Webasto Blue Cool Classic Manuel utilisateur

Operation Manual

WEBASTO BLUE COOL CLASSIC

Compact Air Condition Systems

General Information

Dear Webasto Customer!

This operation manual provides an overview about how to use the compact air condition system

and its control panel. An extensive documentation and description can be found in the installation

and service manual.

Safety Notes

In general, all A/C systems are running on 230 Volt AC. For all work at any of the components like

pumps, compressor, blowers or electronics, the power connection has to be interrupted. All work

at the electric wiring must be performed by specialized installers.

Before starting the air-condition system, check the following points:

•The closing valve at the sea-cock is open!

•The sea-water strainer is clean and filled with water!

•The boat has enough water under the body and the sea-cock is not blocked!

•All supply and return air grilles are open and not blocked by luggage, clothing or anything else!

•After switching on, water comes out of the over-board discharge. If not, switch off the system

and check the sea-water circuit again!

The control panel „Air-Control“ for Compact Systems

The digital control panel is always factory pre-programmed and the secondary commands are

code-protected.

•If your Compact air-condition system has a heat cycle (easily detectable by the magnetic valve

next to the compressor), the cabin(s) can be heated until a sea-water temperature of about

10°C. The control panel will be pre-set with the function „Automatic“.

•If your air-condition does not have a heat cycle, the function „Cooling“ is pre-set.

On/Off

Heat Cycle

Mode

Automatic Mode

Cool Cycle

Mode Read-out

(0)

Higher

Values

(Sun)

Function

(F) Lower

Values

(

Snow flake

)

Blower Speed

Operating the Air-Control for Compact Systems

When the air-conditioning is connected with the electrical power, the system initialises itself. The

display shows Init and afterwards the frequency, e.g. 50 Hz.

Starting Press once the button.

On is displayed and after appr. 20 sec. the current room temperature, e.g.

28.5 (°C) is shown. Depending on the room and set-point temperature the

appropriate mode will start. Mode indication by LED.

→A malfunction is indicated by a blinking error code (see below)

→ba11 is no error code that causes a system stop (see below)

Setting the

Temperature With the buttons and between 15°C and 29°C while the room -

temperature is displayed.

Air-condition without heat cycle

→the set temperature must be below the room temperature.

e.g. room temperature 25° C

Set temperature between 15°C and 24°C.

•Air-condition with heat cycle

→the set temperature can be between 15°C and 29°C.

e.g. room temperature 25° C

Set temperature = 20°C, Cool mode starts.

Set temperature = 29°C, Heat mode starts.

Setting Blower

Speed Press the button until bis shown to the left and the selected value to

the right, e.g. b 5 (Blower speed 5)

•Value Range (Blower speeds): 1-2-3-4-5 and A

•Factory Setting: A(Automatic Blower Speed)

Program with the buttons and . Confirm by pressing the button.

Secure your setting by pressing the button. The display shows memo

and then the room-temperature.

→In the automatic blower speed mode (b A) the blower start and

operation depends on the temperature. If there is no need for blower

operation, the display shows ba11. It can take some time before the blower

starts.

→The manual blower speed mode (1 to 5) is indicated by the LED

„Manual blower operation“.

Displaying the

Evaporator

Temperature

Press the button until Eis shown to the left and a numerical value to

the right, e.g. E10.5. Check if the current operation mode is functioning

properly.

→Cool mode (LED snow flake) = Evaporator temperature drops constantly

→Heat mode (LED sun) = Evaporator temperature rises constantly.

Access to further

program levels Press the button until code is displayed. With a special access code

specific settings can be modified (by the installer).

Further information can be found in the installation manual.

Error code display and actions

The error codes are viewed on the display screen. After the error codes are displayed, the system

is shut off for 60 sec. and re-started (except for ba11). If the same error occurs within 30 minutes,

the A/C system will be completely stopped. In this case, it can only start again if the error has

been solved and the system has been completely switched off and on again.

Error codes and causes

AAA Persistent low voltage (below 195 Volt for more than 5 sec.)

A01 Low pressure cut-out compressor 1

→Not enough refrigerant in the system, please inform service station.

→Sea water temperature in heat mode too low (<7°C), heat mode not

possible.

A02 High pressure cut-out compressor 1

→Sea water circuit interrupted, please check circuit.

→Too much refrigerant in system, please call service station.

→Sea water temperature in heat mode too high (>17°C), heat mode not

possible.

A03 - 08 Not applicable for “Classic” systems

A09 Room temperature sensor (external or internal) defective or absent.

A10 Temperature sensor at evaporator defective or absent.

CA11 All compressors have been deactivated. Re-activate with the code menu

EA11 Compressor stopped by de-icing control. Automatic re-start. This error is

only visible in the evaporator temperature read-out E10.0.

Warranty claims

Failure to follow the installation manual and the information, recommendations and descriptions

therein will void all warranties. The same applies if repairs are carried out incorrectly, with the use

of non-genuine parts or by unauthorized personnel. Warranty claims are only valid if the claimant

can verify that he has complied with the maintenance and safety instructions.

Maintenance

Check monthly •Air filter in the return air grilles (where applicable) and clean if necessary.

•Sea water circuit for leaks in the whole system from the sea-cock to the

sea water exit.

•Condensation drain for free flow and leaks.

•Air-ducting for damage, interruption and free flow.

•Function of the system by having it run for at least 10 minutes.

Winter storage At frost temperatures the whole sea water circuit must be emptied and the

sea water valve closed.

Autres manuels Webasto Climatiseur

Webasto

Webasto Cool Top Trail 36V Manuel utilisateur

Webasto

Webasto BlueCool S Series Manuel utilisateur

Webasto

Webasto BlueCool Premium Manuel utilisateur

Webasto

Webasto Cool Top Vario 10 E Manuel utilisateur

Webasto

Webasto BlueCool Classic Instructions d'utilisation

Webasto

Webasto FCF 16,000 Manuel utilisateur

Webasto

Webasto Platinum FCF 24,000 BTU Manuel utilisateur

Webasto

Webasto BlueCool V-PRO Series Manuel utilisateur

Webasto

Webasto Cool Top RTE 10 Manuel utilisateur

Webasto

Webasto Diavia Santana L Manuel utilisateur

Webasto

Webasto Compact Cooler 4E Manuel utilisateur

Webasto

Webasto BlueCool V-Series Manuel utilisateur

Webasto

Webasto Cool Top RTE 16 Manuel utilisateur

Webasto

Webasto Cool Top Vario 10 E Manuel utilisateur

Webasto

Webasto Frigo Top 25 DS Manuel utilisateur

Webasto

Webasto BlueCool C-Series Manuel utilisateur

Webasto

Webasto FCF 10,000 BTU Manuel utilisateur

Webasto

Webasto Cool Top RTE 16 Manuel utilisateur

Webasto

Webasto WBCC Series Fiche technique

Webasto

Webasto Cool Top 110 RT-C Manuel utilisateur

Webasto

Webasto FCF 5,000 Manuel utilisateur

Webasto

Webasto Cool Top 140 Manuel utilisateur

Webasto

Webasto FCF Series Manuel utilisateur

Webasto

Webasto Cool Top Trail 34 Manuel utilisateur

Manuels Climatiseur populaires d'autres marques

Spheros

Spheros CC 355 Manuel utilisateur

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manuel utilisateur

Panasonic

Panasonic CS-E12HKEW Manuel utilisateur

nedis

nedis ACMB1WT7 Manuel utilisateur

Samsung

Samsung AR KV Series Mode d’emploi

Daikin

Daikin FCFV50A Manuel utilisateur

Fujitsu

Fujitsu Inverter ASBA30JFC Manuel utilisateur

Toshiba

Toshiba RAS-M10SMUV-E Manuel utilisateur

Daikin

Daikin FXLQ20MAVE Manuel utilisateur

Hitachi

Hitachi RAS-E24CAK Manuel utilisateur

CIAT

CIAT Magister 2 Series Mode d’emploi

Bestron

Bestron AAC6000 Manuel utilisateur

Hisense

Hisense 7K Manuel technique

Frigidaire

Frigidaire FFRE0533S1E0 Manuel utilisateur

Samsung

Samsung AS09HM3N Manuel utilisateur

Frigidaire

Frigidaire CRA073PU11 Manuel du propriétaire

Soleus Air

Soleus Air GB-PAC-08E4 Manuel utilisateur

McQuay

McQuay MCK020A Manuel utilisateur