Webb WER18SP Manuel utilisateur

OPERATOR’S MANUAL AND PARTS LIST

SELF PROPELLED PETROL LAWNMOWER

WER18SP

Spares & Support: 01793 333212

www.webblawnmowers.co.uk

Before use please read & understand this manual, paying particular attention to

the safety instructions.

16/06/2014

Thank you for choosing our petrol lawnmower.

To ensure that you get the best results from your petrol lawnmower please read all of these safety and

operating instructions carefully before using this product.

TABLE OF CONTENTS PRODUCT SPECIFICATION

Product Specifications…………………….1

Safety Rules……………………………..1-3 Model number WER18SP (193803001)

Assembly/Pre-Operation………………...3-5 Petrol engine B&S450eseries125cc

Operation………………………………...6-8 Engine speed 2800rpm

Maintenance……………………………...8-9 Cutting width 457mm

Storage………………………………………9 Adjustable cutting height 15-65mm

Environment…………………….………….10 Grass collection capacity 60L

Symbols…………………………………….10 Steel deck

Parts Diagram and Lists...………………11-16 Sound Pressure Level 80.5 dB(A)

DOC………………………………………..17 Guaranteed Sound Power Level 96dB(A)

Also Available From Webb…………….......18 Max. vibration value 6.360m/ s2

IMPORTANT: Failure to observe the following safety instructions could result in serious injury.

WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making

repairs, always the disconnect the spark plug lead.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after

engine has stopped. To avoid severe burns on contact, stay away from these areas.

Drive lever

Brake lever

Grass catcher

Height adjust handle Quick fix handle

B&S 450E series

Water nozzle

1. GENERAL OPERATION AND SAFETY RULES

zRead the instructions carefully. Be familiar with the controls and the proper use of the equipment.

zDo not put your hands or feet near or under rotating parts. Keep clear of the discharge opening at all

times.

zOnly allow responsible individuals, who are familiar with the instructions, to operate the machine.

zThoroughly inspect the area where equipment is to be used and remove all objects, which could be

thrown by the machine.

zNever mow while people, especially children, or pets are nearby.

zWhile mowing, always wear appropriate footwear and trousers. Do not operate the equipment when

barefoot or wearing open sandals.

zDo not pull the mower backwards unless absolutely necessary.

zNever operate the lawnmower with defective guards, or without safety devices, for example

deflectors and/or grass catchers, in place.

zOnly use accessories approved by the manufacturer.

zStop the blade(s) when crossing gravel drives, paths, or roads.

zStop the engine and disconnect the spark plug:

-before clearing blockages or unclogging the chute.

-before checking, cleaning or working on the lawnmower.

-after striking a foreign object. Inspect the lawnmower for damage and make repairs before

restarting and operating the lawnmower.

-if lawnmower starts to vibrate abnormally (check immediately).

zShut the engine off and wait until it has come to a complete stop before removing the grass catcher.

zMow only in daylight or good artificial light.

zDo not operate the machine while under the influence of alcohol or drugs.

zNever operate machine in wet grass, this could cause slipping.

zKeep a firm hold on the handle and walk; never run.

zDisengage the self-propelled mechanism before starting the engine.

zAlways wear safety goggles or safety glasses with side shields when operating the mower.

zRemove obstacles such as rocks, tree limbs, etc.

zWatch for holes, ruts, or bumps. Tall grass can hide obstacles.

zDo not trim near drop-offs, ditches or embankments. The operator could lose their footing or balance.

zDo not mow excessively steep slopes.

zKeep in mind that the operator or user is responsible for accidents or hazards involving the machine

that could occur to other people or their property.

zBe alert and turn the machine off if children enter the area.

zFor wheeled rotary machines, mow across the face of slopes, never up and down.

zNever allow children or people unfamiliar with these instructions to use the lawnmower.

zWARNING-Petrol is highly flammable.

-store fuel in containers specifically designed for this purpose;

-refuel outdoors only and do not smoke while refueling;

-add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the

engine is running or when the engine is hot;

-if petrol is spilled, do not attempt to start the engine but move the machine away from the area

of spillage and avoid creating any source of ignition until the petrol vapours have dissipated;

-replace fuel tanks and container caps securely.

zBefore using, always visually inspect to ensure that the blade, blade bolts and cutter assembly are not

worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.

zNever tamper with safety devices. Regularly check that they are operating properly.

zKeep the machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow the

machine to cool before storing.

zExercise extreme caution when changing direction on slopes.

zNever attempt to make wheel height adjustments while the engine is running.

zGrass catcher components are subject to wear, damage, and deterioration, which could expose

moving parts or allow objects to be thrown. Frequently check components and replace with the

manufacturer’s recommended parts, when necessary.

zThe mower blades are extremely sharp. Wrap the blade, wear gloves, and use extra caution when

servicing them.

zDo not change the engine governor setting or over-rev the engine.

zStop the engine if the lawnmower has to be tilted for transportation when crossing surfaces other than

grass, and when transporting the lawnmower to and from the area to be mowed.

zDisengage the drive clutch before starting the engine.

zStart the engine carefully according to the instructions, with your feet well away from the blade.

zDo not tilt the lawnmower when starting the engine or cutting.

zDo not start the engine when standing in front of the discharge chute.

zNever pick up or carry a lawnmower while the engine is running.

ASSEMBLY/PRE-OPERATION

Read this instruction manual in its entirety before you assemble or operate your new lawnmower.

IMPORTANT: The lawnmower is shipped WITHOUT OIL OR PETROL in the engine.

Your new lawnmower has been assembled and tested at the factory.

Roll the lawnmower out of the carton and check the carton thoroughly for additional loose parts.

To avoid damage during the transport process, the drive and brake cables for your machine may not be

fitted to their appropriate handle bar.

The front cable is the brake cable, which is to be fitted to the front lever on your machine, this is the

Operator Presence Control Lever (OPC). The cable at the rear is your drive cable, which is to be fitted to

the rear lever, which is your Drive Lever.

Brake Cable

Drive Cable

Apply inward pressure to the lever assembly on the left hand side of the machine, to remove the lever lug

from the handle assembly.

Insert the Brake Cable into the OPC Lever.

Insert the Drive Cable into the Drive Lever.

Re-seat the lever assembly back into the main handle.

INSTALLATTACHMENTS

Your lawnmower was shipped ready to be used as a rear bag mower.

The mower has three different operating modes.

1. Collecting:

• Fit the grassbox by lifting the rear flap on the mower and hook the front of the box to the shaft on the

mower.

• Lower the flap to lock the grassbox in position.

• When the box is full, the grass will be visible through the viewing window in the top of the box.

• Stop the engine before emptying the grassbox.

2. Rear Discharge:

• With the grassbox removed and the rear flap in the down position, the mower will cut and discharge the

grass from the rear of the machine.

3. Mulching:

• Fit the mulch plug to the rear discharge opening of the mower and close the rear flap.

• The mower will now recycle the chopped grass into the lawn surface.

• To mulch efficiently only cut one third of the length of the grass.

SETUPYOURMOWER

IMPORTANT: Unfold the handle carefully so

as not to pinch or damage the control cables.

1. Depress the Operator Presence Control Bar

(OPC) and raise the handles until the lower handle

section locks into place at the mowing position.

2. With the Operator Presence Control Bar still

depressed raise the upper handle section into place

on the lower handle and tighten both handle knobs.

OPERATION

Operator Presence Control (OPC) Bar - must be held down to the handle to start the engine. Release to

stop the engine.

Starter rope - used to start the engine.

Drive control lever - used to engage self- propelled motion of the lawn mower.

LAWNMOWER ENGINE SPEED

The engine speed was set at the factory for optimum performance. Speed is not adjustable.

DRIVE CONTROL (Model: WER18SP)

zThe drive is controlled by holding the Operator Presence Control bar down to the handle and pulling

the drive control lever back towards the handle.

zForward motion will stop when the operator presence control bar is released. To stop forward motion

without stopping the engine release the drive control lever until the drive control disengages and hold the

operator presence control bar down against handle to continue mowing without the drive.

ADJUST CUTTING HEIGHT

Lower the cutting deck for a low cut and raise the deck for a high cut; adjust cutting height to suit your

requirements. Medium position is best for most lawns.

BEFORE STARTING ENGINEADD OIL

Before each subsequent use the oil level must be checked and if necessary topped up with SAE30 engine

oil.

OIL FILLER CAP/DIPSTICK

Your lawnmower is shipped without oil in the engine.

CAUTION: DO NOT overfill the engine with oil, or it will smoke heavily from the muffler on startup.

1. Be sure that the lawnmower is on level ground.

2. Remove the oil dipstick from the oil fill spout.

3. Insert and tighten the dipstick.

IMPORTANT:

zCheck the oil level before each use.Add oil if needed. Fill to the full line on the dipstick.

zChange the oil after every 25 hours of operation or each season. You may need to change the oil

more often under dusty, dirty conditions. See “TO CHANGE ENGINE OIL” in the Maintenance

section of this manual.

ADD PETROL

zFill fuel tank to the bottom of the tank filler neck. Do not overfill. Use fresh, clean, regular unleaded

petrol. Do not mix oil with petrol. Purchase fuel in quantities that can be used within 30 days to

assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use petrol near an open flame.

FUEL TANK CAP

UPPER LIMIT

LOWER LIMIT

CAUTION: To avoid engine problems, the fuel system should be emptied before being stored for 30 days

or more. Empty the fuel tank, start the engine and let it run until the fuel lines and carburettor are empty.

Use fresh fuel for your next use of the machine. See Storage Instructions for additional information.

Never use engine or carburettor cleaner products in the fuel tank or permanent damage may occur.

START ENGINE

To start the engine, first make sure that the spark plug is tightened and that the machine is filled with

sufficient oil and petrol.

NOTE: Due to the protective coating on the engine, a small amount of smoke may be present during the

initial use of the product and should be considered normal.

Press the primer bulb 3 times to allow fuel into the engine (for the first use, press 5 times).

Hold the Operator Presence Control bar down to the handle and pull the starter handle quickly.

Do not allow the starter rope to snap back.

STOP ENGINE

zTo stop engine, release the Operator Presence Control bar.

zDisconnect the spark plug cap if the lawnmower is to be left unattended.

MOWING TIPS

zUnder certain conditions, such as very tall grass, it may be necessary to raise the height of the cut to

reduce the pushing effort and to keep from overloading the engine and leaving clumps of grass

clippings. It may also be necessary to reduce ground speed and/or run the lawnmower over the area a

second time.

zFor extremely heavy cutting, reduce the width of cut by overlapping the previously cut area and mow

slowly.

zPores in cloth grass catchers can become filled with dirt and dust during use and catchers will collect

less grass. To prevent this, regularly hose the catcher off with water and let it dry before using.

zKeep the top of the engine around the starter clean and clear of grass clippings and chaff. This will

assist engine air flow and extend engine life.

MAINTENANCE

IMPORTANT-Regular, careful maintenance is essential for keeping the safety level and original

performance of the machine unchanged over time.

1) Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. Regular

maintenance is essential for safety and performance.

2) Never store the equipment with fuel in the tank inside a building where vapour may reach a flame,

spark or source of extreme heat.

3) Allow the engine to cool before storing in an enclosed space.

4) To reduce the fire hazard, keep the engine, exhaust silencer, battery compartment and fuel storage area

free of grass, leaves, or excessive grease. Remove grass cuttings from containers before storage.

5) Do not use equipment with worn or damaged parts. Parts should be replaced not repaired. Only use

genuine spare parts. Parts that are not of the same quality can damage the equipment and create safety

hazards.

6) If the fuel tank has to be drained, this should be done outdoors and when the engine is cool.

7) Wear strong work gloves when removing and reassembling the blade.

8) Check the blade’s balance after sharpening.

9) Check the self-closing guard and grass-catcher frequently for wear and deterioration.

10) Whenever the machine is to be handled, transported or tilted you must:

- Wear strong working gloves.

- Grasp the machine at the points that offer a safe grip, clear of the blade and taking account of the weight

of the machine and its distribution.

CLEANING

Your lawnmower has been supplied with a hose pipe connector towards the back of the deck. This enables

you to clean your machine, using your garden hose. Clip the hose to the machine using a standard hose

connector. Turn on your tap. Ensure that any trailing hose is away from the machine deck. Start the

machine. The momentum of the blade rotation will force water around the deck to clean it.

Carefully clean the machine after each cut to ensure an easy start-up next time you use the machine. Be

sure to remove grass debris and mud accumulated inside the chassis before it dries.

If you need to tilt the mower while cleaning always tip it backwards towards the handles, do not tip it on

its side as this will cause oil to enter the carburettor or exhaust.

The paintwork on the inside of the chassis may peel off over time due to the abrasive action of the cut

grass; when this occurs you must touch up the paintwork using a rustproof paint as soon as possible to

prevent the formation of rust that would lead to corrosion of the metal.

Remove the transmission casing by removing the screws and clean around the transmission and drive

belts with a brush or compressed air once or twice a year.

Once every season, the drive wheels should be cleaned internally. Remove both wheels. Clean the gear

wheel and the wheel gear rim of grass and dirt using a brush or compressed air.

CHANGING BLADES

Empty the oil tank before removing the blade.

To replace the blade, undo the screw.

Reinstall as illustrated. Tighten the screw properly. Tightening torque 45 Nm.

When replacing the blade, the blade screw should also be replaced.

STORAGE

The same petrol must not remain in the tank for more than one month.

Thoroughly clean the mower and store it indoors in a dry place.

Table des matières

Autres manuels Webb Tondeuse à gazon

Webb

Webb WERR17P Manuel d'installation et d'exploitation

Webb

Webb WERR19SP Manuel d'installation et d'exploitation

Webb

Webb WERR17P Manuel utilisateur

Webb

Webb WEH18 Manuel utilisateur

Webb

Webb WER21HW Manuel utilisateur

Webb

Webb WEH12R Manuel d'installation et d'exploitation

Webb

Webb WER21HW4 Manuel utilisateur

Webb

Webb WEER36 Manuel utilisateur

Webb

Webb WEER38 Manuel utilisateur

Webb

Webb 12530 Manuel utilisateur

Webb

Webb WER18HP Manuel utilisateur

Webb

Webb C14L Manuel utilisateur

Webb

Webb WER18HP Instructions d'installation et d'entretien

Webb

Webb WERR17LIP Manuel d'installation et d'exploitation

Webb

Webb WERR16 Instructions d'installation et d'entretien

Webb

Webb WEER40 Manuel utilisateur

Webb

Webb WEER33 Manuel d'installation et d'exploitation

Webb

Webb WEER36 Manuel utilisateur

Webb

Webb Werr17 Instructions d'installation et d'entretien

Webb

Webb WER40HP Manuel utilisateur

Webb

Webb WER16LIHP Manuel d'installation et d'exploitation

Webb

Webb WER40HPSFX Manuel utilisateur

Webb

Webb WER21HW Manuel utilisateur

Webb

Webb WER46SP Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur