder cover (9/2).
SERVICE - INFORMATION
Section 6*** Page 8
Service-Information 2003
Repair Instructions CR 5 - CR 6
Figure 10
Figure 11
Figure 12
2
1
1
2
1
Lossen the fastening screws (10/1) of the cylinder
cover (10/2).
Screw the hexagon head cap screw (11/1) into the
fixing flange of the cylinder cover and press the cylinder
cover out of the vibrator housing.
Remove the fastening screw (12/1) of the cover (12/2).
SERVICE - INFORMATION
Section 6*** Page 9
Service Information 2003
Repair Instructions CR 5 - CR 6
Figure 13
Figure 14
Figure 15
1
1
1
Screw the hexagon head cap screws (13/1) into the cover
(13/2) and press the cover from the housing.
2
Remove the shims (14/1).
Dismantle the eccentric (15/1) of the fixed eccentric
shaft.
Risk of injury because eccentric may overturn.
SERVICE - INFORMATION
Section 6*** Page 10
Service-Information 2003
Repair Instructions CR 5 - CR 6
Figure 16
Figure 17
Figure 18
1
1
1
Remove the eccentric (16/1) of the variable eccentric
shaft.
Risk of injury because eccentric may overturn.
Put the assembly sleeve (17/1) on the eccentric shaft
and beat the shaft into the housing.
Risk of injury because vibrator housing may
slide or overturn.
Take the eccentric (18/1) out of the housing.
Autres manuels pour CR 5
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Weber mt Pilonneuse et bourreuse vibrante
Weber mt
Weber mt SRE 590 DC Mode d'emploi
Weber mt
Weber mt CF 1-II Hd Mode d'emploi
Weber mt
Weber mt SRV 590 Mode d'emploi
Weber mt
Weber mt CR 9-II CCD 2.0 Mode d'emploi
Weber mt
Weber mt CF 1-II Hd Mode d'emploi
Weber mt
Weber mt SRV 660 Mode d'emploi
Weber mt
Weber mt SRV 300 Mode d'emploi
Weber mt
Weber mt CF 2 Instructions d'utilisation et d'installation
Weber mt
Weber mt CR 9-II MDM Mode d'emploi
Weber mt
Weber mt SRV 650 Mode d'emploi
Weber mt
Weber mt CR 2 Hd Mode d'emploi
Weber mt
Weber mt SRV 590-II Mode d'emploi
Weber mt
Weber mt SRV 660 Mode d'emploi
Weber mt
Weber mt CF 1 HD Mode d'emploi
Weber mt
Weber mt SRV 300-II Mode d'emploi
Weber mt
Weber mt CR 2 Mode d'emploi
Weber mt
Weber mt SRV 660-II Mode d'emploi
Weber mt
Weber mt CR 3-II E Mode d'emploi
Weber mt
Weber mt SRE 300 Mode d'emploi
Weber mt
Weber mt CR 2 R Mode d'emploi
