Weaver W10-HD Manuel utilisateur
W10-HD Installation & Operation Manual
10,000 lb. Capacity Overhead
Asymmetric Two Post Lift
Derek Weaver Company, Inc.
2950 SE Loop 820
Fort Worth, TX 76140
817-560-9510
www.derekweaver.com
CONTENTS
Product Features and Specifications ..............................................1
Installation Requirement .............................................................4
Steps of Installation ……………………………………………………………………………….6
Exploded View ...........................................................................25
Test Run ...................................................................................33
Operation Instruction .................................................................35
Maintenance .............................................................................35
Trouble Shooting .......................................................................36
Lift disposal ......................................................................................37
1
I. PRODUCT FEATURES AND SPECIFICATIONS
CLEAR-FLOOR DIRECT-DRIVED MODEL FEATURES
Model W10-HD (See Fig. 1)
·Direct-drived design, minimize the lift spare parts and breakdown ratio
·Dual hydraulic cylinders, designed and made as ANSI standards, utilizing imported oil
seal in cylinder
·Self- lubricating UHMW Polyethylene sliders and bronze bush
·Single-point safety release, and dual safety design
. Clear-floor design, provide unobstructed floor use
. Overhead safety shut-off device prevents vehicle damage
·Super-asymmetric arms design can fit extremely wide vehicles, stackable rubber pads
. Standard adjustable heights accommodate varying ceiling heights
W10-HD SPECIFICATIONS
Model
Style
Lifting
Capacity
Lifting
Time
Lifting Height
Overall Height
Overall
Width
Width
Between
Columns
Minimum
Pad Height
Motor
W10-HD
Clear-floor
Direct-drived
10,000 lbs
56S
71 1/2’’-84 1/2’’
142-1/2”/150-1/2”
135”
112 1/4”
3 1/2’’-12 1/2’’
2.0 HP
Fig. 1
Please read carefully
before operation!
2
Arm Swings View
Attention! Please make sure to place the arms in correct
position before car drive in!
Car in
Fig 3
Fig 2
3
II. INSTALLATION REQUIREMENT
A. TOOLS REQUIRED
Rotary Hammer Drill (Φ19)
Hammer
Level Bar
English Spanner (12")
Ratchet Spanner with Socket (28#)
Wrench set
(8#, 10#, 13#, 14#, 17#, 19#, 24#)
Carpenter’s Chalk
Screw Sets
Tape Measure (7.5m)
Pliers
Socket Head Wrench (3#, 5#, 8#)
Lock Wrench
Fig.4
4
B. Equipment storage and installation requirements.
The equipment should be stored or installed in a shady, normal temperature,
ventilated and dry place.
C. The equipment should be unload and transfer by forklift.
D. SPECIFICATIONS OF CONCRETE (See Fig. 6)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 6” minimum and without reinforcing steel bars, and
must be dried completely before the installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
minimum.
3. Floors must be level and no cracks.
E. POWER SUPPLY
The electrical source must be 2.0HP minimum. The source cable size must be 2.5mm²
and in good condition of contacting with floor.
Fig. 6
Concrete must be 3,000psi
minimum
49
Fig.5
6’’
5
III.STEPS OF INSTALLATION
A. Location of Installation
Check and insure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
B. Use a carpenter’s chalk line to establish installation layout of base-plate (See Fig.7).
C. Check the parts before assembly.
1. Packaged lift and power unit (See Fig. 8).
2. Move aside the lift with fork lift or hoist, and open the extension packing carefully, take
off the lifting arms and parts box from upper and inside the column, then move them
to location nearby installation site, check the parts according to the shipment parts
list (See Fig.9).
Shipment Parts list
Top Connecting
Assy.
Parts box
Aluminum
Name plate
Extension Column
（Outer Column）
Lifting Arm
Fig. 7
Fig. 8
Fig. 9
Click a line
135”
6
3. Loose the screws of the upper package stand, take off the upper extension columns,
take out the parts in the inner column and remove the package stand.
4. Move aside the parts and check the parts according to the shipment parts list.
(See Fig.10, 11).
5. Open the bag 1 of parts and check the parts according to parts box list (See Fig. 12).
6. Open the bag 2 of parts and check the parts according to parts bag list (See Fig. 13).
Fig. 10
Parts in the shipment parts list
Fig. 12
50
Fig. 11
Parts in the parts box (50)
Fig. 13
7
D. Install parts of extension columns (See Fig. 14).
E. Position powerside column
Lay down two columns on the installation site paralleled, position the power-side
column according to the actual installation site. Usually, it is suggested to install
power-side column on the front-right side from which vehicles are driven to the lift.
This lift is designed with 2-Section columns. Adjustable height according to the ceiling
height and connecting the inner and extension columns.
W10-HD: Not suitable for installation when the height of the workshop is less than
143-4 / 4 "; only low setting installation for height between 143-5 / 4" -151-5 / 8 ";
the height of the workshop is greater than 151 -5/8 ", installation can be in both high
and low setting;
Fig. 14
26
37
25
24
23
41
42
Table des matières
Autres manuels Weaver Système de levage
Manuels Système de levage populaires d'autres marques
morse
morse 82H-124 Manuel utilisateur
Braun
Braun NL955 Series Manuel utilisateur
haacon
haacon 1889.10 Manuel utilisateur
Protekt
Protekt AT 252 Manuel utilisateur
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manuel utilisateur
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manuel utilisateur
Genie
Genie Z-60/34 Manuel utilisateur
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuel utilisateur
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuel de programmation
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuel de programmation
